GE DBL333 Operating instructions

GEAppliances.com
Safety Instructions ......... 2-5
Operating Instruotions
Control Panels ................ 6
Control Settings ............... 7
Loading and Using tile DIyer . . .8, 9
Installation Instruc_tions
Electrical Requirements ....... 11
Exhausting the DiTer . ........ 12
Installing the Dwer ........ 1,9,-19
Preparing to Install the DiTer . . 10
Troubleshooting Tips ..... 20, 21
Consumer Support
Consumer Support .... Back Co_er
Warranty ................... 23
DBL 333
DCL 333
DI,Z223
Write the model and serial
numbers here:
Model #
Serial #
You can lind them on the label
on the fl'ont of the leti side of
the door opening.
1342021008 175D1807P436 49-90172-1 08-03 JR

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING!
Foryoursafety,the informationin thismanual must be followed tominimize the risk of fire
or explosion,electric shock, or toprevent propertydamage,personal injury,or death.
•Do notstoreor usegasoline or other
flammable vaporsandliquids in the
vicinityofthis or anyother appliance.
•Installation and service mustbeperformed
by a qualified installer,service agency or
the gas supplier.
WHATTODOIF YOUSMELLGAS:
]Do nottryto light a match, or cigarette, or
turnon anygas or electrical appliance.
[] Do nottouchanyelectrical switch;
not use anyphone in yourbuilding.
[] Clear the room,buildingor area ofall
occupants.
[]Immediately, call yourgassupplierfrom
a neighborsphone.Follow thegas
supplier'sinstructionscarefully.
[] ff youcannot reach yourgassupplier,
call the fire department.
Cafifomia Safe Drinking Water and ToxicEnforcement Act
This act requires tile goxernor of Califimfia to publish a list of substances knox_n to tile state to cattse cancei,
birth detects or other reproduefixe hai_n and requires l)usinesses to warn custolnei_ of potential exposure
to Stlch stlbstances.
Gas appliances can cause minor eN)osure to fl)ur of these substances, namely benzene, carbon monoxide,
timnaldehvde and soot, caused primarily by the incomplete combustion of natural gas or I,P filels.
Properly ac!iusted dxTex_ will minimize incomplete combustion. EN)osure to these substances can be
mininlized flu'ther by l)rol)erly venting tile diver to tile otltdoors.

GEAppliances.com
WARNING!
PROPERINSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions
before it is used.
Proi)erE', ,gr°und dr_er to conforn/with all
goxerning codes and ordinances. Follow
details in the Installation Instructions section.
Install or store where it will not be exposed
to temperatures below freezing or exposed
to the weather.
Connect to a properl) rated, protected and
sized power supply circuit to a_oid electrical
o_erload.
Remove all sharI_ I)ackin'",. items and dispose
of all shii)ping materials i)roperly,
Exhaust/Ducting:
_] This dryer MUSTbe exhausted to the outside.
[]Use onl)rigid metal 4" diameter ductwork
inside the dr_er cabinet. Use only rigid inetal
or flexible inetal 4" dialneter ductwork tor
exhausting to the outside. USE OFPLASTICOR
OTHERCOMBUSTIBLEDUCTWORKCANCAUSE
A FIRE.PUNCTUREDDUCTWORKCANCAUSEA
FIREIF IT COLLAPSESORBECOMESOTHERWISE
RESTRICTEDIN USEORDURINGINSTALLATION.
Follow details in the Installation Instructions section,
YOURLAUNDRYAREA
•Kee I) the area underneath and around wmr
appliances fl'ee of combustible materials, such
as lint, paper, rags, chemicals, gasoline and
other flammable vapors and liquids.
•Kee I) the floor around your appliances clean
and dry to reduce the possibili Wof slipping.
•Kee I) area around the exhaust opening and
smTounding areas free fl'om the accumulation
of lint, dust and dirt.
Do not obstHict the flow of _entilating air.
Do not stack or place latmdrv, or throw _ugs
against the front or back of the dryer.
•Close supervision is necessa_ y if this appliance
is used bv or near children. Do not allow
children to play on, with or inside this or
any other appliance.
•Kee I) all laundry aids (such as detergents,
bleaches, etc.) out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid iqjury.
•Never climb on or stand on the dryer top.
•Do not install or store this appliance where
it will be exposed to the weather.
3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
4
.4,WARNING!
WHENUSINGYOURDRYER
• Never reach into the dryer while the chum is
moving. Before loading, unloading or adding
clothes, wait until the dram has completely
stopped.
•Clean the lint filter before each load to prevent
lint accumulation inside the dryer or in the
room. DO NOT OPERATETHE DRYER WITHOUT
THE LINT FILTERIN PLACE, UNLESS THE DRYING
RACK IS IN USE.
•Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers,
dry-cleaning solvents, kerosene, etc.). These
substances give offwq)ors that may ignite or
explode. Do not add these substances to the
wash water. Do not use or place these
substances around your washer or dryer during
ol)eration.
•Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beg uty sahms, testa urants or barber shops,
etc.) must not be placed in or near the dryer
tmtil solvents or flammable materials have
been removed. There are many highly
flammable items used in homes such as
acetone, denatured alcohol, gasoline, kerosene,
soI//e household cleaners, SOllle spot relllovers,
turpentines, waxes, wax removers and products
containing petroleum distillates.
•The latmd_ T process can reduce the flame
retardancy of fabrics. To avoid such a result,
careflfllv follow the garment illantll;ictttYei"s
caI'e insti fictions.
•Do not d_y articles containing robber, plastic,
or similar materials such as padded bras, tennis
shoes, galoshes, bath mats, rugs, bibs, baby
pants, plastic bags, pillows, etc. that may melt
or burn. Some _ubber materials, when heated,
can under certain circumstances produce fire
bv Sl)ontaneotls COll/btlstion.
•Do not store plastic, paper or clothing that
may bm'n or melt on top of the dryer dm'ing
ol) eration.
•(;am/ents labeled Dry Away from Heat or Do Not
Tumble Dry (such as life jackets containing
Kapok) IlltlSt not be put in your dryer.
•Do not dry fiberglass articles in wmr dryer.
Skin irritation could result fl'om the remaining
particles that may be picked up by clothing
dtlring stlbseqtlent diwer rises.
•To minimize the possibility of electric shock,
tmI)lug this appliance fl'om the power sui)ply
or disconnect the dryer at the household
distribution panel by removing the fltse or
switching off the circuit breaker befin'e
attempting any maintenance or cleaning
(except the removal and cleaning of the lint
filter). NOTE: Turning the Cycle Selector knob
to an off position, or pressing PAUSEdoes NOT
disconnect the appliance from the power supply.
•Do not spray any type of aerosol into, on or
Ile}lY dryer at }lily time.
•Do not place items exposed to cooking oils in
wmr dryer. Items contaminated with cooking
oils may contribute to a chemical reaction that
could cause a load to catch fire.
•Never attempt to operate this appliance
if it is damaged, malflmctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
•The interior of the machine and the exhaust
duct connection inside the dryer should be
cleaned at least once a year by a qualified
technician. See the Loading and Using the Dryer
section. Do not use any type of spray cleaner
when cleaning (hTer interior. Hazardous tirades
or electrical shock could occm:
•If wmrs is a gas dryer; it is equiI)I)ed with an
automatic electric ignition and does not have
apilot light. DO NOTATTEMPT TO LIGHT WITH
A MATCH. Burns may result from having your
hand in the vicinity of the burner when the
automatic ignition turns on.
• You mav wish to soften wmr latmdered fabrics
or reduce the static electricity in them by using
a drye>applied fabric softener or an anti-static
conditioner. X_'erecommend you use either a
tabric softener in the wash cycle, according to
the manufacturer's inst_ uctions fin" those
products, or try a (hTe>added product fin"
which the manufi_cturer gives written assurance
on the package that their product can be safely
used in wmr dryer. Se_Mce or l)ertormance
problems caused by use of these products are
the responsibility of the mamdhcmrers of
those products and are not covered trader
the warranty to this appliance.

