Gardner Denver ELECTRA-SAVER Service manual

13-21-608
Version: 00
September 7, 2018
ELECTRA-SAVER
ELECTRA-SAVER II
STATIONARY BASE-MOUNTED
COMPRESSOR
AirSmart™CONTROLLER
DOMESTIC and INTERNATIONAL MODELS
EAQ99W –125, 150, and 200 HP, 60 HZ
EBQ99R –125, 150, and 200 HP, 60 HZ
EAU99AB –200 HP, 60 HZ
EBU99H –200 HP, 60 HZ
EAQ99W –100, 125, and 150 HP, 50 HZ
(75, 93, 112 KW)
EBQ99R –125 and 150 HP, (93, 112 KW) 50 HZ
EAU99AB –200 HP, (150 KW) 50 HZ
EBU99H –200 HP, (150 KW) 50 HZ
OPERATING AND
SERVICE MANUAL

13-21-608 Page 1
MAINTAIN COMPRESSOR RELIABILITY AND PERFORMANCE WITH
GENUINE GARDNER DENVER® COMPRESSOR PARTS AND SUPPORT SERVICES
Gardner Denver® Compressor genuine parts, manufactured to design tolerances, are developed for optimum
dependability –specifically for Gardner Denver compressor systems. Design and material innovations are the result
of years of experience with hundreds of different compressor applications. Reliability in materials and quality
assurance is incorporated in our genuine replacement parts.
Your authorized Gardner Denver Compressor distributor offers all the backup you’ll need. An AirSmartänetwork of
authorized distributors provides the finest product support in the air compressor industry.
Your authorized distributor can support your Gardner Denver air compressor with these services:
1. Trained parts specialists to assist you in selecting the correct replacement parts.
2. Factory warranted new and remanufactured rotary screw airends. Most popular model remanufactured
airends are maintained in stock at the factory, for purchase on an exchange basis with liberal core credit
available for the replacement unit.
3. A full line of factory tested AEON™compressor lubricants specifically formulated for use in Gardner Denver
compressors.
4. Repair and maintenance kits designed with the necessary parts to simplify servicing your compressor.
Authorized distributor service technicians are factory trained and skilled in compressor maintenance and repair. They
are ready to respond and assist you by providing fast, expert maintenance and repair services.
To Contact Gardner Denver or locate your local distributor:
visit: www.contactgd.com/compressors
or
call: [phone]
INSTRUCTIONS FOR ORDERING REPAIR PARTS/REMANUFACTURED AIRENDS
Whenever an airend requires replacement or repair, Gardner Denver offers an industry unique, factory
remanufactured airend exchange program. From its modern Remanufacturing center in Indianapolis, IN., Gardner
Denver is committed to supplying you with the highest quality, factory remanufactured airends that are guaranteed to
save you time, aggravation and money
When ordering parts, specify Compressor MODEL, Method of Cooling, POWER and SERIAL NUMBER (see
nameplate on unit). The Airend Serial Numbers are also stamped on top of the discharge bearing carrier castings.
All orders for Parts should be placed with the nearest authorized distributor.
Where NOT specified, quantity of parts required per compressor or unit is one (1); where more than one is required
per unit, quantity is indicated in parenthesis. SPECIFY EXACTLY THE NUMBER OF PARTS REQUIRED.
DO NOT ORDER BY SETS OR GROUPS.
To determine the Right-Hand and Left-Hand side of a compressor, stand at the motor end and look toward the
compressor. Right-Hand and Left- Hand are indicated in parenthesis following the part name, i.e. (RH) and (LH),
when appropriate.

13-21-608 Page 2
WARNING –PROHIBITION –MANDATORY LABEL INFORMATION
Gardner Denver Rotary Screw compressors are the result of advanced engineering and skilled
manufacturing. To be assured of receiving maximum service from this machine, the owner must exercise
care in its operation and maintenance. This book is written to give the operator and maintenance
department essential information for day-to-day operation, maintenance and adjustment. Careful
adherence to these instructions will result in economical operation and minimum downtime.
Boxed text formats are used, within this manual, to alert users of the following
conditions:
Safety Labels are used, within this manual and affixed to the appropriate areas of
the compressor package, to alert users of the following conditions:
Indicates a hazard with a high level of risk, which if not avoided,
WILL
result in death or serious
injury.
Equipment starts automatically
Cutting of Finger or Hand Hazard –Rotating
impeller blade
Cutting of Finger or Hand Hazard –Rotating fan
blade
Health Hazard –Explosive Release of Pressure
High Voltage –Hazard of Shock, Burn, or Death
Present until Electrical Power is Removed
Entanglement of Fingers or Hand/Rotating Shaft

