Gate X-ASR User manual

Last update on MARCH 19, 2019 www.gatee.eu
USER GUIDE

Information contained in this document is subject to updating without notice.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE INSTALLING THE DEVICE
THE DEVICE COVER MUST NOT BE REMOVED BY THE USER
Notice
Safety Summary
DANGER!
FOR YOUR SAFETY
USER GUIDE
02 WWW.GATEE.EU
GATE Enterprise Sp. z o.o. Sp. K. does not take any responsibility for damages,
injuries and accidents resulting in the use of this product or the use of Air Electric
Gun with the product installed.
Caution must be exercised to prevent short circuiting the battery as the
consequences can be very dangerous.
We recommend that this product should be installed by an experienced airsoft
service.

CERTIFICATE OF CONFORMITY
PRODUCT DISPOSAL INSTRUCTIONS
NOTE:
USER GUIDE
03
WWW.GATEE.EU
WARNING: Before starting installation process, please ensure that your AEG is
empty and there are no BBs inside.
In case you have any difficulties while installing or using this product, we
recommend to email us at [email protected].
Please check if you have downloaded the latest manual from the Technical Support
section of our website: www.gatee.eu. The Product Warranty Form is also available
there.
The symbol shown here means that the product is classed as Electrical or Electronic Equipment
and should not be disposed with other household and commercial waste at the end of its
working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/UE)
has been put in place to recycle products using best available recovery and recycling
techniques to minimize the impact on the environment. Purchasers shall take any old electrical
equipment to waste recycling public centers or points of sale.
EC DIRECTIVE 2011/65/EU
GATE Enterprise Sp. z o.o. Sp. K. hereby declares under our sole responsibility that the product
GATE X-ASR is in conformity with the essential requirements of the following Directives:
This product has been certified as RoHS Compliant.

Table of Contents:
04 WWW.GATEE.EU
• Scheme............... ................................................................................................
03. Troubleshooting....................................... ...........................................................
Safety Summary .......................................................................................................
Table of Contents ......................................................................................................
01. Overview .............................................................................................................
• Key Functions ......................................................................................................
04. GATE Limited Warranty Policy ...........................................................................
• Installation of X-ASR without replacement of wires............................................
• AEG standard installation diagram ......................................................................
02. Installation ...........................................................................................................
2
8
5
5
9
7
7
4
6
7
USER GUIDE

01. Overview
05
WWW.GATEE.EU
Key Functions
MOSFET
Debouncing (Digital Interface)
We introduce the world’s first 4th generation mosfet. X-ASR is a highly reliable AEG
controller. It has automatic resettable protection against battery reverse polarity,
SMART FUSE and built-in self-test. It does not require additional fuse in AEG
installation.
Do you want to achieve higher rate of fire and faster trigger
response? Are you planning power upgrade of your rifle? In that case,
you need a MOSFET.
It targets the energy from the battery directly to the motor,
bypassing the mechanical trigger contacts. As a result, you gain a
higher rate of fire of the rifle and faster trigger response, and the
contacts are protected against burn out.
This provides full compatibility with the micro-switches. It is fully
resistant to contact bounce. You gain a bigger ROF, a faster trigger
response and your MOSFET is less prone to heating.
USER GUIDE
Built-In Self-Test
It allows you to quickly check whether the AEG controller works
properly. If you have problems with your AEG, the BUILT-IN SELF-TEST
allows you to check that the problem is not caused by the controller.

06 WWW.GATEE.EU
USER GUIDE
Coating
Thanks to its special conformal coating, it is resistant to atmospheric
conditions (Military Specification MIL-V-173C).
Trigger wire TERMINAL
AEG
Connectors
Battery
connector
LED
indicators
Motor POSITIVE TERMINAL (+)
Motor NEGATIVE TERMINAL (-)
Scheme
3 pcs. of 3.2x18mm [0.126x0.71 inch] heat-shrink tubes
1 pc. of 445mm [17.52 inch] of 16 - 22 AWG wire
For installation you will need:
3 pcs. of 2.8x0.5mm female terminals

02. Installation
Fig 1. Standard AEG wiring scheme
BATTERY
UP TO 12.8V
AEG Motor
A B
CONTACTS
C
To adapt the standard AEG installation to work with X-ASR it is necessary to get to
the trigger contacts. In case of GB v2 contacts are located inside a gearbox. With a
version 3 gearbox, the installation will be easier because the contacts are outside of
the gearbox. Please consult a local airsoft technician if you have never
disassembled a gearbox before or if you have any installation concerns.
a) Installation of X-ASR without replacement of wires. Using this method, the
original wiring is kept intact, and the connections are modified. Referencing
Fig 1., de-solder A wire from the one of the trigger contacts and then solder it to the
B wire. It does not matter which wire you disconnect from the trigger switches, just
join the two wires together at one terminal. In the place of the A wire, solder the
additional single signal wire. The trigger wire can be very thin because it handles
very low current and it is only used for switch-detection.
USER GUIDE
1.
AEG Motor
CONTACTS
BATTERY
UP TO 12.8V
07
WWW.GATEE.EU

USER GUIDE
03. built-in self-test
08 WWW.GATEE.EU
Overload - temperature too high,
X-ASR is designed up to M120 spring

06. GATE Limited Warranty Policy
1. This Limited Warranty is valid provided that the owner provides a proof of
purchase and properly completed warranty form.
2. This Limited Warranty does not cover: (a) defects or damage (eg. mechanical,
thermal or chemical) resulting from accident, misuse (misinterpretation of the
instructions), abuse, neglect, unusual physical, electrical or electromechanical
stress, water immersion, repairs or structural modification of any part of Product
(eg. heat-shrink tube removal), or (b) the Product that has the serial number
removed or made illegible; (c) defects or damage from improper operation,
maintenance or installation, (d) installation of the products.
GATE Enterprise Sp. z o.o. Sp. K. warrants that its Product is free from
manufacturing and material defects at the date of purchase and for a period of two
(2) year from the date of purchase and it is not-extendable. This Limited Warranty is
conditioned upon proper use of Product by Purchaser.
Contact: [email protected]
3. Requests for warranty are processed as soon as possible, not exceeding seven
(7) working days. The company's obligation under this Limited Warranty shall be
limited to providing replacement of part/s only.
USER GUIDE
09
WWW.GATEE.EU