GEAppliances.com
WHENNOTUSINGYOURDRYER
• Grasp tile plug firmly when disconnecting this
appliance to avoid damage to tile cord while
pulling. Place tile cord away from traffic areas
so it will not be stepped on, tripped over or
subjected to damage.
• Do not attempt to repair or replace any part
of this appliance or attempt any servicing
unless specifically recommended in this
Owner's Manual or in i)ublished use_rei)air
instructions that w)u understand and have
the skills to carry out.
• gefln'e discarding a d_ye_; or removing it
fYOIIl service, i'elllOVe tile dryer door to
prevent children from hiding inside.
• Do not tamper with controls.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS

Aboutthe controlpanel
Youcan locate your model number on the label on the front of the left side of the door opening.
Model DBL333
START TEMPERATURE
START MEDIUM
I_ ire
LESS DRY MORE DRY
20 30 40 50
ir.j
LESSDRY
80 MIN
TIMED DRY
60
Model DCL333
START
START
LESS DRY
OPTIMUM DRY
COTTONS
AUTOMATIC
REGULAR HEAT
MORE DRY
MORE DRY
LESS DRY
COOL
DOWNEASY CARE
AUTOMATIC
MEDIUM HEAT
el lo 2030®
ir.j
FLUFF
NO HEAT
50
Model DVL223
START
START
80MIN
LESS DRY
OPTIMUMDRY
el 20
ir.j

Aboutthe controlsettings.
NOTE:Not aft features are available on all dryer models. GEAppliances.com
IMPORTANT'.Clean the lint filter each time you use the dryer.
_r_ Temperature
REGULAR Forregularto heavycottons.
MEDIUM Forsynthetics,blends,delicatesanditemslabeledpermanentpress.
FLUFF Forfluffingitemswithoutheat.UsetheTIMEDDRYcycle.
NOHEAT
_ tltomafic cycles atmnnaticalh detemfine lid)tic dryness. Select LESSDRYif_ou want your clothes slightly damp
at the end of the (hTing cycle. Select MORE DRY if you want them to feel drie_:
Drying Cycles
COTTONS Forcottonsandmostlinens.FormostloadsselectOPTIMUMDRY.
EASYCARE Forwrinkle-free,permanentpressanddelicateitems,andknits.
TIMEDDRY SettheCycleSelectoratthedesireddryingtime.
FLUFF Providesno-heattumblingforfresheningorfluffingalreadydryclothing,fabric,linensandpillows.
_J Sta_(_lose the dryer doon Turn the STARTcontrol clockwise to START.Hold fl_r 1-2 seconds and release.
Oi)ening_ the door dm_ing, oi)erafion will stop the (h'_ e_: To restnrt the (h'_ e_; close the door and
select STARTto complete the cx cle.
NOTE:Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of
load, types of fabrics, wetness of clothes and condition of exhaust ducts.

