GE APFD06 Operating instructions

Write the model and serial
numbers here:
Model #_________________
Serial # _________________
Find these numbers on a label on
the side of the air conditioner.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
OWNER’S MANUAL
AND INSTALLATION
INSTRUCTIONS
AIR CONDITIONER
Portable Room
49-5000527 Rev. 2 10-21 GEA
APFD06
IMPORTANT SAFETY
INFORMATION ............. 3
CONTROLS .................4
CARE AND CLEANING ....... 7
INSTALLATION
INSTRUCTIONS ............. 9
TROUBLESHOOTING ....... 14
LIMITED WARRANTY ........15
CONSUMER SUPPORT .......16

249-5000527 Rev. 2
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GEAppliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.

49-5000527 Rev. 2 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING To reduce the risk of fire, electrical
shock, injury to person or damage when using the air
conditioner, follow basic precautions including the
following:
• Read all of the instructions before using this
appliance.
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Do not operate the air conditioner if it has a damaged
cord or plug or not working properly or if it has been
damaged or dropped.
• The air conditioner should be serviced only by
qualified service personnel. Call an authorized
service company for examination, repair or
adjustment.
• Disconnect power before servicing.
• Disconnect power before cleaning.
NOTE: Turning off power by pressing the Power button
does NOT disconnect the appliance from the power
supply.
• Do not install or use the air conditioner in any area
where the atmosphere contains combustible gases
or where the atmosphere is contaminated. Avoid any
chemicals coming in contact with your air conditioner.
• Do not store anything directly on top of the air
conditioner.
• Two or more people are required move and install air
conditioner.
• Never operate the air conditioner without filters in
place.
• Do not use air conditioner near a bathtub, shower or
wash basin or other wet area.
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
IMPORTANT SAFETY INFORMATION
WARNING How to Insert the Batteries in the Remote Control
• Remove the battery cover by sliding it according to
the arrow direction.
• Insert new batteries, making sure that the (+) and (-)
of battery are installed correctly.
• Reattach the cover by sliding it back into position.
NOTES:
• Use 2“AAA”(1.5 volt) alkaline batteries. Do not use
rechargeable batteries.
• Remove the batteries from the remote control if the
system is not going to be used for a long time.
• Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc) or rechargeable (ni-
cad, ni-mh, etc) batteries.
WARNING Caution for ingestion. The battery may cause suffocation if swallowed by children.

449-5000527 Rev. 2
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
NOTE: When the machine is powered on for the first
time, the buzzer will play power-on music and then the
machine will go into standby status.
1. Power Button
Turns ON/OFF power to the air conditioner.
NOTE: Turning off power by pressing the Power
button does NOT disconnect the appliance from
power supply.
Press the Power button. The power indicator and
temperature display will illuminate, select desired
settings, after one minute the Display lights will turn off.
Press any button on the unit or remote, the display
will illuminate. Then press corresponding buttons to
change unit function.
Note: If changing functions from remote, it may
require multiple button pushes to synchronize remote
to the unit.
2. Mode Button
Press the Mode button to toggle among the operating
options. The corresponding indicator will illuminate:
Cool – Cools the room to the set temperature
Dry – Reduces the humidity in the room
Fan – Circulates the air in the room without cooling
3. + and – Buttons
Sets the Temperature when in Cooling Mode or sets
the Time when Timer is selected.
To Set the Temperature:
Press the +or –button to select the required
temperature.
NOTE: The temperature cannot be set when the air
conditioner is in either Fan or Dry mode.
To Set the Time:
Press the +or –button to select the required time.
4. Fan Speed Button
The fan speed can be adjusted from Low to High speed
when the air conditioner is in operation.
NOTE: The fan speed cannot be adjusted when the unit
is in Dry mode.
5. Timer Button
Program a time from (1 hour to 24 hours) for the air
conditioner to turn Off or On.
6. Sleep Mode
Press the Sleep button to turn on Sleep Mode.
NOTE: You cannot turn on the Sleep mode in the Dry or
Fan Mode.
NOTE: When the inner unit chassis is full of water, the
Water Full light will turn on. A buzzer will sound for several
seconds and the compressor will stop.
Refer to the instructions on page 5 for draining the water from
the unit.
Controls
USING THE AIR CONDITIONER
5 4
Power
Mode
Sleep
Fan
Timer
Low
High
Timer
Water Full
Power
Cool
Fan
DrySleep
3 6 2 1