13-21-608 Page 3
Indicates a hazard with a medium level of risk which, if not avoided,
COULD
result in death or
serious injury.
Asphyxiation Hazard –Poisonous Fumes or Toxic Gases in Compressed Air
Indicates a hazard with a low level of risk which, if not avoided,
MAY
result in a minor or
moderate injury.
Burn Hazard –Hot surface
PROHIBITION/MANDATORY ACTION REQUIREMENTS
Do not Operate Compressor with Guard Removed
Do Not Lift Equipment with Hook –No Lift Point
Handle Package at Forklift Points Only
Lockout Electrical Equipment in De-Energized
State
Loud Noise Hazard –Wear Ear Protection
Read the Operator’s Manual Before Proceeding
with Task

13-21-608 Page 4
SAFETY PRECAUTIONS
Safety is everybody’s business and is based on your use of good common sense. All situations or
circumstances cannot always be predicted and covered by established rules. Therefore, use your past
experience, watch out for safety hazards and be cautious. Some general safety precautions are given
below:
Failure to observe these notices could result in injury to or death of personnel.
·Keep fingers and clothing away from rotating fan, drive coupling, etc.
·Disconnect the compressor unit from its power source, lockout and tagout before working on the
unit –this machine is automatically controlled and may start at any time.
·Do not loosen or remove the oil filler plug, drain plugs, covers, the thermostatic mixing valve or
break any connections, etc., in the compressor air or oil system until the unit is shut down and
the air pressure has been relieved.
·Electrical shock can and may be fatal.
·Perform all wiring in accordance with the National Electrical Code (NFPA-70) and any applicable
local electrical codes. Wiring and electrical service must be performed only by qualified
electricians.
·Open main disconnect switch, lockout and tagout before working on the control, wait 10 minutes
and check for voltage.
Failure to observe these notices could result in damage to equipment.
·Stop the unit if any repairs or adjustments on or around the compressor are required.
·Do not use the air discharge from this unit for breathing –not suitable for human consumption.
·An Excess Flow Valve should be on all compressed air supply hoses exceeding 1/2 inch
inside diameter (OSHA Regulation, Section 1926.302).
·Do not exceed the rated maximum pressure values shown on the nameplate.
·Do not operate unit if safety devices are not operating properly. Check periodically. Never
bypass safety devices.

13-21-608 Page 5
TABLE OF CONTENTS
Maintain Compressor Reliability And Performance With
Genuine Gardner Denver Compressor Parts And Support Services.........................................................1
Instructions For Ordering Repair Parts/Remanufactured Airends..............................................................1
Warning –Prohibition –Mandatory Label Information..............................................................................2
Safety Precautions..................................................................................................................................4
Index.......................................................................................................................................................6
List Of Illustrations...................................................................................................................................8
Section 1, General Information ................................................................................................................9
Section 2, Installation.............................................................................................................................13
Section 3, Starting & Operating Procedures...........................................................................................24
Section 4, Controls & Instrumentation....................................................................................................29
Section 5, Lubrication, Oil Cooler, Oil Filter & Separator ........................................................................49
Section 6, Air Filter................................................................................................................................67
Section 7, Coupling ...............................................................................................................................69
Section 8, Maintenance Schedule..........................................................................................................72
Section 9, Troubleshooting....................................................................................................................74
This book covers the following models:
HP (KW) PSIG Model Parts List Controller
Manual
Comm
Module
Manual
125, 150, 200 HP, 60 HZ
100, 125, 150 HP, 50 HZ
(75, 93, 112 kW)
100, 125 & 150
100, 125 & 150
EAQ99W
EAQ99W
13-10-523
13-10-523
13-17-600
13-17-600
13-17-604
13-17-604
125, 150, 200 HP, 60 HZ
125,and 150 HP, 50 HZ
(93, 112 kW)
100, 125, 150, 175 & 200
EBQ99R 213-9-507 13-17-600 13-17-604
100, 125, & 150 EBQ99R 213-9-507 13-17-600 13-17-604
200 HP, 60 HZ 100 & 125
EAU99AB 213-9-509 13-17-600 13-17-604
200 HP, 50 HZ (150 kW) 100 & 125
EAU99AB 213-9-509 13-17-600 13-17-604
200 HP, 60 HZ
200 HP, 50 HZ (150 kW)
100 & 125
EBU99H 213-9-509 13-17-600 13-17-604
100 & 125
EBU99H 213-9-509 13-17-600 13-17-604