Loadingand usingthedryer.A/woysfollowthef_bricmanufacturer'scare/abel when/aundering.
SortingandLoadingHints
_&s a general Hlle, if clothes are sorted properl)
for tile washer, thex are sorted properly for
the (h'_ er.
Do not add fabric softener sheets once the load has
become warm. Theymay cause fabric softener stains.
Bounce®Fabric Conditioner Dryer Sheets have been
approved for use in all GEDryers when used in
accordance with the manufacturer's instructions.
Do notoverload.This wastes energy and causes
wrinkling.
Do notdrythe following items: fiberglass items,
woolens, rubber-coated items, plastics, items with
plastic trim and foam-filled items.
CareandCleaningof theDryer
The Exterior:_,_ipe or dust an_ spills or washing
compounds with a damp cloth. Dr) er control
panel and finishes may be damaoed_ b'_, solne
laundr) pretreatment soil and stain remoxer
products. Apply these products away from tile
dryer. Tile tabric may then be washed and dried
normally. Damaoe to _our (hwer caused by these
products is not coxered b) your warrant_.
TheExhaustDuct:Inspect and clean tile exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen tile
drying tim e.
Follow these steps:
_Turn oft electrical su ) )l_ 1)_ disconnecting
tile )luo- from tile wall socket.
The Lint Kilter: Clean tile lint filter before each
use. Remove by pulling straight up. Run your
finge_ across the filtec A wax) buildup ma) fi)rm
on the lint filter fi'om using dr) e_=adcted f_bric
softener sheets, To remove this buildup, wash tile
lint screen in warm, soapy water. Dry thoroughly
and replace. Do not operate tile dryer without
tile lint filter in place.
_ Disconnect tile duct from tile dryer.
_] Vacuum the duct with the hose attachment
and reconnect tile duct.
TheExhaustHood:Check fl'om the outside that
the flaps of the hood move fl'eely when operating.
Make sure that there is no wildlife (birds, insects,
etc.) nesting inside the duct or hood.
Have a qualified technician vacuum tile lint
[i'()Ill tile dr_,er once a veal'.

GEAppliances.com
FabricCareLabels
WASH LABELS
Machine ___
wash
cycle Normal U
Permanent Press/
wrinkle resistant Gentle/ Do not wash Do not wring
delicate Hand wash
Water
temperature 000 O0 •
Hot Warm Cold/cool
(50°C/120°F) (40°C/105'_F) (30°C/85'_F)
BLEACHLABELS
Bleach A
symbols Any bleach
(when needed) Only non-chlorine bleach Do not bleach (when needed)
DRY LABELS
Tumble
dry Dry qDD
Normal Permanent Press/ Gentle/
wrinkle resistant delicate Do not tumble dry Do not dry
(used with
do not wash)
Heat _GQO
setting High Medium Low No heat/air
Special
instructions m Pq
Line dry/ Drip dry Dry flat In the shade
hang to dry

Preparingtoinstall yourdryer.
Read these instructions completely and carefully.
WARNING
• This dryer must be exhausted to the outdoors.
Use only rigid metal or flexible metal 4"
(liameter ductwork for exhausting to the
outside. ILrse only rigid metal 4" diameter
ductwork inside the dryer cabinet.
• Tile National Fuel Gas code restricts installations
of gas appliances in garages. They m ust be l S"
(45.7 cm) off tile groined and protected ti'om
vehicles by a barrier. See Location of Your Dryer
section.
•Never use plastic or other combustible ductwork. •
See Exhausting section.
• This appliance must be properly grotmded
and installed as described in these Installation
Instructions. •
• Do not install or store appliance in an area
where it will be exposed to water/weather.
See location of Your l)ryer section.
The electrical service to the dryer inust
confrere with local codes and ordinances and
the latest edition of the National Electrical
Code, ANSI/NFPA 70.
The gas service to the dryer IlltlSt conIoI'Ill with
local codes and ordinances or the latest edition
of the National Fuel Gas Code ANSI Z223.1.
The gas dryer is designed trader ANSI Z 21.5.1
fin" home use only. This dryer is not
recommended fin" commercial applications
Stlch as i'estatli'ants oi" beatl[V salons_ etc.
ToolsandMaterialsRequiredfor DryerInstallation
[] Phillips head screwdriver
[] A(!justable pliers
[] Carpenter's level
[] Flat or straight blade screwdriver
[] Duct tape
• " 10 2 cm) duct[] Rigid or flexfl)le metal 4 ( .
[] Vent hood
[] Pipe thread sealer (GAS DRYER)
10
PreparingtheInstallationSiteandUnpackingtheDryer
_] Prepare the area and exhaust for installation A
of the new drxer.
[_ Check to be sm'e that the existing external
exhaust is clean and that it meets attached
installation specifications. []
_] Using the fotlr shipl)ing carton corner posts
as padding (two on each side), careflfllv lax []
the dryer on its left side and remoxe foam
shii)ping pad. []
[]
Foamshippingpad
Packing
CAUTION2 To )rexent damage,
l
do not rise the control panel as a ii/e_lns
to pick up or mo_e the dr_er.
Return the dr_er to an upright position.
JVloxe the dryer to the desired location.
Connect the external exhaust.
Ad ust the lexelin,* leo-s to match the washer
height. The dryer i//tlSt be lexel and rest
firmE on all fotlr lexeling legs.
Connect the power SUl)ply.
[]
[_ Check the operation of the power suppl)
and xenting.
Place the Owner s Manual and the
Installation Instructions in a location where
they will be noticed 1)_the owner.