49-5000527 Rev. 2 5
Controls
Frost Protection Function:
In cooling or dry mode, if the temperature of the exhaust
hose is too low, the AC will automatically go into a
unit protection state. When the temperature rises to a
normal temperature, the unit will automatically resume
normal operation.
Overflow Protection Function:
When water in the water pan exceeds the warning level,
the machine will automatically sound an alarm, the FULL
indicator light will flash and the unit will shut down. At
this point, you need to drain the water from the lower
drain (See Drainage instructions for details)
After the water is emptied, the machine the machine will
automatically resume normal operation.
Automatic Defrosting (on some models)
The machine has an automatic defrosting function.
Protection Function of the Compressor
To increase the service life of the compressor, the AC
has a 3-minute delay after the compressor has shut off to protect the compressor.
The display will always default to show room temperature.
When the air conditioner is turned on, it will automatically start in the last mode and fan settings selected.
USING THE AIR CONDITIONER
Drainage Instructions
Draining the unit manually:
Note: Please move the AC carefully, do not spill the
water in the water pan at the bottom of the unit.
1. When the AC stops after the water is full, turn off the
AC power and unplug the power plug.
2. Place a water container larger than the sump
capacity (at least 1-1/2 quart) below the lower rear
water outlet on the back side of unit.
3. Remove the plug, the water will automatically flow
into the container.
Note: During drainage, the body can be tilted slightly
backwards. If the water container cannot hold all the
water, before the water container is full, replace the water
plug as soon as possible to prevent water from flowing to
the floor or the carpet.
4. After water has been drained from the unit, re-install
the water plug securely.
Note: Restart the AC after the water plug is installed,
otherwise condensate water from the AC will drain onto
the floor or carpet.
Continuous drainage (optional, and only in dry mode)
1. Remove the upper drain plug.
2. Connect a drain hose with an inside diameter of 5/8”
to the water outlet.
3. Route drain hose to a bucket or floor drain.
4. Be sure to use a large container (3 gallons or larger
is recommended) and monitor the water level in the
container continuously. The unit will not shut off when
the container is full. An overflowing container can
cause flooding and damage to the floor.

649-5000527 Rev. 2
Controls
USING THE AIR CONDITIONER
Features and appearance may vary.
Icons on the remote control indicate the selected settings REMOTE CONTROL
1. Insert the two AAA batteries (provided).
2. Aim the remote control at the signal receiver on the
control panel to operate the air conditioner.
A. Power Button
Turns ON/OFF power to the air conditioner.
B. Mode Button
Press the Mode button to toggle among the operating
options, cooling, fan and dry mode.
C. + and – Button
Adjusts the Temperature or Timing set value.
D. Fan Button
Press the Fan button to adjust fan speed from Low to
High speed.
E. Timer
Press Timer button to activate the ON/OFF timer. Use
the +and –buttons to adjust the timer.
F. Sleep Button
Press the Sleep button to turn on the sleep mode.
Note:7KHDLUFRQGLWLRQHU/('GLVSOD\ZLOOWXUQRႇ
minute after last button is pushed. To turn on LED
display, press any button on the unit or the remote.
Then press control corresponding function to change
the settings, the remote may require multiple pushes to
synchronize with the unit.
CA
B
F
D
E

49-5000527 Rev. 2 7
Care and Cleaning
CARE AND CLEANING
Cleaning the surface
Clean surface of machine with a wet soft cloth. Do not
use chemicals, such as benzene, alcohol, gasoline,
etc.; otherwise, the surface of the air conditioner will be
damaged or the entire unit will be damaged.
CLEANING 1. Unplug or disconnect power.
2. Use only a soft cloth dampened with water to clean
the cabinet.
NOTE:
•Do not use a liquid or spray cleaner to clean the air
conditioner.
•DO NOT use chemicals, abrasives, ammonia,
chlorine bleach, concentrated detergents, solvents or
scouring pads. Some of these chemicals/items may
damage and/or discolor your air conditioner.
3. Dry thoroughly with a soft cloth.
4. Plug in or reconnect power.
WARNING
Electrical Shock Hazard
Disconnectpowerbeforecleaning.
Air Filter
The air filters should be cleaned at least every two
weeks for your unit to operate at optimum efficiency.
CAUTION DO NOT operate the air conditioner
without a filter because dirt and lint will clog it and
reduce performance.
To clean the upper filter screen frame:
1. Remove the upper and lower filter screens. On the
top filter, place finger in recess at top of filter and
pull down and outward to remove. On the lower filter,
place finger in recess at bottom of filter, pull upward
and outward to remove filter.
2. Remove the filter from the filter frame. It is held in
place by 4 tabs. After removal, wash or vacuum the
filter to remove the dirt and lint. Make sure filter is dry
before reinstalling on the unit.
Storage
If the unit is not being used for a long period of time:
To Empty the Internal Water Tank:
1. Unplug or disconnect power.
2. Drain the water from the water tank. (See “Internal
Water Tank section” above.)
3. Use the original packaging to repack the unit to avoid
a buildup of dust or dirt.
4. Store the air conditioner in a cool, dry location.

