GE JGP633 User manual

Istallatio
Istructio s 36"SealedGasCooktop
JGP633, JGP970, PGP966, ZGU36
i Ouestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
r_ In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca i
IN THE COMMONWEALTH OF
MASSACH USETTS:
, This product must be installed by a licensed
plumber or gas fitter.
, When using ball-type gas shut-off valves, they
shall be the T-handle type.
, A flexible gas connector, when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
.IMPORTANT -Savetheseinstructions
for local inspector's use.
. IMPORTANT - Observeallgoverning
codes and ordinances.
, Note to Installer- Be sure to leave these
instructions with the Consumer.
Note to Consumer - Keep these instructions for
future reference.
, Product failure due to improper installation is not
covered under the Warranty.
WARNING -Thisappliancemust be
properlygrounded.
.IMPORTANT - Leak testingofthe
applianceshallbe conducted accordingto the
manufacturer's instructions.
, Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
WARNING - Disconnectallelectrical
power at the main circuit breaker or fuse box
before installing.
FOR YOUR SAFETY:
A WARNING - If the information in this
manual is not followed exactly, a fire, explosion
or gas leak may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
Do not install this product with an air curtain hood
or other range hood that operates by blowing air
down on the cooktop. This airflow may interfere
with operation of the gas burners resulting in fire or
explosion hazard.
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance. Do not touch
any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
, If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
This cooktop has been design certified by CSA
International. You'll find safety precautions in your
Owner's Manual.
Read them carefully.
Installation of this cooktop must conform with
local codes or, in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest edition.
, Be sure your cooktop is installed properly by a
qualified installer or service technician.
, To eliminate reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-10861 (07-12 GE) 1

Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as noted on the rating plate.
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician
show you where your main cooktop disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
cooktop according to governing codes could result
in a hazardous condition.
If there are no codes, your cooktop must be wired
and fused to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70--Latest edition.
You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada your cooktop must be wired and fused
to meet the requirements of the Canadian Electrical
Code.
Be sure the installation of this product in a mobile
home conforms with the Manufactured Home
Construction and
Safety Standard, Title 24 CFR, Part 3280.
If this standard does not apply, you must follow
the standard for Manufactured Home Installations,
ANSI A225.1 and Manufactured Home Installations,
Sites and Communities and ANSI/NFPA 501A or
with local codes.
You can get a copy of the Federal Standard by
Writing:
Office of Mobile Home Standards
HUD Building
451 7th Street, S.W.
Washington, D.C. 24010
PARTS INCLUDED
2 Screws Foam Tape
(GlassTop
Models Only)
2 Hold
Down Brackets
MATERIALS YOU MAY NEED
Joint Sealant Pipe Fittings Shut-Off Valve
CSA-Approved Flexible Gas Line
3/8" Min. ID, 1/2" NPTConnection,
3-foot Maximum Length (Massachusetts Only)
TOOLS YOU WILL NEED
FOR INSTALLATION
Pencil
Phillips-Head
Screwdriver
Ruler or Straightedge
Safety Glasses
SaberSaw
Pipe Wrench
!/8" Drill Bit & Electric or
Hand Drill

Installation Instructions
PRE-INSTALLATION CHECKLIST
[Z]
@
When preparing cooktop opening, make
sure the inside of the cabinet and the
cooktop do not interfere with each other.
(See section on preparing the opening.)
Remove packaging materials, grote boxes,
regulator with literature, and literature
package from the cooktop before beginning
installation.
_-_ Literature PockOgGrot e boxes
E1 Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and Care,
Installations, etc. in a safe place
for future reference.
El
El
FF1
[]
Hake sure you have all the tools and
materials you need before starting the
installation of the cooktop.
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to section
on electrical requirements.)
When installing your cooktop in your home,
make sure all local codes and ordinances
are followed exactly as stated.
Hake sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated by
the cooktop.