13-21-608 Page 6
Index
Addition Of Oil Between Changes...................55
Aftercooler Piping...........................................53
Air Filter Element Life .....................................67
Air Filter Vacuum Switch.................................35
Air Filter, Heavy Duty (Standard) ....................66
Air Filter, Section 6.........................................66
Air Flow In The Compressor System................ 9
Air-Cooled Units, Location..............................14
Airsmart™Operation......................................29
Auxiliary Air Receiver......................................17
Blowdown Valve.............................................32
Blowdown Valve Piping ..................................18
Check
Daily...........................................................26
Cold Ambient Operation .................................55
Cold Weather Operation.................................16
Cold Weather Operation, Installation For ........16
Compression Principle..................................... 9
Compressor..................................................... 9
Compressor Capacity Control - Turn Valve Units
Only............................................................37
Compressor Oil Cooler - Water-Cooled Heat
Exchanger ..................................................60
Control Devices..............................................29
Control Piping.................................................17
Control Transformer .......................................36
Controller .......................................................29
Controls & Instrumentation, Section 4.............29
Cooling, Sealing And Lubrication....................10
Coupling.........................................................68
Coupling, Section 7 ........................................68
Daily Check....................................................26
Discharge Service Line...................................18
Discharge Thermistor.....................................36
Drain
Oil Reservoir...............................................15
Draining And Cleaning Oil System..................57
Electrical Wiring..............................................22
Emergency Stop Push-Button.........................36
Enclosure.......................................................15
Fan Starter.....................................................36
Filling Oil Reservoir ........................................58
Filter Element.................................................66
Foundation.....................................................15
Fuse Blocks....................................................36
General Information, Section 1 ........................ 9
Grounding......................................................22
Heat Exchanger (Oil) Piping............................54
High Temperature Operation ..........................49
Inlet Line ........................................................17
Inlet Screen And Tube ...................................67
Inlet Valve......................................................33
Installation For Cold Weather Operation.........16
Installation, Section 2.....................................13
Lifting Unit......................................................13
Location.........................................................14
Air-Cooled Units.........................................14
Water-Cooled Units....................................15
Lubricant
Recommended...........................................48
Lubricant Change Procedure..........................55
Lubrication
Motor..........................................................22
Lubrication, Cooling And Sealing....................10
Lubrication, Oil Cooler, Oil Filter & Separator .48
Main Starter...................................................36
Maintenance Schedule, Section 8..................71
Minimum Discharge Pressure Valve...............32
Moisture Separator/Trap ................................17
Motor Lubrication...........................................22
Oil Change Interval........................................56
Oil Cooler - Radiator Type..............................60
Oil Filter.........................................................59
Oil Level Gauge.......................................32, 56
Oil Reservoir..................................................62
Oil Reservoir Drain.........................................15
Oil Separator
Compressor (Gd Eliminatorä).....................63
Inspection...................................................64
Oil Carryover..............................................63
Pressure Differential Gauging.....................63
Removal For Inspection Or Replacement....64
Oil Specifications ...........................................48
Oil System
Compressor................................................48
Draining And Cleaning................................57
Oil System Check ..........................................65
Air And Oil Discharge Temperature.............65
Oil Cooler Oil Pressure Differential (Air-
Cooled Radiator).....................................65
Oil Cooler Oil Pressure Differential (Water-
Cooled Heat Exchanger).........................65
Oil Cooler Temperature Differential (Air-
Cooled Radiator).....................................65
Oil Cooler Temperature Differential (Water-
Cooled Heat Exchanger).........................65
Oil Cooler Water Pressure Differential (Water-
Cooled Heat Exchanger).........................65
Oil Inlet Pressure........................................65
Oil Inlet Temperature..................................65
Operation
High Temperature.......................................49