849-5000527 Rev. 2
Installation Instructions
Location Requirements
• Place the air conditioner on a flat, level surface in a
location that is at least 20” (50 cm) from any wall.
NOTE: A minimum clearance of 20” (50 cm) from
the air conditioner to the wall must be maintained to
ensure proper airflow.
• Maintain a minimum 20” (50 cm) clearance around
the air conditioner to not block airflow.
• Keep the air conditioner free of any obstructions
such as drapes, curtains, blinds, etc.
• The exhaust hose should be free of any
obstructions.
• Do not place the air conditioner on an unstable
or raised surface because it could fall and cause
damage or injury.
• Do not place the air conditioner in direct sunlight
or near a heat source such as baseboard heaters,
stoves, etc.
• The window panel can be installed in a window with
a minimum 20” (50.8 cm) to a maximum 48” (121.9
cm) opening.
INSTALLATION INSTRUCTIONS
Questions? Call GE Appliances at 866.907.1655 or visit our Website at: GEAppliances.com.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT —Save these instructions for
local inspector’s use.
•IMPORTANT —Observe all governing codes
and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
•Completion time – Approximately 1 hour
• We recommend two people to install this product.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
• You MUST use all supplied parts and use proper
installation procedures as described in these
instructions when installing this air conditioner.
ELECTRICAL REQUIREMENTS
These models require a 115/120-volt AC,
60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility
of electric shock hazard. If the wall outlet you plan to
use is only a 2-prong outlet, it is your responsibility
to have it replaced with a properly grounded 3-prong
wall outlet.
CAUTION
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Do not change the plug on the power cord of this air
conditioner.
Aluminium house wiring may present special
problems—consult a qualified electrician.
Power cord includes a current
interrupter device. A test and reset
button is provided on the plug case.
The device should be tested on
a periodic basis by first pressing
the TEST button and then the
RESET button while plugged into
the outlet. If the TEST button does
not trip or if the RESET button will
not stay engaged, discontinue use
of the air conditioner and contact a
qualified service technician.
RESET
TEST

49-5000527 Rev. 2 9
PARTS INCLUDED
(Appearance may vary)
1. Top Cover
2. Control Panel
3. Side Panel
4. Air Outlet / Louver
5. Front Housing
6. Rear Housing
7. Caster
8. Base Pan
9. Upper Filter
10. Upper Continuous Drain
11. Cord Wrapping Post
12. Exhaust Air Vent
13. Lower Filter
14. Lower Drain
INSTALLATION INSTRUCTIONS
Installation Instructions
21
3
7
8
5
49
6
10
12
11
13
14

Exhaust Hose Assembly
Remote Control
Batteries (2) Phillips head screwdriver (Not Included)
TOOLS YOU WILL NEED
Window Mounting Kit 1 pc – 20” Center Panel
SF±ï»๜´(QWHQVLRQ
1 pc – 9” Extension
2 pc – 16” Extensions
Pointed Screws (7)
2 – Top Window Bracket
1 – Security Bracket
4 – Main Window Panel
Security BracketBottom Window Bracket (2)Top Window Bracket (2)
Top Foam Strip
Bottom Foam Strip
Foam Strip
Flat Tip Screw
For exhaust nozzle to
main window panel.

10 49-5000527 Rev. 2
INSTALLATION INSTRUCTIONS
Installation Instructions
Window Panel Combinations to fit window openings
(Appearance may vary)
Window Opening 20”
Center Panel Only
:LQGRZ2SHQLQJ´ï»๜´
&HQWHU3DQHOï»๜´([WHQVLRQ
:LQGRZ2SHQLQJï»๜´´
Center Panel + 9” Extension
:LQGRZ2SHQLQJï»๜´ï»๜´
&HQWHU3DQHO´DQGï»๜´([WHQVLRQV
:LQGRZ2SHQLQJï»๜´´
Center Panel + 16” Extension
Window Opening 34”- 41”
Center Panel + 9” and 16” Extensions
Window Opening 41”- 48”
Center Panel + (2) 16” Extensions