Garden Oasis RETRO STEEL CLAM GLIDER RED User manual

See our extensive assortment of outdoor living products
on-line at www.sears.com and www.kmart.com
OWNER’S
MANUAL
RETRO STEEL CLAM
GLIDER - RED Date of purchase: _____/ _____/ _____
Product code: D71 M80154
KSN: 02619890-3
UPC code: 045774 873160
Made in / Hech en CHINA
Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179
sears.com
Please refer to part numbers when reordering
For questions or comments about product:
Email: [email protected] or Call toll-free: 1-877-998-1697

COMPLETED
2pcs
2pcs
2pcs
2pcs
1pc
1pc
4pcs
8pcs
14pcs
6pcs
58pcs
8pcs
22pcs
27pcs
Backrest
Seat plate
Armrest
Crossbar with bracket
Crossbar
Support base
Connect
M6x15 bolt
M6x50 bolt
M6x45 bolt
6 metal washer
M6 nut
M6 bolt cap
φ
φ6 plastic washer
A
B
C
D
E
F
G
H
I
J
K
L
M
N
PARTS LIST
ASSEMBLY
If you any questions regarding assembly of this product,or need additional parts,pleasecontact NSI at
1-877-998-1697from 9:00AM to 5:00 PM EST Monday to Friday or email
for assistance
[email protected]
.
Page1
View the expanded assortment of outdoor living product on-line at
WWW.kmart.com and WWW.sears.com
Note: Leave nuts half-tightened and do not cover the bolt cap during assembly until unit is completely assembled, then
finish tightening nuts and cover the bolt cap accordingly.
Step 1: Attach one of Backrest (A) to a Seat plate (B) with 4 M6 x 15 bolts (H), 8 6 metal washers (K) and 4 M6 nuts (M).
Repeat the same procedure for the other Backrest (A) and Seat plate (B).
Step 2: Attach one of Crossbar with bracket (D) to the bottom hole on the front side of armrest (C) with 1 M6 x 50 bolt (I),
1 6 metal washer (K). Repeat the same procedure for the other side.
Step 3: Attach one of Crossbars (E) to the bottom hole on the rear side of armrest (C) with 1 M6 x 50 bolt (I), 1 6 metal
washer (K). Repeat the same procedure for the other side. Do the same procedure for the Crossbar with bracket (D) as
Crossbar (E) to the middle hole on the rear side of Armrest (C).
Step 4: Place the 2 assembled Backrest and Seat plate onto the assembled armrest. Half-tighten the armrest with bracket
with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 1 6 plastic washer (L), and 1 M6 nut (M). Repeat the same procedure
for the other side.
Step 5: Half-tighten 2 backrests and the bracket on Crossbar (D) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 2 6
plastic washer (L), and 1 M6 nut (M)
Step 6: Half-tighten the armrest (C) and Seat plate (B) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 1 6 plastic
washer (L), and 1 M6 nut (M). Repeat the same procedure for the other side.
Step 7: Half-tighten the 2 Seat plates and the bracket of Crossbar (D) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 2 6
plastic washers (L), 1 M6 nut (M)
Step 8: Attach the one of Connect (G) to Support base (F) with 1 M6 x 50 bolt (I), 2 6 metal washers (K), and 1 M6 nut (M).
Repeat the same procedure for the rest of connects (G).
Step 9: Place chair assembly on the support base (F), screwing the connect (G) to the Armrest (C) with 1 M6 x 50 bolt (I), 2
6 metal washers (K), 1 M6 nut (M). Repeat the same procedure for the rest of connects (G).
Tighten all nuts and cover the bolts with M6 bolt cap (N) accordingly
φ
φ
φ
φφ
φφ
φφ
φφ
φ
φ
Tools Required: Open end wrench provided()
STEP1
STEP2
STEP3
STEP4
STEP5
STEP6 STEP7
STEP8
STEP9
FRONT
REAR
A
B
C
IN
IN
J
N
J
N
J
N
J
I
I
N
C
D
H
K
K
K
MK
N
KK
K
L
K
KK
K
LK
K
LL
LL
KM
M
M
N
M
K
KN
M
D
F
G
G
D
E
Page2
Printed in China