Electrical requirements.
Read these instructions completely and carefully.
ElectricalConnectionInformationforElectricDryers
I,'I/A _IIII All _
Vllf/-Irl/ll/l/l/[./-- To reduce the risk
of fire, electric shock or personal ii_j ury:
°DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
•THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Electrical Requirements
•This dryer must be connected to a 208V or
240V individual branch circuit, protected by
30 amp circuit breakers or time-delay fllses.
•Use copper condtlctors onlvi
Thisdryermustbe electricallygroundedin
accordancewith local codesand ordinances,or in
theabsence oflocal codes,in accordancewith the
NATIONALELECTRICALCODE,ANSI/NFPANO.70.
•If the electric supply does not meet the above
specifications, call a licensed electrician,
NOTE:A wiring diagram is located inside the
control panel.
ElectricalConnectionInformationforGasDryers
WARNING- To,.ed,..e ,.i.¢
ot fire, electric shock or personal ii_jmT:
•DO NOT USEAN EXTENSION CORD OR AN
ADAPTER PLUG WITH THIS APPLIANCE.
•DO NOT UNDER ANY CIRCUMSTANCES, CUTOR
REMOVE THE THIRD GROUNDING PRONG FROM
THE POWER CORD.
This dryer must be electrically grounded in
accordance with local codes and ordinances, or in
the absence of local codes, in accordance with the
NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70.
Electrical Requirements
•This dryer must be supplied with 120V, 60 Hz,
and c(mnected to an individual properly
grotmded branch circuit, protected bv a 15 or
21) amp circuit breaker or time-delay fuse.
• If the electric supply provided does not
meet the above specifications, it is
recommended that a licensed electrician
ExternalGround(if required)
An external groundwire (notprovided), which
meetslocal codes,may be addedbyattachingit to
thegreengroundscrew on theroarofthedryerin
theupperleft cornerabovethecord,and togrounded
metal coldwater pipe or otherestablished ground.
I'_ Attachgroundwire
|(obtainlocally/
:U
o
NOTE:A wiring diagram is located inside the
control panel.
install an approved outlet.
11

Exhaustingthe dryer.
Read these instructions completely and carefully.
ExhaustSystemRequirements
Use only 4" (102 cm) diameter (minimum) rigid metal
duct for best performance, or flexible metal duct. Use
approved vent hood which has swing-out dampe_
that open when the (hTer is in operation. When the
dryer stops, the dampers automatically close to
prevent drafts and the entrance of insects and
rodents. To avoid restricting the outlet, maintain a
minimum of 12" (30.5 cm) clearance between the
vent hood and the grotmd or any other obstruction.
If all rigid metal duct cmmot be used, then flexible
all-metal venting can be used, but it will reduce the
maximmn recommended duct length. See Additional
Installation Instructions folloMng
Correct
Incorrect
Don't
Don't
Don't _
WARNING:thefollowingare specific
requirementsforproper andsafeoperationofyour
dryer Failuretofollow theseinstructionscancreate
excessivedryingtimesandfire hazards.
DO NOT use plastic flexible duct to exhaust the
dryer. Excessive lint can build up inside exhaust
systemand create a fire hazard and restrict air
flow. Restricted air flow will increase dryingtimes.
If yourpresent systemis made up ofplastic duct
or metal foil duct,replaceit with rigidor flexible
metal duct, Ensure the present duct is free of any
lint prior toinstallingdryerduct.
A
A
A
The dryer exhaust systemMUST BE EXHAUSTED
TO THE OUTSIDEofthe dwelling.
DO NOTallo_ combustible materials (fbr example:
cloflfing, (h'ai)eries/curtahls, t)aper) to come in
contnct with exhaust system.
ThedryerMUST NOT be exhausted intoa gas vent,
chimney,a wall, a ceiling, a commonduct with a
kitchen exhaustor any concealed space of a
building which can accumulate lint,resulting in
a firehazard.
DO NOTexceed the length of duct pipe or
ntlIIlbeI" of elbow, s allotted in the MaximumLength
charts. Lint can acctli/lt/late in the exhaust
system, plugging the system and creating a fire
hazm'd, as well as increasing drying dines.
DO NOTscreen the exhaust ends of the vent
s vsteill, noi" rise [lIIV scYews ()r I_;'ets to assemble
the exhaust system, iJnt can become caught in
the screen, on the screws or rivets, clogging the
duct work and creating a fire hazard as well as
increasing (h?.'ing times. Use an approved vent
hood to temfinate the duct outclooI_, and seal
all joints with duct tape. M1 male duct pipe
fittings MUSTbe installed downstream with
the flow of ai_;
EXPLOSION HAZARD.Do not install the dryer
where gasoline or other flammables are kept
or stored. If the d_'er is installed in a garage,
it must be a minimum of 18" (45.7 cm) above
the flora: Failure to do so can result in death,
explosion, fire or bm'ns.
_ rovide an access tot inspection and cleaning of
the exhaust s)stem, especiall) at turns, Inspect
and clean at least once per yea_:
Do not obstruct incoming or exhausted ai_:
12
Additional Installation Instructions
If all rigid metal duct cannot be use& then flexfl)le
all-metal venting can be used, but it will reduce the
maxim mn recommended duct length. In special
installations when it is impossible to make a
connection with the al)ove recommendations, then
UL-listedclothesdryertransitionduct may be used as
transition venting between the dryer and wall
connection only. The use of this ducting will affect
(hTing time.
If flexible transition duct is necessary, only UL-listed duct
identified for use with clothes dryersisapproved,
The following directions must be followed,
• Use the shortest length possible.
• Stretch the duct to its maximmn length.
•Do not CI'ush 0I" collapse.
• Never use transition duct inside the wall, flooring,
ceiling or inside the dryer
• Avoid resting the duct on shaq) objects.
• Venting must confl)m_ to local building codes.