Installation Instructions
PREPARING THE OPENING
r_ MAINTAIN THE FOLLOWING
MINIMUM CLEARANCE DIMENSIONS
13" MAX. Depth of unprotected
overhead cabinets _ 6" MIN. clearance from
cutout to side wall on the
right of the unit
30" MIN. clearance from countertop
to unprotected overhead surface
18" IVllN.height
from countertop to
nearest cabinet on
either side of unit
3-3/4" MIN.clearance from
cutout to side wall on the
left of the unit
NOTE: Allow 7/16"
minimum vertical
clearance from the
cooktop bottom (or
3-5/8" minimum depth
from the countertop)
to any combustible
surfaces, such as a
cabinet drawer.
For island installation,
maintain 2-1/2 in.
J:
3-5/8" -f
7/16"
DRAWER
]
minimum from cutout to front and back edge of
countertop. Maintain 3 in. minimum from cutout to
side edges of countertop.
E_ OVERALL COOKTOP DIMENSIONS
, 21" (21-1/4" Max. for
_ _'__3-11/1B" Model ZGU3B)
18-7/8" ._._
F_ CUTOUT DIMENSIONS OF
COUNTERTOP
To ensure accuracy, it is best to make a template
when cuttinq the openinq in the counter.
___19-1/_' width cut
7._ _ ss-7/8"_-c'_ -__
length _ 16-15/16"
2-1/4" Min. Between of cutcutout and the wall
behind the cooktop
2-1/2" Min. from
front edge of cutout
and front edge of
countertop
RECOMMENDED GAS SUPPLY
LOCATION FROM BACKWALL
Recommended
gas supply
location
1" Min. From Backwall
From Cutout
Center Line
I_] MAKE SURE WALL COVERINGS,
COUNTERTOP AND CABINETS
AROUND COOKTOP CAN
WITHSTAND HEAT (UP TO 200°F)
GENERATED BY COOKTOP
Wall covering,
cabinets and
countertop must
withstand heat
up to 200°F
FOR AMERICANS WITH DISABILITIES
ACT (ADA) FORWARD APPROACH
INSTALLATION ON LY:
Allow 5" minimum
depth between the
countertop and an
enclosure.
Y
IL
NOTE: The enclosure must be made of wood
material. Also, an access panel is required for the
electrical outlet, pressure regulator, shut-off valve,
hold-down brackets, and service.

Installation Instructions
iNSTALLiNG THE COOKTOP UNiT
rT] LOCATE ELECTRICAL OUTLET AND
GAS SHUT-OFF VALVE BENEATH
CABINET
NEVER REUSEOLD
CONNECTORS WHEN
INSTALLING THIS
UNIT.
H I
_1LS
I1 k'
Shut-Off I\
_Lj Valve _ tElectrical
tt Outlet 12"
tBelow
Countertop
Install a manual shut-off valve in the gas line in an
easily accessible location outside the cooktop. Be
sure you know how and where to shut off the gas
supply to the cooktop. Install the electrical outlet
12" below the countertop.
PROTECT SURFACE OF COOKTOP
Place a towel or tablecloth onto the countertop.
Lay the cooktop upside down onto the protected
surface.
Bottom of cooktop
Cloth under Cooktop
r_ ATTACH FOAM TAPE
(glass maintop models only)
Apply the foam tape around the outer edge
of the glass. Do not overlap the foam tapes.
Bottom of Cooktop
.\_ Foam Tapes
Cooktop Glass
_-] LOCATE MOUNTING PARTS
Remove the hold-down brackets from the literature
package.
iTi ATTACH BRACKETS TO COOKTOP
Remove the screw from the bottom of the cooktop
and screw the hold-down bracket
to the side of the cooktop unit. Repeat for opposite
side of cooktop.
Bottom
of Cooktop
--_..
Pre-drilled
Foam Tapes
Cooktop
Glass
F6] INSERT COOKTOP INTO CUTOUT
Insert the cooktop centered into the cutout opening.
Make sure the front edge of the countertop is
parallel to the cooktop. Make final check that all
required clearances are met.
Once the unit is in place, screw the hold-down
bracket into the cabinet sides to secure the unit
into place.

Installation Instructions
INSTALLATION--GAS CONNECTIONS
r_ PROVIDE ADEQUATE
GAS SUPPLY
This cooktop is designed to operate on natural gas
at 4" of water column manifold pressure and 7" of
water column (W.C.) supply pressure. It is shipped
from the factory set for natural gas. The convertible
pressure regulator supplied with the unit must
be connected in series with the manifold of the
cooktop and must remain in series with the supply
line regardless of whether natural or LP. gas is
being used.
FOR PROPEROPERATION, THE MAXIMUH INLET
PRESSURETO THE REGULATOR MUST BE NO HaRE
THAN 14" OF WATER COLUMN PRESSURE.For
checking the regulator, the inlet pressure must
be at least 1" W.C.. (or 3.4 KPA) greater than the
regulator output setting. If the regulator is set for 4"
W.C. of water column pressure, the inlet pressure
must be at least 5" W.C. If the regulator is set for
10" W.C., the inlet pressure must be at least 11"
W.C.. The gas supply line to the cooktop should be
1/2" or 3/4" pipe.
J_ INSTALL REGULATOR
NEVER REUSEOLD CONNECTORS WHEN
INSTALLING THIS COOKTOP.
A WARNING: Neverreuseold
flexible connectors. The use of old flexible
connectors can cause gas leaks and personal
injury. Always use new flexible connectors when
installing a gas appliance.
Screw a section of pipe onto
the inlet end of the pressure
regulator and install the
coupling. Pressure __[_
Regulator
Coupling
To reduce the likelihood of gas leaks, applyl-_lon
tape or a thread compound approved for use with
LP or Natural gases to all threaded connections.
r_ INSTALL REGULATOR ONTO
BURNER BOX BOTTOM
Screw the regulator
onto the burner
box bottom pipe
connection.
Hake sure the
top of the regulator
is facing towards the
cabinet front, easily
accessible through
the cabinet doors.
I
I
Pressure ___
Regulator
Coupling _l
Shut-Off
_l Valve _'_
l]J
U
1 Electrical
I Outlet 12"
I Below
Countertop
_] COMPLETE CONNECTION WITH A
COUPLING
Complete the
connection between
the regulator, pipe
coupling, and
the shut-off valve.
I
I
Pressure
Regulator
Coupling _l _
Shut-Off
Valve
Jw
Ll
i\
II Electrical
I Outlet 12"
I Below
Countertop

