Garmin 150MGPSKIT User manual

A
GAR MIN ®
Portable Mount
Installation Instructions ... .... ..................................... ..... ........ ......... ............ 2
Instructions d'installation ....................... .... .... ......................... .. .................. 3
lstruzioni di installazione .... ........................................................................ 5
lnstallationsanweisungen ..................................... . ..................................... 7
lnstrucciones de instalaci6n .... ............... .. .. .... ... ....... ... ................. .. ............ 8
lnstru96es de instala9ao ........................... . .......................... .. .. ................ 10
lnstalleringsinstruksjoner ......................................................................... 12
lnstallationsinstruktioner .... .. .. ..... .... .. ........ . ...... .... ...... . .. . .......... .... ... .... ..... 14
Garmin ' a nd the Garmin l ogo are tr ademarks of Garm in Ltd . or it ss ub s id ia r ies , registered in th eU SA and ot her co un tri es . Th ese tr ademark s may not be u sed w it hout t he express pennis sion of Ga rmin.
El ntlm ero de r eg i st ro COFET EU IFE T EL puede ser r ev i sado en el manual a tr aves de Ia sig ui ente pag i na de intern e t.
CE
November 2015 Pr
inted in Taiwan 190 - 02 0 08 -02_ OA

Portable Mount Installation Instructions
Getting Started
&.WARNING
See the Important Safety and Product Information guide in the product box for
product warnings and other important information.
Assembling the Mount
Before you can assemble the mount, you must have a Phillips screwdriver.
1 Insert the handle CD into the two openings on the portable mount (2~ .
2 Attach the handle to the portable mount using two M4xQ.?x4Q screws @
and M4x? mm nuts @.
3 Install your fishfinder or chartpotter mount on the portable base.
See your fishfinder or chartplotter installation instructions .
Transducer
The transducer can be configured two ways. You can configure the transducer
with the included suction cup mount for use on the side or bottom of your boat.
You can also configure the transducer with the included float for ice-fishing or
dockside use.
Floating the Transducer
1 While holding the transducer arm in one hand, take a length of the
transducer cable and make a loop.
2 Insert the loop into one end of the float until the loop extends out of the
opposite end of the fl oat.
3 Ensure the length of cable between the float and transducer is long enough
so the transducer can be suspended below the water or ice .
4 Thread the transducer through the loop at the end of fl oat and pull tight.
Mounting the Transducer with the Suction Cup
If you purchased the transducer separately from the portable kit , before you
can mount the transducer on the transducer arm, you must find the hardware
that was packaged with the transducer.
1 Attach the suction cup CD to the transducer arm @ using the shorter screw
@.
2
2 Pull the transducer cable back and insert the transducer or transd u cer
mount into the transducer arm .
If possible , insert the transducer cable through the no t ch and open i ng in
the transducer arm.
3 Place the washers ® on the outside of the transducer arm.
4 Insert the l onger screw @ through the washers and transducer or
transducer mount.
5 Fasten the screw with the wing nut @.
6 Attach the suction cup to your boat.
7 Align the transducer parallel with the water l ine .
Connecting and Stowing the Cables
&.CAUTION
Ensure that you connect the correct connector to the correct battery terminal.
Damage to the battery , device , or bodily harm may occur if the device is
improperly connected to the battery.
Connect the positive (red) connector onto the pos i tive ( red) terminal on the
battery.
2 Connect the negative (black) connector onto the negat i ve (b l ack) term i nal
on the battery.
3 Connect the power cable and transducer cable to the fishfinder or
chartplotter .
4 If necessary, wrap the excess power cable around the open section on the
underside of the portable mount.
5 If necessary, wrap the excess transducer cable around the hooks on the
side of the handle on the portable mount.
Placing the Portable Kit in the Bag
After you have assembled the portable kit mount, you can place it in the bag,
wh i ch makes it easier to carry and protects it from the elements. The bag
contains hooks that allow you to tether the bag to a seat on your boat.
1 Place the battery in the open space behind the swivel mount.
2 Slide two of the i ncluded hook and loop straps through the narrow slots
near the battery .
3 Pull the straps under and around the bottom of the portable mount , and
wrap them tightly around the battery.
4 Place the transducer into the open space next to the sw i vel mount.
5 Place the portable kit in the bag .
6 Wrap the flap of nylon found inside the bag around the hand le of the
portable base and secure it to the opening flap .
7 Pull the opening flap over the handle .
8 Zip up the opening flap to close the bag .
Installation Ins tru ctions

