Garmin WORKFORCE 320 Manual

GTX 320
TRANSPONDER
Pilot’s
Guide

Operating The GTX 320
The GTX 320 owner accepts all responsibility for obtaining the proper license before
using the transponder.
The coverage you can expect from the GTX 320 is limited to “line of sight”. Low altitude
or aircraft antenna shielding by the aircraft itself may result in reduced range. Range can
be improved by climbing to a higher altitude. It may be possible to minimize antenna
shielding by locating the antenna where dead spots are only noticed during abnormal
flight attitudes.
Function Selector Switch
The function selector switch is a five position rotary switch. The five positions are:
• OFF—Turns off all power to the GTX 320 (the GTX 320 should be turned off before starting
aircraft engine(s).
• SBY—Turns the transponder on, but when in SBY the GTX 320 will not reply to any interro-
gations from the ground radar system.
• ON—Places the transponder in Mode A, the identification mode. In addition to the aircraft’s
identification code, the GTX 320 will also reply to altitude interrogations (Mode C) with sig-
nals that do not contain altitude information.
• ALT—Activates all of the necessary circuitry (transponder to optional altitude digitizer and
return) to respond to ATC altitude interrogations and aircraft identification interrogations with
standard pressure altitude (29.92 inches Hg). The ALT position may be used in aircraft that
are not equipped with the optional altitude digitizer, however, the only response will be dis-
creet signals that do not contain altitude information.
• TST—Turning the switch to the TST position tests the reply indicator. The TST position is
spring loaded and must be held momentarily. When released, it will automatically return to
the ALT position.
NOTES
IDENT BUTTON
FUNCTION SELECTION KNOB
REPLY LIGHT
CODE SELECTION KNOBS

Any time the function switch is in the ON or ALT position the transponder becomes an active part
of the beacon system. Select ON or ALT as late as practical prior to takeoff and switch to OFF or SBY
as soon as practical after completing landing roll unless the change to SBY has been accomplished
previously at the request of ATC.
Code Selector
The code selector consists of four, eight position switches that provide 4,096 active identification
codes. Attention should be paid to the selected identification code. The selected code should be in
accordance with instructions for IFR flight or rules applicable to transponder utilization for VFR
flight.
When making routine code changes, you should avoid inadvertent selection of codes 7500, 7600,
or 7700 thereby causing momentary false alarms at automated ground facilities. For example when
switching from code 2700 to code 7200, switch first to 2200 then 7200, NOT to 7700 and then
7200.
This procedure applies to nondiscrete code 7500 and all discrete codes in the 7600 and 7700 series
(i.e., 7600-7677, 7700-7777) which trigger special indicators in automated facilities. Only nondis-
crete code 7500 will be decoded as the hijack code. An aircraft’s transponder code (when available)
is utilized to enhance the tracking capabilities of the ATC facility, therefore you should not turn the
GTX 320 to SBY when making routine code changes.
Important Codes
• 1200—The VFR Code for any altitude.
• 7600—Loss of Communications.
• 7500—Hijacking (Never assigned by ATC without prior notification of the pilot that his or
her aircraft is subject to unlawful interference).
• 7700—Emergency (All secondary surveillance radar sites are ready to receive this code at all
times).
See the Airman’s Information Manual (AIM) for a detailed explanation of identification codes.
IDENT Button
On occasion, the controller will request “SQUAWK IDENT”. Respond by momentarily pressing and
releasing the IDENT button. Pressing the IDENT button activates the Special Position Identification
Pulse (SPI) for approximately 20 seconds identifying your transponder return from other aircraft on
the controller’s scope.
Reply Light
The reply light will blink each time the transponder replies to ground interrogation. The reply light
remains lit up during the IDENT time interval.

© 1997 GARMIN CORPORATION
1200 E. 151st Street, Olathe, KS USA 66062-3426
Telephone [phone] or 1-800-800-1020 FAX [phone]
http://www.garmin.com
GARMIN (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ U.K.
Telephone [phone] FAX [phone]
Part Number 190-00133-00 Rev. A
®