Installation Instructions
CHECK FOR LEAKS
Before testing for leaks, make sure all burner knobs
are in the OFF position.
After connecting the cooktop to gas, check system
for leaks with a manometer. If a manometer is not
available, turn the gas supply on to the cooktop
and use a liquid leak detector at all joints and
connections to check for leaks.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
DO NOT USE OPEN FLAME TO CHECK FOR
LEAKS!
Disconnect the cooktop and its individual shut-off
valve from the gas supply piping system during any
pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa).
Isolate the cooktop from the gas supply piping
system by closing its individual shut-off valve
during any pressure testing of the gas supply
system at test pressures equal to or less than
1/2 psig (3.5 kPa).
_] INSTALLATION OVER
BUILT-IN OVEN
See built-in oven installation for complete
installation instructions.
iT
_1 ToCenterof
|I_ 2" Dia. Hole From
_ Countertop
90°E,bowj_t_ I-TT] _:_
jl_-_,_ 2" Dia. Hole
1207/8" from front
of Countertop to
Hole Center)
Cabinet Sides -__ ,

Installation Instructions
INSTALLATION--ELECTRICAL CONNECTIONS
WARNING - Disconnectallelectrical
power at the main circuit breaker or fuse box
before installing.
r_ EXTENSION CORDS
Because of potential safety hazards under certain
conditions, we strongly recommend against the
use of an extension cord. However, if you still
elect to use an extension cord, it is absolutely
necessary that it be a UL listed 3-wire grounding
type appliance extension cord and that the
current carrying rating of the cord in amperes be
equivalent to or greater than the branch circuit
rating. Such extension cords are obtainable
through your local appliance dealer.
IMPORTANT: (Pleaseread carefully)FOR
PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
[Z] ELECTRICAL SUPPLY AND OUTLET
An adequate electrical supply and outlet must
be used to operate the electrical parts of your
cooktop.
[] The power cord of this appliance is equipped
with a 3-prong (grounding) plug which must
be used with a properly grounded 3-hole
outlet with a standard 120 Volt, 60 cycle AC
household current.
If you do not have a 3-hole grounded outlet,
have a qualified electrician change your old
one.
[] A grounding adaptor will be needed to convert
the old one until the outlet can be replaced.
This method is only temporary, and a qualified
electrician should test it to be sure it meets
requirements.
Ensure proper
ground and
firm connection
before use
TWO-PRONG WALL RECEPTACLE
Where a standard 2-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with
a properly grounded 3-prong wall receptacle.
Do not under any circumstances cut or remove
grounding prong from the cooktop cord. Failure
to provide proper polarization may create a
hazardous condition.

Installation Instructions
USAGE SITUATIONS WHERE
APPLIANCE POWER CORD
WILL BE DISCONNECTED
INFREQUENTLY
For 15 amp circuit only. Do not use an adaptor
on a 20 amp circuit. Where local codes permit, a
TEHPORARY CONNECTION may be made to a properly
grounded two-prong wall receptacle by the use of a
UL-listed adaptor available at most hardware stores.
The larger slot in the adaptor must be aligned with
the large slot in the wall receptacle to provide proper
polarity in the connection of the power cord.
Ensure proper ground and firm
connection before use
Alignlarge
prongs/slots
Temporary Method
(Adaptor plugsnot permitted inCanada)
A CAUTION: Attachingthe adaptor ground
terminaltothe wallreceptaclecoverscrew does not
ground the applianceunlessthe screw ismetal,and
notinsulated,and the wallreceptacleisgrounded
through the house wiring.The customer should have
the circuitchecked by a qualifiedelectricianto make
surethe receptacleisproperlygrounded.
When disconnecting the power cord from the
adaptor, always hold the adaptor with one hand. If
this is not done, the adaptor ground terminal is very
likely to break with repeated use. Should this happen,
DO NOT USE the appliance until a proper ground has
again been established.
Usage situation where appliance power cord will be
disconnected frequently.
Do not use an adaptor plug in these situations
because disconnection of the power cord places
undue strain on the adaptor and leads to eventual
failure of the adaptor ground terminal. The customer
should hove the 2-prong receptacle replaced with
a 3-prong (grounding) receptacle by a qualified
electrician before using the appliance.