Installingthedryer.
Exhaust Ducting Length
Tim exhaust s}stem should be inspected and cleaned
at least once a year with nomml usage. Tim more tim
dryer is used, tim more often you should check tim
exhaust system and vent hood fin" proper openJfion.
If roof vents or louvered plenums are used, they must
be equivalent to a 4" dampered wall cap in regard to
resistance to aiHhtx% prevention of back drafts and
maintenance required to prevent clogging.
°DONOTassemble tile duct work with ti_stenex_ that
extend into the duct. Thev will serve as collection
points fin" lint.
•Ductwork wlfich runs fl_rough an tmheated area or
is near an air ctmditioning duct should be insulated
to reduce ctmdensation and lint build-ui).
MAXIMUM LENGTHof4"(10.2cm)Din.RIGIDMETALDUCT
PREFERREDVENTHOODTYPE
4" (10.2 cm)
Number of
90°1_.... _ 1{102c")l _K"
0 60"
1 52"
2 44'
3
4
Louvered
116.28,.)
{15.84m)
(13.41m)
48"{14.63m)
40' {12.19m)
32" (9.75m)
MAXIMUM LENGTHof4"(10.2cm)Dia.FLEXIBLEMETALDUCT
PREFERREDVENTHOOD TYPE
Number of
90° turns
4"(10.2 cm) Louvered
- 11,0;4-
30"{9.14m)
22" (6,71m)
14"(4,27m)
0
1
2
18" (5.49 m)
14" (4.27 m)
10' (3,05 m)
32" (9.75m)
28" (8.53m) 24" (7.31 m) 3 16" (4,87 m)
INSTALLMALE FITTINGSIN
CORRECTDIRECTION
notrecommended
ExhaustDirection
M1 drve_ are shil)ped set up tor rear exhausting.
On electric dtTet_ ,exhausting can be on the cabinet
right or left side, or through the dtTer bottom.
Gas dt_'et_ can exhaust on the cabinet right side or
tim (hTer bt)ttom. To change exhaust direction you
will need Exhaust Ydt, Pub. No. 14-A018 and a rigid
metal 4" 90 degree elbow. The kit is a\:filable through
vom" GE retaile_: Follow tile instructions supplied
with tile kit.
L
,/Same as EXHAUSTDUCTLOCATING
|Pottlerside DIMENSIONS
,4._," ,5-7/8"
(15cm) 4-3/8"
cm}
3-3/4"(9.5cm} {9.5cm)
GasSupplyRequirements
AReplace brass com_ecfing pipe that is not
plastic-ctn_ted. Stainless steel or plastic-coated
brass MUSTbe used.
[]
WARNING:Ne.,e,-,e.se,,klt> ,.le
coimectors. The use of oM flexible commctors can
cau_ gas leaks a_M l)ers°nal ini.urx. Mx_avs•use NEW
fleMble connectors _d_en installing a gas appliance.
Installation MUSTconfi)rm with h)cal codes, or
in tile absence of htcal codes, with tile National
Fuel Gas Code, ANSI Z223.1 (latest edition).
[]
[]
[]
[_The gas suppl_ line should be of 1/2" (1.27 cm)
rigid pipe. []
_]]f codes allow, fleMble metal tubing may be used
to ctmnect your dryer to tile gas supplx line. Tile
tubing MUSTbe constructed of stainless steel or
plastic-coated brass.
Tile gas suppl)line MUSThaxe an individual
sh tlt()tt xalx e.
A 1/8" (0.32 cm) NPT minimum l)lugged,,
tapping, accessible fl)r test moauge,c(mnection,
MUSTbe installed immediately upstream ot the
gas supply cmmection to tile dryer:
Tim (hTer and its individual slmtoffxahe MUST
be disconnected from tile gas suppl_ ll)i)ira,
s\:stem during any pressm'e testing of tile gas
supply piping system at test pressm'es in excess
of 1/2 psig (3.45 kPa).
Tile (hTer MUSTbe isolated from tile gas supl)ly
ll)i)ira,,. system. 1)_,ch)sing, its individual manual
shutt)fl \_flve during any pressm'e testing Jff tile
gas supply piping system at test pressm'es
equal to or less than 1/2 psig (3.45 kPa). 13