13-21-608 Page 7
Parallel Piping................................................22
Piping
Series.........................................................21
Power Supply.................................................36
Pressure Differential Gauging.........................63
Pressure Regulator.........................................34
Prestart-Up Instructions..................................24
Purge Valve....................................................34
Quick Start Guide...........................................27
Relief Valve....................................................30
Remote Mounted Elevated Cooler Assembly..53
Reservoir Pressure Transducer ......................35
Reservoir Thermistor......................................36
Safety Precautions.......................................... 4
Sealing, Lubrication And Cleaning..................10
Section 1, General Information ........................ 9
Section 3, Starting & Operating Procedures....24
Section 4, Controls & Instrumentation.............29
Section 5, Lubrication, Oil Cooler, Oil Filter &
Separator....................................................48
Section 6, Air Filter.........................................66
Section 7, Coupling ........................................68
Section 8, Maintenance Schedule...................71
Section 9, Troubleshooting.............................73
Series Piping..................................................21
Service Check List..........................................71
Every 125 Hours Operation.........................71
Every Year.................................................71
Motor Lubrication........................................71
Oil Separator..............................................71
Service Check List
Air Filter......................................................71
Shuttle Valve..................................................34
Solenoid Valves Ivc And Ivo...........................34
Solenoid Valves Tvc And Tvo.........................35
Starting & Operating Procedures, Section 3 ...24
Starting The Unit............................................26
Unit Cold....................................................26
Unit Hot......................................................26
Stopping The Unit..........................................26
System Pressure Transducer.........................35
Terminal Strip ................................................36
Thermal Control (Thermostatic Mixing) Valve.60
Troubleshooting, Section 9.............................73
Turn Valve...............................................10, 35
Turn Valve Actuator .......................................35
Warning –Prohibition –Mandatory Label
Information...................................................2
Water Flow Control Valve For Heat Exchanger
...................................................................62
Water Piping..................................................20
Water Shutoff Valve - Water-Cooled Heat
Exchanger..................................................62
Water-Cooled Units, Location.........................15
Every 1000 Hours Operation.......................71
Every 8 Hours Operation.............................71
Every 8000 Hours Operation.......................71

13-21-608 Page 8
LIST OF ILLUSTRATIONS
Figure 1-1 –Compression Cycle..............................................................................................................9
Figure 1-2 –Starter Box ........................................................................................................................10
Figure 1-3 –Control Box........................................................................................................................10
Figure 1-4 –Compressor / Motor Side...................................................................................................11
Figure 1-5 –Cooler / Reservoir Side......................................................................................................11
Figure 1-6 –Air/Oil Flow Diagram..........................................................................................................12
Figure 2-1 –Typical Compressor Room.................................................................................................14
Figure 2-2 –Air Flow Chart....................................................................................................................14
Figure 2-3 –Cold Weather Installation...................................................................................................16
Figure 2-4 –Inlet Line Lengths ..............................................................................................................17
Figure 2-5 –Heat Exchanger (Oil Cooler) Approximate Water Flow.......................................................19
Figure 2-6 –Aftercooler Approximate Water Flow.................................................................................19
Figure 2-7 –Series Piping .....................................................................................................................21
Figure 2-8 –Parallel Piping....................................................................................................................21
Figure 4-1 –Key Pad.............................................................................................................................30
Figure 4-2 –Schematic Tubing Diagram................................................................................................31
Figure 4-3 –Blowdown Valve ................................................................................................................32
Figure 4-4 –Minmum Discharge Pressure/Check Valve.........................................................................32
Figure 4-5 –Inlet Valve..........................................................................................................................33
Figure 4-6 –Shuttle Valve .....................................................................................................................34
Figure 4-7 –Turn Valve –Electra-Saver Only........................................................................................35
Figure 4-8 –Control Schematic –Compressor Unloaded –Constant Speed Mode ................................38
Figure 4-9 –Control Schematic –Compressor At Full Load –Constant Speed Mode.............................39
Figure 4-10 –Control Schematic –Compressor Unloaded –Low Demand Mode Or Auto Mode ............40
Figure 4-11 –Control Schematic –Compressor At Full Load .................................................................41
Figure 4-12 –Control Schematic –Compressor Fully Unloaded –Low Demand Mode Switch Off..........42
Figure 4-13–Control Schematic –Compressor Fully Loaded –Low Demand Mode Switch On..............43
Figure 4-14 –Wiring Diagram –Wye Delta............................................................................................44
Figure 4-15 –Wiring Diagram –Less Starter .........................................................................................46
Figure 5-1 –Dew Point Chart °F............................................................................................................51
Figure 5-2 –Dew Point Chart °C............................................................................................................51
Figure 5-3 –Flow Diagram –Air/Oil System...........................................................................................52
Figure 5-4 –Oil Flow Diagram –Remote Overhead Mounted Cooler.....................................................53
Figure 5-5 –Cooler Drain Detail.............................................................................................................54
Figure 5-6 –Oil Level Gauge.................................................................................................................57
Figure 5-7 –Oil Change Interval............................................................................................................58
Figure 5-8 –Approximate Oil System Capacities ...................................................................................59
Figure 5-9 –Thermostatic Mixing Valve Element ...................................................................................61
Figure 5-10 –Water Control Valve.........................................................................................................62
Figure 5-11 –Oil Separator ...................................................................................................................64
Figure 6-1 –Heavy Duty Air Filter..........................................................................................................67
Figure 7-1 –Installation Of Coupling Cushions.......................................................................................69