Installation Instructions
COOKTOP BURNERS
r_ ASSEMBLING THE COOKTOP
BURNERS
The electrode of the spark igniter is exposed. Be
careful not to push any cooktop controls while the
top of the burner is removed.
Do not remove the top or touch the electrode
of any burner while another burner is turned on.
Electrical shock might result.
DReplace the burner head onto the burner
base, making sure that the head is properly
oriented over the burner base and the
electrode. Make sure to place
the correct burner head on the correct burner
base and that the burner head sits level on
the burner base. The burner heads are not
interchangeable.
B] Place the burner
caps on the burner
heads, making sure
to place the correct
burner cap on the
correct burner
head. The burner
caps are not
interchangeable.
Make sure that the
burner caps are
properly seated on
the burner heads.
Burner cap properly seated
Burner cap not properly seated
E] lake sure the pins in
the burner heads
match the burner
base indentations
and that they are
properly seated in
them by rotating the
heads until they are
level.
lake sure the slot in
the burner head
is positioned
over the
electrode. The
burner cap has
three to four
pins. When
replacing the
cap, make
sure none of
the pins sits
in the stability
chamber.
Burner cop
Burner head
,d,..i.- Electrod e
Locator i_i
__Burner
Pin base
indentations
chamber .... Electrode
Burnerbase
Make sure the hole Burner cap
in the burner head f/ ",_
assembly is positioned q__j
over the electrode and Burner head
that the burner head is assembly
fully inserted inside the
burner base. A small
gap between the base
and head is normal.
Electrode Burner
base
10

Installation Instructions
[_] CHECK IGNITERS
Operation of the electric igniters should be
checked after the cooktop and supply line have
been carefully checked for leaks and the cooktop
has been connected to the electrical power.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
[] Push and turn a burner valve to the LITE
position. All spark igniters will make a series of
sparks (ticking sounds), but only the burner
turned to LITE will light.
. The burner should light when gas is
available to the burner.
. Once the burner lights, it should be turned
out of the LITE position.
[] Try each valve separately until all burners
have been checked.
[_ BURNER IGNITION
Cooktop Spark Ignition-When you turn the
cooktop knob to LITE,the spark igniter makes a
series of electric sparks (ticking sounds) which light
the burner. During a power failure, the burners will
not light automatically. In an emergency, a cooktop
burner may be lit with a match by following the
steps below.
A WARNING; Lighting gas burners with a
match is dangerous. You should match light the
cooktop burners only in an emergency.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
r_ Light a match and hold the flame near the
burner you want to light. Wooden matches
work best.
r_ Push in and turn the control knob slowly. Be
sure you are turning the correct knob for the
burner you are lighting.
NOTE: If the burner does not light within five seconds,
turn the knob off and wait one minute before trying
again.
[_ THE BURNER FLAMES
Turn each burner on. Flames should be blue in color
with no trace of yellow. The burner flames should
not flutter or blow away from the burner. The flame
should be no less than 1/4" on the lowest setting
and no greater than 1-1/2" on highest setting.
A WARNING; Ifyouattempt to measure
the flame, please use caution.
Burns could result.
1/4"to-'-_ I _ CooktopBumer
1-1/2"
Burners should be checked frequently
r_ BURNER GRATES
The three cooktop grates are designed for
specific positions. For maximum stability, these
grates should only be used in their proper position:
they should not be interchanged. For your
convenience, the undersides of the left and right
grates are marked "OUTSIDE" and "INSIDE". Make
sure that the side marked "OUTSIDE" is on the outer
edge of your cooktop. Make sure that the tabs
on either side of the center grate fit into the slots
located on the "INSIDE" edge
of the side grates.
"INSIDE"
edges
I
"OUTSIDE"edge /_ "OUTSIDE"edge
Tab Tab
11

Installation Instructions
OPERATION CHECKLIST
r_ Make sure all controls are left in the OFF r_
position. Check to be sure the cooktop is in the
UNLOCKED position (on models so equipped).
Make sure the flow of air to and from the
cooktop is unobstructed.
The serial plate for your cooktop is located on
the bottom of the burner box. In addition to the
model and serial numbers, it tells you the ratings
of the burners and the type of fuel and pressure
the cooktop was adjusted for when it left the
factory.
EEl
When ordering parts, always include the serial
number, model number and a code letter to
ensure proper replacement parts.
Recheck Steps:
Double check to make sure everything
in this guide has been completed. Rechecking
steps will ensure safe use of the cooktop.
12