Installingthedryer.
Read these instructions completely and carefully.
Locationof YourDryer
Do Not Install the Dryer:
_] Donotinstall thedryerin an area exposed to
dfiI)I)ing water or outside weather conditions.
]Do not install the dryerin an area where it will
come in contact with curtains, drapes or
an)thing that will obstruct tile flow of
combustion and xenfilafion ai_:
]Do not instaflthe dryeron cmpet.
Floor MUSTbe solid with a maximum slope
_5
ot 1" (2.: 4 cm).
Installation in Recess or Closet
[]This dryer MUST be exhausted outdoors.
]No other fuel bm'ning appliance shall be
installed in tile same '(]()set as tile GASDRYER.
[_] Y)ur dryer needs tile space aro/md it fi)r proper
xentilatfon. DONOT INSTALL YOURDRYERIN
A CLOSETWITH A SOLID DOOR.
[_ Closet do(n5 must be louxered or otherwise
xenfilated and must contain a minimum of
60 sq. in. of open area equally distributed.
If the closet contains both a washer and a d_Te_;
dool_ II/USt contain a minim mn of 120 sq. in. ol
open area equally distributed. _dr openings are
required to be tmobstructed when a door is
installed. A louvered door with equivalent air
openings for tile flfll length of tile door is
acceptable.
0
I
Closet door
60sq.in.
(387.1sq.cm)
i €._ 0"(0cm)
AIIowthe followingclearancesfor easeofbstallation:
FRONT SIDES REAR* TOP
1"(2.54cm) 0(0cm) 1"(2.54cm) 15"(38.1cm)
*Additionalrear clearancemaybe requireddepending
ontheductinginstallation,
T
15"
(38.1cm) 1"(2.54cm)
/4

Mobile Home Installation
_] Lh) er MUSTbe exhausted outside (out(loo_, not
beneath tile mobile home) using metal ducting
that will not support combustion. Metal ducting
must be 4" (] 0.] 6 cm) in diameter with no
obstructions. Rigid metal duct is preferred.
_]f dryer is exhausted through tile floo_; tile
exhaust s_stem MOST NOT temfinate beneath tile
mobile home. Temfinafion MUSTbe securely
ti_stened to tile mobile home structure.
_] X._q/en installing a dx) er into a mobile home,
a provision IlltlSt be made for outside make-up
ai_: Provide an opening with a ti'ee area of at
least 25 square inches fin" introduction of outside
air into tile (lI'veI" i'OOill.
[_ (;as dryex_ MUSTbe fi_stened to tile floor
using Mobile Home Installation ICdt
Pub. No. 14-DB4&Sb.
_]See tile Exhaust System Requirements section
fin" other important xenting infimnation.
@Installation MUSTconf(mn to current
Manttfilctured Home (_onstrucfion g,"Sale D'
Standard (which is a Federal Regulation Title
24 CFR--Part 32-80) o_; when such standard is
not applicable, with Mnerican National Standard
fin" Mobile Homes, ANSI/NFPA No. 501 B.
Correct
Incorrect
Don't
Thedryeris designedunderANSIZ21.5.1
for HOMEUSEonlg
flough-lnDimensions
267/8"
-- (68.3cm)
Electricalconnection
29/16'_,.
(6.5cm)
131/2"
(34.4cm)/
! o t
.8_:
-f_ 3/8" 10.96cm)Dia.
33/4" gaspipe 1" (2.54cm)
(9.5cm)
435/8"
(110.7cm)
R_RVIEW
1
36"
(91.5cm)
!
Dooropen
90°
471/2"
_m
43/8"._
(11.1cm) ] _-"
Optional-----,L.""1
ventknockout .
27" _ f
(68.6cm) 33/4"
(9.5cm)
SIDEVIEW
Servicing -Considerationmustbe given toprovide adequate clearances for installation and servicing.
15

Installingthedryer.
Read these instructions completely and carefully.
GroundingRequirements
ADANGER:,mp..pe._o..e_io.o,_he
equipn_ent-grounding conductor can result in
a risk of electric shock. Check with a licensed
electrician if you are in doubt as to whether
the appliance is propedy grotmded.
Grotmding must be in accordance with local
codes and ordinances, or in the absence of
local codes, in accordance with the National
Electrical Code ANSI/NFPA No. 70.
Fora grounded, cord-connected electric dryer'.
_]The dr*,er MUSTbe .,rounded, In the merit of
a malflmction or breakdown, grom_ding will
reduce the risk of electrical shock by creating
a path of least resistance fin" electrical current.
_]f )am" (h) er is equipped with a power suppl)
cord haxing an e(] [tli)ment-grom_dim*, _ con(hlctor
and a grotmding plug, the plug MUSTbe
plugged into an appropriate, copper-wired
receptacle that is propedy installed and
grotmded in accordance with all local codes and
ordinances. If in doubg call a licensed electrician.
For apermanently-connected electric dryer:
• The dryer MUSTbe com_ected to a grams(led
metal, pemmnent wi_ing system; or an equipment-
grotmding conductor must be run with the circuit
conduct(n_ and cmmected to the equipment-
grotmding temfinal or lead on the appliance.
For a cord-connected gas dryer'.
• This dryer is equipped with a three-prong
(gr(mnding) plug fin" yore" protection against
shock lra/;u'd and should be plugged directly into
a propedy grcmnded three-prong receptacle.
Do not cut or remove the grotto(ling prong ti'om
this plug.
E/ectricalInstallationforE/ectricDryers
_, WARNING:The following are specific ,_ WARNING:AUI,-approved strain
requirements fin" proper and sale electrical
installation of yam" (hTer. Failm'e to fi)ll()w
these instructions can create electrical shock
and/or a fire hazard.
WARNING:This appliance MUSTbe
properly grotmded. Electrical shock can result
if the dryer is not propedy grotmded. Follow
the instructions in this manual for proper
grotmding.
WARNING:ooNOT._ea,,extension
cord with this dryer Some extension cords are
not designed to withstand the alnoui,ts of
electrical cmTent this dryer utilizes and can
melt, creating electrical shock and/or fire
ha/nrd, i,ocate the dryer within reach of the
wall outlet, raking into accotmt the length
of power cord to be pro'chased and allowing
some slack in the cord. Refer to Electrical
Requirements in this manual fi)r the proper
power cord to be pro'chased.
relict must be installed onto power cord. If the
strain relief is not attached, the cord can be pulled
()tit of the dryer and can be Ctlt bv }IIIVn/ovelnent of
the cord, resulting in electrical shock.
AWARNING:Usecopperrecep,.c,e_o.,_.
NOTE:Dryexs operating on 208-volt p()wer supply will
have longer (hTing times than those operating on
240-volt power supply.
A wiring (liagTam is located inside the control panel.
16