13-21-608 Page 9
SECTION 1
GENERAL INFORMATION
Figure 1-1 –COMPRESSION CYCLE
COMPRESSOR - The Gardner Denver Rotary Screw compressor is a single stage, positive displacement
rotary machine using meshing helical rotors to effect compression. Both rotors are supported between
high capacity roller bearings located outside the compression chamber. Single width cylindrical roller
bearings are used at the inlet end of the rotors to carry part of the radial loads. Tapered roller bearings at
the discharge end locate each rotor axially and carry all thrust loads and the remainder of the radial loads.
COMPRESSION PRINCIPLE (Figure 1-1) - Compression is accomplished by the main and secondary
rotors synchronously meshing in a one-piece cylinder. The main rotor has four (4) helical lobes 90°apart.
The secondary rotor has six (6) matching helical grooves 60°apart to allow meshing with main rotor
lobes.
The air inlet port is located on top of the compressor cylinder near the drive shaft end. The discharge port
is near the bottom at the opposite end of the compressor cylinder. Figure 1-1 is an inverted view to show
inlet and discharge ports. The compression cycle begins as rotors unmesh at the inlet port and air is
drawn into the cavity between the main rotor lobes and secondary rotor grooves (A). When the rotors
pass the inlet port cutoff, air is trapped in the interlobe cavity and flows axially with the meshing rotors (B).
As meshing continues, more of the main rotor lobe enters the secondary rotor groove, normal volume is
reduced and pressure increases.
Oil is injected into the cylinder to remove the heat of compression and seal internal clearances. Volume
reduction and pressure increase continues until the air/oil mixture trapped in the interlobe cavity by the
rotors passes the discharge port and is released to the oil reservoir (C). Each rotor cavity follows the
same “fill-compress-discharge”cycle in rapid succession to produce a discharge air flow that is
continuous, smooth and shock free.
AIR FLOW IN THE COMPRESSOR SYSTEM (Figure 5-3, page 52) - Air enters the air filter and passes
through the inlet unloader valve to the compressor. After compression, the air/oil mixture passes into the
oil reservoir where most of the entrained oil is removed by velocity change and impingement and drops
back into the reservoir. The air and remaining oil passes into the separator and separator housing where
the oil is separated and passes through tubing connecting the separator housing and compressor. The
air passes through the minimum pressure valve, discharge check valve and cooler, then to the plant air
lines.

13-21-608 Page 10
LUBRICATION, COOLING AND SEALING - Oil is forced by air pressure from the oil reservoir through
the oil cooler, thermostatic mixing valve, and oil filter and discharges into the compressor main oil gallery.
A portion of the oil is directed through internal passages to the bearings, gears and shaft oil seal. The
balance of the oil is injected directly into the compression chamber to remove heat of compression, seal
internal clearances and lubricate the rotors.
TURN VALVE (ELECTRA-SAVER ONLY) - The turn valve is a rotary helical valve located on the
discharge side of the cylinder toward the inlet end. The valve opens and closes ports in the cylinder
which communicates with the inlet passage. This varies the compressor rotor volume to match the
demand for air, thus reducing the part-load power requirement.
Figure 1-2 –STARTER BOX
Figure 1-3 –CONTROL BOX
200EDM797
-
A
(Ref. Drawing)

13-21-608 Page 11
Figure 1-4 –COMPRESSOR / MOTOR SIDE
Figure 1-5 –COOLER / RESERVOIR SIDE
200EDM797
-
A
(Ref. Drawing)

13-21-608 Page 12
Figure 1-6 –AIR/OIL FLOW DIAGRAM
202EDM797
(Ref. Drawing)

13-21-608 Page 13
SECTION 2
INSTALLATION
GENERAL - On receipt of the unit, check for any damage that may have been incurred during transit. Report
any damage or missing parts as soon as possible.
Do not electric weld on the compressor or base; bearings can be damaged by
passage of current.
LIFTING UNIT - Proper lifting and/or transporting methods must be used to prevent damage. Lifting slots are
provided in the base for tow motor use. The unit may also be moved into location by rolling on bars.
Lift compressor package by base only. Do not use other places such as
motors, compressors or discharge manifold piping as lifting points.
The eyebolts or lugs provided on the motors are for lifting the motors only and
should not be used to lift any additional weight. All eyebolts must be securely
tightened. When lifting the motors, the lifting angle must not exceed 15
degrees. Failure to observe this warning may result in damage to equipment or
personal injury.
Compressor, air/oil reservoir, separator chamber and all piping and tubing may
be at high temperature during and after operation.

