Garrett Axiom User manual

Quick Start Guide
ASSEMBLY
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Ce produit est conforme aux normes RSS exemptes de
licence d’Industry Canada. Son fonctionnement est soumis
aux deux conditions suivantes: (1) ce dispositif ne peut pas
provoquer d’interférences et (2) ce dispositif doit accepter
toute interférence, y compris celles pouvant entraîner un
dysfonctionnement.
Wireless Transmitter Specications
Audio Delay: 17 milliseconds
Audio Bandwidth: 30-18,000 Hz
Operating Frequency: 2406–2474 MHz
Transmit Power: 8.6 dBm EIRP
Certications: FCC, CE, IC, AS/NZ
Release clamp, extend lower stem. Press the mounting
washers into place.
Insert lower stem into
searchcoil bracket.
Insert bolt, and hand-
tighten wing nut.
Wrap cable around stem, with the rst
turn of cable over the stem. Attach to
back of control box, tighten collar.
REGULATORY INFORMATION / INFORMACIÓN NORMATIVA / INFORMATIONS RÉGLEMENTAIRES
© 2022 Garrett Electronics, Inc. PN 1557400.A.0522
Click to access detailed Axiom guides in other languages.
Cliquez pour accéder aux guides Axiom détaillés dans d’autres langues.
QUICK START
3 feet (1 m) per second at 1/2 inch (1.25 cm) above ground
Power ON. Set Sensitivity,
Threshold and Volume. Perform Frequency Scan (if needed to eliminate EMI).
Ground Balance
(if needed to
eliminate ground
response).
Begin
scanning.
Lengthen lower stem
until it snaps into place.
Adjust upper stem.
BATTERY CHARGING
12V battery terminal charging with optional
cables. Charge time: 10 hours approx.
ADJUSTING ARM CUFF
Use hexnut wrench
(stored below cu)
to remove four
screws.
Move cu up to
two slots forward
or backward (at
least 2 bolts must
be secured).
Clip Axiom Booster Pack into the
stand below the detector cu.
Axiom Booster pack uses eight
(8) AA akaline or NiMh batteries.
Note proper polarity direction.
P
Use supplied 3-amp USB wall charger.
Charge time: 7 to 8 hours approx.
Plug cable into the USB
connector on back of
Axiom.
       

1. Power and Factory Reset—Hold 1 second for power ON or OFF. Press and hold 5 seconds
to restore Factory Settings. Tap to exit MENU settings.
2. VOLUME Plus/Minus buttons—Use to increase / decrease detector volume.
3. SENSITIVITY Plus/Minus buttons—Use to increase / decrease Sensitivity setting. These
buttons are also used while adjusting MENU settings.
4. MENU/Iron Check— Repeatedly press to scroll through Menu items, then use the Plus
(+) or Minus (-) buttons above MENU to change setting. Press and hold button to use Iron
Check function.
5. THRESHOLD Plus/Minus—Use to adjust the background audio hum that is added to
target response.
6. Ground Balance—Hold down while bouncing coil above ground until ground response
disappears or becomes as small as possible.
1
2
3
4
5 6 7 8 9
10
1112
1314
15
1. Signal Strength Indicator—indicates both signal strength and polarity.
2. Iron Check—Indicates that Axiom’s Iron Check feature is in use.
3. Mode—Select from Fine, Normal, Large or Salt.
4. Frequency Scan—To overcome EMI, highlight FREQ SCAN on Menu, and press Plus (+) Menu
button to begin the scan. Takes approximately 45 seconds.
5. Tone—Scroll through 00 to 99 to select your preferred audio tone.
6. Audio Type—Select 00 for PWM audio or 01 for VCO audio..
7. Sensitivity—Indicates current Sensitivity setting.
8. Battery Level—Shows status of battery life (25% per segment).
9. Speed—Select Slow, Medium or Fast detection speed.
10. Ground Track—Select O, Slow, Medium or Fast continuous ground tracking speeds.
11. Backlight—Indicates LCD Backlight is on.
12. Wireless headphones—Press Plus (+) Menu button to pair to headphones or Minus (-) to
unpair. Icon ashes while attempting to pair; is solid when unit is paired with headphones.
13. Gnd Balance Arrows—Indicates trending direction of ground balance when Gnd Track is on.
14. Gnd Balance Indicator—Displays while performing ground balance.
15. Ground Balance Values—are shown by the upper and lower 2-digit numbers.
1
2
34 5 6
CONTROLS LCD/DISPLAY ELEMENTS
FACTORY DEFAULT SETTINGS
Sensitivity: 6
Volume: 24
Threshold: 15
Mode: Fine
Frequency: 50
Tone: 50
Audio: 01(VCO)
Ground Balance: 49/49
Wireless: O
Backlight: O
Speed: Medium
Ground Track: O