3-Wire System for Electric Dryers--DO NOT use for Mobile Home Installations
_ ]_emove the screws securing the temfinal block
access cover and the strain relief mounting
bracket located on the back ot the dryer
tlppeI" Coi'nei;
[_ Install a Ul,-approxed strain relief into the power
cord entr) hole of the mounting bracket. Lrse
a strain relief which attaches to the mounting
bracket with a nut. Finger-tighten the nut only
at this time.
_] Thread a Ui,-approved 30A, 240V, 3 #10 AX4G
Illinil//tllll copper condtlctor po_*,er cord through
the strain relief.
Greenground screw Silverterminal
[_ Attach the power cord neutral (center wire)
conductor to the silxe>colored center temfinal
on the temfinal block. Tighten the screw
securely.
_] Attach the remaining two power cord outer
condtlctors to the ()liter brass-colored tei]ninals
on the temfinal block. Tighten both screws
securely.
WARNING: makea sharp
bend or cfimI _ wiring/conductor, at
connections.
@ Reattach the strain relief mounting bracket to
the back of the d_'er with two screws. Tighten
sc I'eWS securelx.
Greenneutral
groundwire Nut Tighten nut to
[_ Tighten the tiasteners securing the cord restraint
fimfl) against the power cord.
_ Tighten the strain relief nut securel) so that the
strain relief does not turn,
_ Reinstall the temfinal block access coxei:
Use copper Strainrelief
conductorsonly. mountingbracket
Po"_wercord
4-Wire System for Electric Dryers--MUST be used for Mobile Home Installations
_] Remove the screws securing the teHninal block
access coxer and the strain relief mounting
bracket located on the back of the dryer
[_ Attach the red and black power cord conductors
to the outer brass-<'olored teHninals on the
temfinal block,
upper cornei:
[_ Install a UI,-approxed strain relief in the enti T
hole of the mounting, bracket .....Use a strain relief
which attaches to the mounting bracket with a
nut. Finge>tighten the nut only at this time.
_] Remoxe the green neutral ground wire fl'om
the green ground screw located aboxe the
terminal block.
Typical4 _ Black240V
conductor|| | ]4conductorcord_
receptacle_ Typical _¢t. Whiteneutral
ir _ Red240V
"Greenground
[_ Thread a UI,-approved 30A, 240V, 4 #10 AWG
IlliniI/ltlIll copper condtlc[oi" power cord throtlgh
the strain relief.
_ Attach the green power cord ground wire to the
cabinet with the green ground screw.
_] Attach the white (neutral) power cord
con(hlctor fl'Olll the power cord and the green
ground wire ti'om the (h_'er harness to the sihe>
colored center temfinal on the terminal block.
Tighten the screw securelx.
Greenpowercordgroundwire
Greenground _ /
screw _J_,'_'_/__=__/Silver terleinal
k__ _---Terminal ,)10ck
Greenneutral _ _/
.Tl0ht0nnutte
•d/I Strain"_,_ X._". /
.'_/:// relief"'_/4_
Powercord" leounting?)_'_
bracket
,& WARNING:D.,,,,t make a shaq)
bend or crJmi ) wiring/conductor, at the
connections.
_ Tighten the fi_steners securing the cord
restraint firml) against the power cord,
[_ Tighten the strain relief nut securely so the
strain relief does not turn,
N Reinstall the temfinal block access coxer
17

Installingthedryer.
Read these
13instructions completely and carefully.
GasConnectionfor GasDryers
[_] Remove the shii_ping ca ) fl'om o-as pipe at the
rear of the dryer;
NOTE: DO NOTconnect the dryer to 12 gas service
without converting the gas \_i\'e. An I,P conve_ion
kit (Pub, No, 14-A038) MUSTbe installed by
a qualified gas technician.
_ ()mnect a ]/2" ( ] .27 cm) I.D. semi-rigid
or approved pipe from gas sui)plv line to
the 3/8" (0.96 cm) pipe located on the back
of the (hTet: Use a l/9" to 3/8" (1.27 cm to
0.96 cm) reducer fin" a com}ection. Apply an
approved thread sealer that is resistant to the
corrosive action (ff liquefied gases on all pipe
connections.
_] Open the shutoff valve in the gas supply line.
Test all cmmections by, brushing, on a soai _,
[_ water solution.
AWARNING:NEVERTESTFOR
GASLEAKSWITHAN OPENFLAME.
NOTE:On gas (hTe_, befin'e the bm'ner will light,
it is necessm T fin" the gas line to be bled of ai_:
If the burner does not light within 45 seconds the
fi_t time the d_Ter is turned on, the safi_t)'switch will
shut the bm'ner ofl_ If this happens, tm'n the timer
to OFFand wait 5 minutes befin'e making another
attempt to light.
In the Commonwealth of Massachusetts
• This Product must be installed by a licensed
plmnber or gas fitter.
• When using ball-type gas shut-off wflves, they
shall be the T-handle-type.
• A flexible gas connector, when used, must not
exceed 3 feet.
BeforeOperatingtheDryer
_] (:onnect the exhaust duct to outside exhaust
S S _S O S O S
,;y,;tem. L,;e duct tape t ,_eal allj int,;.
Mth the dryer in its final position, a_!just one or
more of the legs tmtil the dr) er is resting solidl)
on all fimr legs. Place a lexel on top of the dr} e_;
THEDRYERMUSTBELEVELANDRESTING
SOLIDLYONALLFOURLEGS.
_Plug the )ower cord into a grounded outlet
NOTE: Check to ensm'e the power is off at circuit
breaker/fllse box befin'e I)lugging,, , the power
cord into the outlet.
_Tm'n on the power at the circuit breaker/
fllse box.
ACAUTION: Before o ,erating the drveI;
I , ,
make sure the (hwer area is clear and fl'ee
fl'om combustible materials, gasoline and
other flammable vapms. _Mso see that nothing
(such as boxes, clothing, etc.) obstructs the
I']OW OI _ coI//b/Istion and ventilation ai_:
@Rtm the dryer through a cycle check fin" proper
oi)ei'ation,
_]If xour (hwer does not operate, please review the
Troubleshooting Tips secdon in this manual befi)re
calling fin" serxice.
[_ Place these instructions in a location near the
dr_er fin" flmu'e reli_rence.
18