13-21-608 Page 14
LOCATION - The compressor should be installed, whenever possible, in a clean, well-lighted, well-
ventilated area with ample space all around for maintenance. Select a location that provides a cool,
clean, dry source of air. In some cases it may be necessary to install the air filter at some distance from
the compressor to obtain proper air supply.
Both the air-cooled and water-cooled units require cooling air as well as air to the compressor inlet.
Proper ventilation MUST be provided; hot air must be exhausted from the compressor operating area. A
typical inlet-outlet air flow arrangement is shown in Figure 2-1.
Figure 2-1 –TYPICAL COMPRESSOR ROOM
Air-Cooled Units - A combination oil/aftercooler is supplied as standard equipment on all air-cooled
units. The air-cooled unit with the standard enclosure requires sufficient flow, Figure 2-2, for the
compressor oil/aftercooling system and for electric motor cooling. Air is drawn into the unit at the motor
side of the enclosure and is exhausted at the oil cooler side. Do not block the air flow to and from the
unit. Allow three and one-half (3-1/2) feet (1.1 m) to the nearest obstruction on the starter end and control
box end of the unit. Allow three (3) feet (.9 m) to the nearest obstruction above and on other sides of unit.
For continuous efficiency, oil cooler cores must be periodically cleaned with either vacuum or compressed
air. If wet cleaning is required, shield motor and spray on a mild soap solution and flush with clean water.
Minimum Air Flow * For Compression and Cooling
HP (kW) Air Cooled Water Cooled
125, 150, 200
(93, 112, 150) 17,000 cfm 481 m3/min 4,000 cfm 113 m3/min.
* 80
°
F (27
°
C) Inlet Air
Figure 2-2 –AIR FLOW CHART

13-21-608 Page 15
NOTICE
These compressors have aluminum oil coolers; do not use any cleaning
solution that is not compatible with aluminum. Use of improper solution may
result in damage to the cooler.
Water-Cooled Units - The water-cooled unit with the standard enclosure requires sufficient air flow,
Figure 2-2, for electric motor cooling. Air is drawn into the unit at the top of the enclosure and is
exhausted at the motor side. Do not block air flow to and from unit. Allow three and one-half (3-1/2) feet
(1.1 m) to the nearest obstruction on the starter end and control box side of the unit. Allow three (3) feet
(.9 m) to the nearest obstruction above and on other sides of the unit.
FOUNDATION - The Gardner Denver Rotary Screw compressor requires no special foundation, but
should be mounted on a smooth, solid surface. Whenever possible install the unit near level. Temporary
installation may be made at a maximum 10°angle lengthwise or 10°sidewise.
Mounting bolts are not normally required. However, installation conditions such as piping rigidity, angle of
tilt, or danger of shifting from outside vibration or moving vehicles may require the use of mounting bolts
and shims to provide uniform support for the base.
OIL RESERVOIR DRAIN - The oil drain is piped from the bottom of the reservoir to the side of the frame.
This drain is approximately 4.50 inches (115 mm) above the floor level. If this is not sufficient to
conveniently drain the oil some other methods of providing drain are:
1. Elevate the compressor unit on a suitable structure to obtain the desired drain height.
2. Construct an oil sump or trough below the floor level and pump or bail the drained oil.
3. Pump oil from the reservoir filler opening or drain to a container.
If the compressor unit base is raised above floor level, the space between the
floor and the base bottom must be closed with solid material all around to
prevent recirculation of hot air from the oil cooler end and over temperature
operation.
ENCLOSURE - The compressor, electric motor, oil cooler and aftercooler are mounted inside the
enclosure. Service doors are provided for maintenance access. Be sure to allow enough space around
the unit for the doors to open completely. Any of the enclosure doors may be removed by opening the
door and lifting it up slightly to disengage the hinges.
The motor inspection/air filter service panel is held by two latches and lifts away from the enclosure. The
air outlet panel is attached by screws to the enclosure and is not readily removable.