Installation Instructions
MAKING THE LP CONVERSION
IF SOLD OUTSIDE THE U,S, AND CANADA:
A WARNING: ifyouwishtousethisproduct
with Liquefied Petroleum (LP)gas containing greater
than 10% butane, you must purchase a butane
conversion kit. To order, please call 1.888.664.8403 or
1.787.276.4051.
Model Butane Kit #
JGP970 WB28TI0229
ZGU36
PGP966 WB28T10283
JGP633 WB28T10235
TOOLS YOU WILL NEED
FOR LP CONVERSION
Phillips-Head 7mm Nutdriver
Screwdriver
Pliers
No. 15 Torx-Head
Driver
Small Flat-Head
Screwdriver (4mm or
5/52" tip size, 60mm or
Safety Glosses 2-3/8" long)
r_ SAFETY INFORMATION YOU
SHOULD KNOW
The pressure regulator and burner orifices are set
for natural gas. To use LP gas, the regulator and
burner orifices must be converted. The LP orifice
spuds for the cooktop burners are attached to
the regulator along with separate LP conversion
instructions.
A CAUTION: The cooktop, as shipped from
the factory, is set for use with natural gas. If you
wish to use your cooktop with LP gas, you must
first replace the orifices and convert the pressure
regulator.
A WARNING: Thisconversionmust
be performedby a qualifiedinstallerorgas supplier
inaccordance withthe manufacturer'sinstructions
and all codes and requirements of the authority
having jurisdiction. Failure to follow instructions could
result in serious injury or property damage. The
qualified agency performing this work assumes
responsibility for the conversion.
ACAUTION: The following adjustments
must be made beforeturningon the burner.
Failure to do so could result in serious injury. Be
sure pressure regulator has been converted as
described in Step 2.
[2]
B]
E1
ADJUST YOUR COOKTOP FOR USE
WITH LP GAS
Disconnect all electrical power, at the main
circuit breaker or fuse box.
Shut off the gas supply to the cooktop
by closing the manual shut-off valve.
Adjust the pressure regulator, by the following
instructions:
, Unscrew the cap.
, Carefully look at the spring retainer to locate
the NAT or LP position.
Cap Gasket_
N_ LP
NAT, _fE_ L.P./Propone
Position Position
Pressure Regulator
. Turn the spring retainer over by rotating it
90 deg., pull it from the cap, turn the spring
retainer over so that LP is showing, insert it
back into the cap, and then rotate it 90 deg.
into position.
. Screw the cap back onto the regulator and
tighten.
13

Installation Instructions
MAKING THE LP CONVERSION (CONT.)
[]
[]
[]
CHANGE COOKTOP BURNER
ORIFICES
Remove the top grates,
burner caps, and burner
heads.
Remove the spark
igniters from the burner
base (if required to
access the orifices).
Using a No. 15 "Torx"
head driver bit, remove
the screws holding the
burner base in position.
Remove This
,!Assembly
Orifice Spud Located
Through This Opening
Using a 7mm nut driver,
remove the top burner
orifices. These may be
accessed through the
hole in the cooktop.
Burner cap
Burner
Spark igniter base
18,000 BTUBurner
(on some models)
_Burner
Burner head
base
Spark igniter
r_ CHANGE COOKTOP BURNER
ORIFICES (CONT.)
On most burners,
the orifices have a spring-
loaded retaining ring around
the hex head to hold the
orifice in the nut driver during
installation and removal. A
_ etainer
Ring
slight amount of force is required to push the nut
driver down over the ring.
NOTE: For orifices that do not have a spring-
loaded retaining ring, use pliers to hold the orifice
in position during initial thread
engagement or final removal to
avoid dropping the orifice in the
cooktop. Then use the nut driver
to tighten or loosen.
14

Installation Instructions
r_ CHANGE COOKTOP BURNER
ORIFICES (CONT.)
[] Locate the LP orifices attached to the
regulator along with separate LP conversion
instructions. They will have a digit for size,
and a letter for type of gas, on the top or
side. (Important: Save the orifices removed
from the appliance for future use.)
Each orifice will show a series of engraved
marks, (I, II, III, X or none), located on the top.
These marks denote the precise location of each
orifice to the cooktop burner.
0000
15,000 BTU/HR Burner (on some models)
O he 15,000 BTU/HRburner has two orifices with
markings located in the sides only. (Seerating
plate on bottom of appliance).
NOTE: The main orifice is located low in the center
of the burner while the simmer orifice is located
higher behind the center of the burner.
Simmel_
orifice Mainorifice
JGP633
PGP966
JGP970 &
ZGU36K
Main: 99 HXL
Simmer: 34 SL
[]
Install the LP orifices in their precise locations
as noted in the illustrations above.
Return the natural gas orifices to the bracket
and reattach the bracket and the instruction
sheet to the pressure regulator using the
screw removed previously.
Replace the burner bases, heads, caps and
top grates. (NOTE: When re-attachinq the
burner bases to lass to units tiqhten screws
to a maximum of 10 in.-Ibs tar uaueJ.)
15