Appendix
Battery Information
Battery Warnings
Your GPS device uses a user-replaceable sealed lead acid battery. If these
guidelines are not followed, the battery may experience a shortened life span
or may present a risk of damage to the device, fire, chemical burn, electrolyte
leak, and/or bodily injury.
.&. WARNING
• When storing the battery for an extended time, store within the following
temperature range: from so F to 104°F (from -1So C to 40° C).
• Do not operate the battery outside of the following temperature range: from
so F to 122° F (from -1So C to sao C).
• Do not place the battery near objects that may cause sparks, flames, or
heat.
• Do not incinerate the battery.
• Keep the battery tightly closed.
• Do not use a sharp object to remove the battery.
• Do not disassemble, puncture, or damage the battery.
• Do not swallow, touch, or inhale the contents of an open battery. Avoid
contact with internal acid. Contact with internal acid may cause irritation or
severe burns. Irritation may occur to the eyes, respiratory system, and
skin. Flush with water at once if contact is made with acid.
• Do not submerge the battery and avoid contact with water.
• Do not short the battery terminals.
• Do not drop or throw the battery.
• Keep the battery away from children.
• Only replace the battery with the correct replacement battery. Using
another battery presents a risk of fire or explosion of the device or charger.
• Only charge the battery with the included charger.
• Do not charge the battery in an unventilated area.
• Store in a cool, dry, and well-ventilated area.
• Do not charge the battery in a gas-tight container.
• Do not leave the device exposed to a heat source or in a high-temperature
location, such as in the sun in an unattended vehicle. To prevent damage,
remove the device from the vehicle or store it out of direct sunlight.
• Do not use organic solvents or other cleaners other than recommended
chemical cleaners on the battery.
• Contact your local waste disposal department to dispose of the battery in
accordance with applicable local laws and regulations.
Charging the Battery
.&. CAUTION
Ensure that you connect the correct connector to the correct battery terminal.
Damage to the battery, device, or bodily harm may occur if the device is
improperly connected to the battery.
Before you can charge the battery using the charger, you must disconnect the
device power cable from the positive and negative terminals on the battery.
The battery is rechargeable and can be charged by connecting the battery to a
wall charger.
1 Connect the positive connector on the wall charger onto the positive
terminal on the battery.
2 Slide the negative connector on the wall charger onto the negative terminal
on the battery.
3 Connect the wall charger to the wall outlet.
Battery Tips
• The life expectancy of a sealed lead acid battery can be extended by
recharging often and not completely discharging the battery.
• Sealed lead acid batteries slowly lose their charge while in storage . For
best results, charge the battery prior to use.
Instru c tions d'installation
When used in cold temperatures, sealed lead acid batteries do not hold the
charge as long as in warmer temperatures.
• To avoid spilling the internal acid, keep the battery in the upright position.
• Sealed lead acid batteries are completely recyclable.
Specifications
r
Battery type
Battery shelf life after charging
Battery operating temperature range
I Sealed lead acid
---+--c:-- 1m- onth: 92%
3 months: 90%
6 months: 80%
From 5o F to 122° F (from
-W Cto50o C)
From 5° F to 104° F (fro:J
-15° C to 40° C)
--+=--
From 5° F to 104° F (from
Physical size (assembled kit with device)
1
-15° C to 40° C)
Lx Wx H: 10.629 in. x
10.629 in. x 11.02 in. (270
mm x 270 mm x 280 mm)
______:____j
Weight (unassembled kit with device)
8.498 lb. (3855 g) ___j
Support portable Instructions d'installation
Mise en route
.&. AVERTISSEMENT
Consultez le guide Informations importantes sur /e produit et Ia securite inclus
dans l'emballage du produit pour prendre connaissance des avertissements et
autres informations sur le produit.
Assemblage du support de montage
Pour pouvoir assembler le support de montage, vous devez disposer d'un
tournevis cruciforme.
lnserez Ia poignee <D dans les deux emplacements situes sur le support
portable@.
2 Fixez Ia poignee au support portable a l'aide de deux vis M4xQ,?x40 ® et
de deux ecrous M4x7 mm @.
3 lnstallez le sondeur ou traceur sur le support portable.
Veuillez vous referer aux instructions d'installation de votre sondeur ou
traceur.
Sonde
La sonde peut etre instalh§e de deux fa9ons. Vous pouvez installer Ia sonde a
l'aide du support a ventouse inclus pour Ia fixer sur les cotes ou le dessous de
votre bateau. Vous pouvez egalement utiliser Ia sonde avec le flotteur fourni
pour pecher so us Ia glace ou depuis un ponton.
Installation du f/otteur de sonde
1 Tout en tenant Ia sonde d'une main, prenez une longueur du cable de Ia
sonde et faites une boucle.
2 lnserez Ia boucle dans l'une des extremites du flotteur jusqu'a ce qu'elle
ressorte par l'autre extremite.
3

©
2015
Ga
rmin
Ltd
.
or
itss
ub
s
idi
aries
www
.
garmin
.
co
m/s
u
pport