13-21-608 Page 16
Do not operate the compressor with the fan and coupling guard removed.
Exposed fan and couplings may cause injury to personnel.
Figure 2-3 –COLD WEATHER INSTALLATION
INSTALLATION FOR COLD WEATHER OPERATION (Figure 2-3) - It is recommended that the unit be
installed inside a shelter that will be heated to temperatures above freezing (32°F, 0°C). This will
eliminate many of the problems associated with operating units in cold climates where freezing rain,
drifting snow, freezing condensate and bitter cold temperatures are encountered.
Refer to Engineering Data Sheet 13-9-411 for the advantages of using the heat recovered from rotary
compressors. This heat recovery could easily pay for an adequate shelter for the unit.
When an outside installation must be made, the precautions required will depend on the severity of the
environment. The following are general guidelines for outside installations:
Cold Weather (Down To +10°F, -12°C)
1. Be sure all drains, traps, and control lines, including pressure transducer lines are heated to avoid
freezing of condensate. Heat tape with thermostat control is generally satisfactory for this purpose
and can be obtained at various local plumbing or hardware outlets at nominal cost.
2. If an air-cooled aftercooler is to be used, provisions to bypass the aftercooler must be made. Since
cold air contains very little moisture, successful operation can be achieved without the aftercooler.
3. Provide at least some simple shelter such as a plywood windbreak to protect against drifting snow.
4. Use only Gardner Denver AEON 9000 SP lubricant.
5. Monitor the unit carefully during start-up and operation to be sure it is functioning normally.
6. Specify NEMA 4 enclosure for electrical devices

13-21-608 Page 17
Extreme Cold Weather Operation (Down To -10°F, -23°C)
In addition to the above, the following should be provided:
1. It will be necessary to provide shutters or to block off part of the cooler in some manner since the
cooler is greatly oversized for operation in these low temperatures. Since shutters are not provided
as a factory option, blocking off a portion of the cooler with plywood should be satisfactory.
2. Auto operation should not be used in extreme environments.
3. Some means of providing heat during shutdown. Start-up should be provided. There are various
methods to accomplish this, but since openings are not provided for sump heaters, the use of radiant
heaters is recommended. The heaters should be sized to provide at least a +10°F (-12°C)
environment for coolers, motor and sump. Figure 2-3, page 16, shows how these might be located
in a typical installation and sizes required.
Remember unsheltered (outside) installations should be avoided where possible. Installation next to a
heated building where enough heat can be used to keep the compressor room above freezing will save
many complications in the operation and installation of the unit.
Refer to Engineering Data Sheet 13-9-411, available from an authorized Gardner Denver distributor, for
the advantages of using the heat recovered from rotary compressors. This heat recovery could easily
pay for an adequate shelter for the unit.
AUXILIARY AIR RECEIVER - An auxiliary air receiver is not required if the piping system is large and
provides sufficient storage capacity to prevent rapid cycling. When used, an air receiver should be of
adequate size, provided with a relief valve of proper setting, a pressure gauge and a means of draining
condensate.
MOISTURE SEPARATOR/TRAP - Since the unit is equipped with a built-in aftercooler, a combination
moisture separator and trap is recommended but optional.
CONTROL PIPING - Control piping is not necessary since the Rotary Screw compressor unit is factory
wired and piped for the control system specified.
INLET LINE - Where an inlet line is used between the air filter and the compressor, it must be thoroughly
cleaned on the inside to prevent dirt or scale from entering the compressor. If welded construction is
used, the line must be shot blasted and cleaned to remove welding scale. In either case, the inlet
line must be coated internally by galvanizing or painting with a moisture and oil-proof sealing lacquer. Up
to ten (10) feet (3 meters) in length, the inlet line should be the full size of the inlet opening on the
compressor. If an extra-long line is necessary, the pipe size should be increased according to Inlet Line
Length Chart, Figure 2-4.
Accessibility for inlet air filter servicing must be considered when relocating the filters from the unit to a
remote location.
INLET LINE LENGTHS
Length of Inlet Line Diameter of Pipe Size
0 to 10 Feet (0 to 3 Meters)
................................
Same as Compressor Inlet Opening
10 to 17 Feet (3 to 5 Meters)
................................
One Size Larger Than Inlet Opening
17 to 38 Feet (5 to 11.5 Meters)
................................
Two Sizes Larger Than Inlet Opening
Figure 2-4 –INLET LINE LENGTHS

