GE WH00X5630 Parts list manual

GE Appliances & Lighting
Part Instruction WE49X20697
GE Appliances & Lighting
General Electric Company
Louisville, KY 40225
GEAppliances.com
WH00X5630
Kit Includes
WE1M504 Drum Slides White -2
WE1M1067 Drum Slides Green -2
WE3M26 Top Bearing -1
WE12M29 Drive Belt -1
WE9M30 Drum Felt -1
WH00X5630 Instructions -1
Remove the Dryer Top Panel
The top panel is fastened at the front by 2
screws. On some models it also may be
secured at the rear by 3 lock tabs that
protrude from the bottom of the control
panel.
To remove the top panel:
1. Remove 2 screws that secure the
top panel to the cabinet.
2. Pull the top cover toward you while
lifting up the front edge to release
the side catches. On some models
you may need to slide the top
cover to the left to release it from
the 3 locking tabs.
To remove the front panel:
1. Remove 2 screws from the front
inside edge of the front panel.
2. Tilt the top edge of the front panel
out and disconnect wiring to the
door switch, light, and sensor rods
(if present) as shown below.
To avoid personal injury, disconnect
power before servicing this product.

GE Appliances & Lighting
Part Instruction WE49X20697
GE Appliances & Lighting
General Electric Company
Louisville, KY 40225
GEAppliances.com
WH00X5630
The drum slide assembly is located on the
back side of the front panel and utilizes 4
drum slides. Two white outer slides
WE1M504 are used as guides, and 2 green
center (top) slides WE1M1067 are used to
support the weight of the drum.
Caution: Do not replace the center (top)
support slides WE1M1067 with the white
guide slides WE1M504. Damage to the
dryer will result.
To remove the drum slide top
bearing assembly:
1. Remove the light bulb (if present).
2. Grasp the top of the drum slide
bearing assembly and pull down and
inward to release the assembly from
the 2 tabs located at the top of the
front panel.
3. Reassemble
Drive Belt
The drive belt WE12M22 is a 4-rib belt and
extends from under the motor pulley, over
the top of the idler pulley, and around the
perimeter of the dryer drum. Belt tension is
maintained by the idler pulley and driven
by a pulley attached to the motor shaft.
To remove the drive belt:
1. Reach under the left-hand side of
the drum, push the idler pulley
down and to the right, and lock the
idler arm on the top corner of the
motor bracket to release belt
tension.

GE Appliances & Lighting
Part Instruction WE49X20697
GE Appliances & Lighting
General Electric Company
Louisville, KY 40225
GEAppliances.com
WH00X5630
2. Remove the belt from the motor
pulley and remove through the
front of the dryer.
To install the drive belt:
1. Reach under the left-hand side of
the drum, push the idler pulley
down and to the right, and lock the
pulley shaft on the top corner of
the motor bracket as shown above.
2. Place the belt in position around
the center of the drum through the
front of the dryer.
3. Place the belt in position around
the motor pulley (see below),
release the idler pulley from the
motor bracket, and guide onto the
belt.
Note: Check to make sure the belt is in
place and not twisted before installing the
top and front panels by rotating the drum
by hand. The ribs of the belt should not be
visible on the drum.
Drum Seal/Felt
The drum seal/felt WE9M30 can be
replaced by removing the seal from the
channel located in the air duct assembly.
Wrap any excess felt around the left hand
side of the air duct assembly.