ReplacementParts
If replacement parts are needed tot your (hwe_; visit
GEAppliances.com, or call GEParts and Accessories
at 800.626.2002 or contact an authorized parts
supplie_:
,_ WARNING: Destroy tile carton and
plastic bags after tile dryer is tmpacked.
Children might use them fin" play. (_u'tons
covered with rugs, bedspreads or plastic sheets
can become airtight chambe_ causing
suffocation. Place all materials in a garbage
container or make materials inaccessible
to children.
WARNING:Tile instructions in tile
manual and all other literature included with
this dryer are not meant to cover eve_T possible
condition and situation that may occm: Good
safe practice and caution MUSTbe applied
when installing, operating and maintaining
any appliance.
ReversbgtheDryerDoorSwing
[Z] Open tile (h'yer dora: Remoxe tile 4 hinge hole
plugs or screws from tile left side of door
opening. Place neafl)v fl)r flmu'e installation.
NOTEJYoumay need a plastic knife to help ptfll
out tile plugs. Be careflfl not to scratch tile paint.
_ Remoxe tile IOta" screws that secm'e tile door
hinges to tile dryer fl'ont panel. NOTE."Remoxe
1 screw fl'om each of the 9 hinges fi_t. Hokl tile
door fimflv befiwe removing tile last 2 scrmvs.
_] Rotate tile door 180 ° and reinst;fll tile door
hinges to tile (hTer ti'ont panel with tile 4 screws.
[_ Install the 4 hinge hole )lugs or screws that were
remoxed in step 1 into tile open screw holes on
tile right side ot tile door opening.
Remove4screws onefromeachhingefirst
19

Beforeyoucall forservice...
Troubleshooting -tips
Save time and money! Review the charts on the following pages,
or visit 6EAppliances.com. Youmay not need to call for service.
Problem Possible Causes What To Do
Dryer doesn't start Dryer is unplugged *Make sure the dryer plug is pushed conq)letely into
the outlet.
Fuse is blown/circuit breaker • Check the household Distribution Panel fllse/circuit
is tripped breaker box in _otu" home, and replace fllse or reset
breaker NOTE"ElectIic dP,'eI_ rise two fllses or breakei_.
Thermal limiter tripped •Check the xent for any obstructions. Call authorized
service i)e_son fin" replacement it necessmy:
Dryer doesn't heat Fuse is blown/circuit breaker • Check the fllse/circuit breaker box in your home,
is tripped; the dryer may tumble and replace both fllses or reset both breakexs.
but not heat Y}mr dryer ulav tuulble if only one fllse is blown or
one breaker tripped.
Gas service is off • Make sure gas shutoff at (hTer and main shutoffare
fitly open.
LP gas supply m_lk is empty •Refill or replace tank. Dryer should heat when utility
or there has been a utility service is restored.
interruption of natural gas
(gas models)
Dryer shakes or Some shaking/noise is normal. • Move dryer to an even floor space, or ac!iust leveling legs
makes noise Dryer may be sitting unevenly as necessary until exen.
Greasyspots on clothes hnproper use of fabric softener •Follow directions on tid)ric softener package.
Drying dirty items with • Use w_tu" dryer to dry only clean items. Dirty items can
deal ones stain clean itelns anti the 'drveI:
Clothes were not • Sometimes stains which cannot be seen when the
completely deal clothes are wet appearafler (hying. Use proper washing
procedures befi)re dr)ing.
Linton clothes Lint filter is full • Clean lint screen before each load.
hnproper sorting • S(m lint i)roduce_s (like chenille) ti'om lint collectms
(like cordm'oy).
Static electricity can attract lint •See suggestions in this section trader STATIC.
Overloading • Separate large loads into smaller ones.
Paper, tissue, etc. left in pockets • Emlm' all pockets betore lmmdering clothes.
Static occurs No fabric softener was used •T_' a lid)tic soflenei:
• gotmce" Fabric Conditioner Dover Sheets have been
approved fin" use in all GE Dryers when used in
accordance with the mamtacmrer's instructions.
OverdJcying •T_' a lid)tic soflene_:
•Ac!iust controls to LESSDRY.
Synthetics, permalent press • T_' a rid)tic soflene_:
mad blends can cause static
2O