Installation Instructions
MAKING THE LP CONVERSION (CONT.)
ADJUST BURNER FLAMES
Turn all burners full on and check the flames.
They should be blue in color with some yellow
tipping at the ends of the flame. Foreign
particles in the gas line may cause an orange
flame at first, but this will soon disappear.
NOTE: For the 15,000 BTU/HR burner (on some
models) the cooktop burner knob should be
turned to the setting before the lowest setting.
This will ensure that the entire burner is
operating.
r_ Turn the cooktop burner knob to the lowest
setting while observing the flame.
Adjust the low flame setting using the valve bypass
screw as follows:
Low-setting adjustments must be made with two
other burners in operation on a medium setting.
This prevents the low flame from being set too low,
resulting in the flame being extinguished when
other burners are turned on.
E1 To adjust the flame, remove the knobs. Insert
a screwdriver through the access hole in valve
switch. Engage
adjustment screw in
valve. Refer to the
illustration below that
matches the adjustment
screw location for your
model.
. If the flames were too -_ /
small or fluttered, open /_----_,-- __
the valve more than _._._
the original setting. "_.._
. If the flames blew _.._ _
away from the burner, _s:.s_ c
close the valve more
than the original
setting. /only
rB] Make the adjustment by slowly turning the
screw until flame appearance is correct.
Note: Some models may contain a siliconeshieldwhich
coversthe valve switch and access hole.A flashlight may
be requiredto locate the access hole.To accessthe valve
adjusting screw,push the screwdriver through this shield.
After adjustment, reseat the shield around the switch hub
with your fingers, after withdrawing the screwdriver.
Reseat silicone shield
CORRECT INCORRECT
r_ Testing Flame Stability:
Test 1 - Turn the knob from "HI" to the lowest
setting quickly. If the flame goes out
at the lowest setting, increase the
flame size and test again.
Test 2 = With the burner on the lowest setting,
open and close the cabinet door
under the cooktop. If the flame is
extinguished by the air currents
created by the door movement,
increase the flame height and test
again.
El Flame Recheck:
After the adjustment is made, turn all burners off.
Ignite each burner individually. Observe the flame
at the "HI" position. Rotate the valve to the lowest
setting and be sure that the flame size decreases
as the valve is rotated counterclockwise.
TO CONVERT THE COOKTOP BACK TO NATURAL
GAS, REVERSETHE STEPS UNDER MAKING THE LP
CONVERSION.
Once the conversion is complete and checked
ok, fill out the LP sticker and include your name,
organization and date conversion was made. Apply
the sticker near the cooktop gas inlet opening to
alert others in the future that this appliance has
been converted to LP gas. If converting back to
natural gas from LP, please remove the sticker so
others know the appliance is set to use natural gas.
16

Istructio s
d'i stallati Ta le de cuisson scell
au gaz de 91 cm (36")
JGP633, JGP970, PGP966, ZGU36
Web 8 I'adresse : www.electromenagersge.ca
AVANT DE COMMENCER
Avant de commencer, lisez attentivement la totalit6
de ces instructions.
.IMPORTANT - Conservezces
instructions pour votre inspecteur local.
. IMPORTANT - Respectez toutesles
orclonnances et les codes Iocaux.
, Note 6 I'installateur - Assurez-vous de laissez ces
instructions au consommateur.
Note au consommateur - Conservez ces
instructions pour r6f6rence future.
La garantie ne couvre aucune panne clue 6 une
mauvaise installation.
AAVERTISSEMENT -
Cet appareil dolt @trebien mis 6 la terre.
.IMPORTANT -vousdevezv@ifierque
cetappareiln'aitpas de fuiteconform6ment aux
instructions du fabricant.
, L'installateur est responsable d'une bonne
installation et la garantie ne couvre aucune
panne due 6 une mauvaise installation.
A AVERTISSEMENT - D6brancheztout
courant 61ectrique au niveau du disjoncteur de la
maison ou de la boTte 6 fusibles avant d'installer.
POUR VOTRE SECURITI_
AAVERTISSEMENT -
si vous ne suivez pas exactement les instructions
de ce manuel, vous risquez d'occasionner un
incendie, une explosion ou une fuite de gaz, qui
peuvent provoquer des dommages mat@iels, des
blessures corporelles ou la mort.
Ne conservez pas ou n'utilisezjamais d'essence
ou d'autres liquides ou vapeurs inflammables 6
proximit6 de cet appareil ou de tout autre appareil
m6naged
Ne pas installer ce produit si I'on utilise une hotte 6
rideau d'air ou une hotte de cuisini6re soufflant Fair
au-dessus de la surface de cuisson. Le d6bit d'air
peut nuire au fonctionnement des brOleurs 6 gaz et
repr6sente un risque d'incendie ou d'explosion.
CI QUE VOUS DEVEZ FAIRE SI
VOUS SENTEZ LE GAZ •
, N'essayezjamais d'allumer un appareil
61ectrom6nager. Netouchez 6 aucun
commutateur d'61ectricit6, n'utilisezjamais un
t616phoneclans votre batiment.
, Appelez imm6diatement votre fournisseur de
gaz 6 I'aide du t616phone d'un voisin. Suivez les
instructions de votre fournisseur de gaz.
,Si vous ne pouvez pas entrer en contact avec
votre fournisseur de gaz, appelez les pompiers.
L'installation et le service de votre table de cuisson
doivent @trefaits par un installateur qualifi6, un
technicien de service ou votre fournisseur de gaz.
31-i0861 (07-!2 GE) i