13-21-608 Page 18
DISCHARGE SERVICE LINE - The discharge service line connection on both water-cooled and air-
cooled units is made at the right hand corner of the unit, viewed from the opposite end from control panel
side. When connecting two or more GD rotary screw units on a common manifold, each unit is isolated
by the check valve in the unit discharge line. If a Gardner Denver rotary screw unit is connected to
another compressor on a common manifold be sure the other compressor has a check valve in the line
between the machine and the manifold. If a rotary screw and a reciprocating compressor are connected
together on a common manifold, an air receiver must be located between the two units.
Discharge air used for breathing will cause severe injury or death.
Consult filtration specialists for additional filtration and treatment equipment to
meet health and safety standards.
BLOWDOWN VALVE PIPING - The blowdown valve is piped back into the airend between the inlet valve
and air filter.
HEAT EXCHANGER
Water Temperature to Heat
Exchanger
(gpm)
Maximum
Water Flow
(gpm) **
Approximate Water
Pressure Drop @ 90°F
Water Temperature
(psi)
HP Model 60
°
F 70
°
F 80
°
F 90
°
F
125 HP EAQ99W 12.1 15.2 20.2 30.3 40.0 4.0
125 HP EBQ99R 11.3 14.1 18.9 28.3 40.0 4.0
150 HP EAQ99W 14.6 18.2 24.3 36.4 40.0 4.0
150 HP EBQ99R 13.1 16.3 21.8 32.7 40.0 4.5
200 HP EAQ99W 18.3 22.8 30.4 45.5 110.0 5.0
200 HP EAU99Y 18.9 23.6 31.5 47.3 110.0 5.0
200 HP EBU99F 18.9 23.6 31.5 47.3 110.0 5.0
200 HP EBQ99R 16.4 20.4 27.3 40.9 110.0 5.0
* 80
°
F Maximum Water Temperature when aftercooler & oil cooler are piped in series (std).
** Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.

13-21-608 Page 19
HEAT EXCHANGER (INTERNATIONAL)
Water Temperature to Heat
Exchanger
(l/s)
Maximum
Water Flow
(l/s) *
Approximate Water
Pressure Drop @ 32°C
Water Temperature
(bar)
KW Model 16°C 21°C 27°C 32°C
75 EAQ99W 0.51 0.64 0.85 1.28 2.52
Less than .15 bar for any
flow rate shown in the table
93 EAQ99W,
EBQ99R 0.68 0.85 1.14 1.70 2.52
112 EAQ99W,
EBQ99R 0.81 1.02 1.35 2.03 2.52
175 EBU99F 1.00 1.26 1.68 2.52 7.0
* Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.
Figure 2-5 –HEAT EXCHANGER (OIL COOLER) APPROXIMATE WATER FLOW
AFTERCOOLER (DOMESTIC)
Water Temperature to Heat
Exchanger
(gpm)
Maximum
Water Flow
(gpm) *
Approximate Water Pressure
Drop @ 90°F Water
Temperature
(psi)
HP Model 60
°
F 70
°
F 80
°
F 90
°
F
125 HP EAQ99W 1.9 2.4 3.2 4.8 55
Less than 1 PSI for any flow
rate shown in the table
125 HP EBQ99R 1.8 2.2 3.0 4.5 55
150 HP EAQ99W 2.3 2.9 3.9 5.8 55
150 HP EBQ99R 2.1 2.6 3.4 5.2 55
200 HP EAQ99W 2.9 3.6 4.9 7.3 110
200 HP EAU99Y 3.0 3.7 5.0 7.5 110
200 HP EBU99F 3.0 3.7 5.0 7.5 110
200 HP EBQ99R 2.6 3.3 4.3 6.5 110
* Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.
AFTERCOOLER (INTERNATIONAL)
Water Temperature to Heat Exchanger
(l/s) Maximum
Water Flow
(l/s) *
Approximate Water Pressure
Drop @ 32°C Water
Temperature
(bar)
kw Model 16°C 21°C 27°C 32°C
75 EAQ99W 0.08 0.10 0.14 0.20 3.47
Less than .1 bar for any flow
rate shown in the table
93 EAQ99W,
EBQ99R 0.11 0.13 0.18 0.27 3.47
112 EAQ99W,
EBQ99R 0.13 0.16 0.21 0.32 3.47
130 EBU99F 0.16 0.20 0.26 0.40 7.0
* Flows exceeding "Maximum Water Flow" will cause severe erosion and will void unit warranty.
Figure 2-6 –AFTERCOOLER APPROXIMATE WATER FLOW