Instructions d'installation
INSTRUCTIONS IMPORTANTES DE SI CURITI
LGconception de votre table de cuisson a 6t6
approuv6 par I'ACNOR International. Vous trouverez
des pr6cautions 8 prendre en mati_re de s6curit6
dans votre Guide d'utilisation et de soins. Lisez-les
attentivement.
, L'installation de votre table de cuisson
doit se conformer aux codes Iocaux ou, en
I'absence de codes Iocaux, au National Fuel Gas
Code, ANSI Z223.1/NFPA 54 Derni_re 6dition.
, Assurez-vous que votre table de cuisson soit
bien install6e par un installateur qualifi6 ou un
technicien de service.
, Pour 61iminer tout mouvement corporel au dessus
des br01eurs de votre table de cuisson, 6vitez de
placer des armoires de cuisine au dessus des
br01eurs.
. N'installezjamais votre appareil pros d'une porte
d'entr6e ou dans un emplacement oQ un courant
d'air peut g@ner son usage.
s s
BESOINS D'ELECTRICITE
Cet appareil m6nager doit @tre livr6 avec le bon
voltage et la bonne fr6quence et branch6 6 son
propre circuit de d6rivation bien mis 6 la terre,
prot6g6 par un disjoncteur ou un fusible qui ont
I'amp6rage nots sur la plaque min6ralogique de
votre appareil.
Nous vous recommandons de faire brancher le
c_blage 61ectrique et la fiche de votre cuisini@re
par un 61ectricien qualifi6. Apr@s I'installation,
demandez 6 1'61ectricien de vous montrer
I'emplacement de votre coupe-circuit principal.
Demandez 6 votre entreprise de services publics les
codes 61ectriques en vigueur dans votre r6gion. En
ne c@blant pas votre cuisini6re conform6ment aux
codes en vigueur, vous provoquez une situation
dangereuse. En I'absence de codes, vous devez
c_bler et isoler votre cuisini6re conform@ment aux
exigences du Canadian Electrical Code.
PII_CES COMPRISES
2 vis Bandes de mousse (Pour 2 Supports de fixation
les modules @surface en
verre seulement)
MATE'RIAU× DONT VOUS POUVEZ
AVOIR BESOIN
Raccords de tuyaux
Agent de scellement
de tuyau Robinet d'alimentation
de gaz
Raccord flexible de gaz approuv@ par I'ACNOR
DI min 3/8", Jonction NPT 1/2
OUTILS DONT VOUS AUREZ BESOINS
Crayon
Tournevis Phillips
R@gleordinaire ou de
v@rification
Lunettes de s@curit@
Scie sauteuse
CI66 tuyau
Perceuse 6 main ou _lectrique
et foret de !/8po

Instructions d'lnstallation
LISTE DE VITRIFICATION AVANT INSTALLATION
[]
@
Pour pr6parer I'ouverture de la surface de
cuisson, vous devez vous assurer que
I'int#rieur de I'armoire ne touche pas la table
de cuisson (consultez la section sur la
pr#paration de I'ouverture).
Enlevez les mat6riaux d'emballage, les
bo?tes de grille, le r6gulateur avec sa
documentation et la documentation de
votre table de cuisson avant de commencer
I'installer.
Boites de
grille
_mballage
deJ
Table
CUISSOn
E1 Enlevez les instructions d'installation de la
trousse de documentation et lisez-les
soigneusement avant de commencer.
Assurez-vous de bien ranger toute la
documentation, le manuel d'utilisation et
d'entretien, etc. dans un endroit s0r pour
r#f6rence future.
r6] Assurez-vous d'avoir tousles outils et tous
les mat6raux n6cessaires avant de
commencer _ installer votre table de
cuisson.
r_ votre maison dolt #tre aliment#e en courant
#lectrique ad#quat pour vous permettre de
bien utiliser en toute s#curit# votre table de
cuisson. (Consultez la section sur les besoins
d'#lectricit#.)
r_ Pour installer votre table de cuisson dans
votre maison, assurez-vous de vous
conformer scrupuleusement _ tousles
codes et _ toutes les ordonnances locales.
[] Assurez-vous que les rev@tements
de mur, le comptoir et les armoires autour
de la table de cuisson puissent supporter la
chaleur [pouvant atteindre 93°C (200°F)]
produite par la table de cuisson.

Instructions d'lnstallation
PREPARATION DE L'OUVERTURE
FT] vous DEVEZ RESPECTERLES
DEGAGEMENTS MINIMAUX SUIVANT
Profondeur max de 33 cm (13") des
armoires en surplomb non prot6g6es D6gagement rain. de 15
cm 16")d6coupage au
mur de c6t6 6 droite de
I'appareil
D6gagement min. de 76 cm (30") du
comptoir 6 la surface en non surplomb
non prot6g6es
D6gagement min
de 10 cm (3-3/4") du
d6coupage au mur de
c6t6 droite de ]'appareil
REMARQUE: Laissez un
d6gagement vertical
minimum de 1,1 cm (7/16
po) entre le dessus de la
table de cuisson (ou une
profondeur minimum de
9,2 cm (3-5/8 po) et toute
surface combustible, par
exemple un tiroir d'armoire.
9,2cm !
13-5/8"1T
Hauteur min
de 45 cm (18")
du comptoir
6 ]'armoire la
plus proche de
chaque c6t6 de
I'appareil
i,icm (7/16")
TIROIR f1
Pour une installation en Tlot, maintenir une distance
minimum de 6,3 cm (2 1_ po) entre le bord et le dos
du comptoir et 7,6 cm (3 po) minimum sur les c6t6s
du comptoir.
[_] DIMENSIONS DU DI_COUPAGE DE
LA TABLE DE CUISSON
53 cm (21")(54,6 cm [21-1/2"]
91 cm (36") "_- max. pour table de cuisson en
_I-_"-_ I ! verrel
_Tnhlp Hp r_fi<qnn _'_" 8,1cm (3-3/16")
L.--"__/ _ " pour tabbde
"_ ...... , mv_ 86 cm cuisson ZGU36)
48 cm 18-7/8" "_J/ (33-11/16")
r_ DIMENSIONS TOTALES DE LA
TABLE DE CUISSON
Pour assurer lajustesse du d6coupage,
il vaut mieux faire un gabarit pour couper
I'ouverture dans le comptoir.
86 cm (33-7/8 Largeur du d6coupage
po),longueur du "_ _ 48,5 cm (19-1/8")
aecoupage ___I-_--- --_
cuisson 6,4 cm (2-1/2") Distance min. de
I'ar_te avant du d6coupage de
I'arr_te avant de la table de cuisson
[_ EMPLACEMENT RECOMMANDE DE
L'ALIMENTATION DE GAZ
PARTIR DU MUR ARRIERE
Emplacement
recommand6 de
I'aJimentation
de gaz
2,5 cm (i") min. du mur arri@re
Du
< d6coupage 6
i' la ligne
du centre
r_ ASSUREZ-VOUS OUE LES
REVETEMENTS MUR, LE COMPTOIR
ET LESARMOIRES AUTOUR DE LA
TABLE DE CUISSON PUISSENT
SUPPORTER LA CHALEUR
(POUVANT ATTEI NDRE 93°C [200°F]}
Les rev_tements de
mur, lesarmoires et
le comptoir doivent
pouvoir supporter
une cha]eru pouvant
atteindre 93°C (200°F)
[]_] INSTALLATION POUR PERSONNE
HANDICAPI_E SEULEMENT (E.-U. •
DISABILITIES ACT FORWARD
APPROACH}"
Laissez une
profondeur
minimum de 12,7
cm (5 po) entre la
table de cuisson et
une enceinte.
5"1 li
:=:fl
REMARQUE : L'enceinte dolt _tre H
construite en bois. Aussi, un panneau h
d'acc_s est n6cessaire pour la prise 61ectrique,
le r6gulateur de pression, le robinet de
sectionnement, les supports de retenue et I'entretien
ou les r6parations.