GE Profile Spacemaker JVM1490 User manual

Installation
Instructions Abovethe
CooktopOven
JVM1490,JVM1790,SCAI000,SCAI001
Questions?Call800-GE-CARES(800-432-2737)or visitour _ ebsite at: ge.com I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - S.,e_hese
instructions for local inspector's use.
•IMPORTANT -Obse,,e.ll
go_,ei'iliil o codes _lIl(1 oI'diIl_lIlCes.
• Note to Installer -Be sure to lea',e these
instructions with the (_onsumer.
o
o
o
o
Note to Consumer _ Keep these
instructions for future reterence.
Skill level -Installation of this appliance reqtfires
basic mechanical and electrical skills.
Proper installation is the responsibility of the installer.
Product thilure due to improper installation is not
coxered trader the _arrantx.
LA SECCION EN ESPAI_OL
EMPIEZA EN LA PAGINA 25. READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Installation Instructions
CONTENTS
General information
hnportant Safety Instructions .................................. 3
Electrical Requirements .......................................... 3
Hood Exhaust ...................................................... 4, 5
Damage -Shipment/InstaJlation .............................. 6
Parts Included. ......................................................... 6
Tools You Will Need ................................................ 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate ............................ 8-10
Removing tire Mounting Plate ...................... 8
Finding the _4all Studs ................................. 8
Determining _.lll Plate l.oration .................. 9
Aliguiug the _4hll Plate ............................... 10
Installation Types .................................. 11-22
[]Outside Top ............................
Exhaust 12-14
Attach Mounting Plate to W;dl ....... 12
Preparation of Top Cabinet .......... 13
Checking 1or Proper Damper
()peration ............................................ 13
Mount the Oveu .................... 13, 14
Ac!just the Exhaust Adaptor .......... 14
Connerting Durtwork .......................... 14
_ ()utside Back Exhaust 15-18
Preparing Rear _'V;dl for
Outside Bark Exhaust .......................... 15
Attach Mounting Plate U>_4"01 ...... 15, 16
Preparation of Top Cabinet .......... 16
Adapting Blower tot Outside
Back Exhaust.. .............................. 16, 17
Mount the Oveu .................................. 18
Redrculating ........................................ 19-22
Attach Mounting Plate to _4.fll ....... 19
Preparation of Top Cabinet .......... 19
Adapting Blower
for Redrrulation ......................... 20, 21
Mount the Oveu .................... 21, 22
Installing the Charcoal Filter ...... ........ 22
Before You Use Your Oven .................................. 23
Seccion en Espafiol ........................................ 25-47
2

Installation Instructions
mMPORTANT SAFETY mNSTRUCT ONS
CAWFION: For personal safety, the momlting surface
must be capable of supporting the cabinet load, in
addition to the added weight of this 62%85 pound
product, plus additional oven loads of up to 50 pounds
or a total weight of 117_135 pounds.
CAIYFION: For personal safety, this product c_ot
be installed in cabinet arrmlgements such as an island or
aperfinsuia. It must be mounted to BOTH atop cabinet
AND a wall.
NOTE: For easier insta]iation and personal safety, it is
recommended that two people install tt_s product.
IMPORTANT PLEASE R1LM) CARFFULL_: FOR
PERSONAL SAFETY; THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FNFAL SHOCK.
The power cur'd of this app]iance is equipped with
a three=prong (grounding)
plug which mates with
a standard three=prong
(gromlding) wail receptacle
to mininlize the possibility
of electric shock hazard
from tiffs app]iance.
Insureproper
groundexists
beforeuse
Yon should have the wail receptacle and circuit checked
by aqualified electrician to make sure the receptacle is
properly grounded.
Where a standard two-prong wall _eceptade is
encountered, it is very inlportant to have it replaced
with a properly grounded three=prong wail receptacle,
installed by aqualified electridan.
DO NO% UNDER ANY CIRCUMST_CES, CU_[;
DI_"ORM, OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE ¼rITH
AN FXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rati]/g is 120 volts AC, 60 Hertz, [5 amps, am]
1.70 kilowatts. This product must be co]/m/ected to
a slq_p]} ci]mdt o{ the propervoItq<,e_ am] {reql_e]/c}.
\_ire si zem Ilst CO]/['()]q]/ It) the req Hi rein el/ts of the
Natiomd Electrical Code or tile [)revaiIim/g, local code
for this kilowatt mtim/g. The [)o]ver sIl[)pl_ co]'d amid
>lug sholdd be lu'm]<,ht to a separate 15 to 90= ampere
bra_]c]] circlfit si_]g]e groin]deal ola]et. The ]mt]et box
should be located i_i tile cabim/et above tile ore]/. Tile
outlet box am] suppI} circuit sho_ld be ira/stalled bv
a qlmIilied eIectricim/am[ coului'm to the Nati]mal
Electrical Code ur the prevaili_/g local code.
3

Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages tufty if you plml to vent your exhaust to the outside.
If you plml to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example ot one possible
ductwork instnllation.
DUCT P_ECES EQUIVALENT NUMBER LENGTH x USED
RoofCap 24 Ft. x
12Ft.StraightDuct 12Ft. x
(6" Round)
RectanguhFto-Round 5Ft. x
TransitionAdaptor*
Equivalentlengthsofduct piecesare basedonactualtests and
reflectrequirementsfor goodventingperformancewith anyventhood.
(1)
(1)
(1)
Total Length
EQUIVALENT
LENGTH
24 Ft.
12Ft.
5Ft.
41 Ft.
*IMPORTANT: If a rectangula_to-rotmd transition adaptor is used, the bottom corners of the damper
will ha_e to be cut to fit, usim,._ the tin snips, in order to allow free mo'.ement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example ot one possible
ductwork installation.
[DUC_ PIECES
_Wall Cap
(_ 90° Elbow
EQUIVALENT NUMBER EQUIVALENT
LENGTH* x USED = LENGTH
40 Ft. x (1) 40 Ft.
3 Ft. x (1)3 Ft.StraightDuct
3W' x 10"Rectangular)
10Ft. x (2)
3 Ft.
20Ft.
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood. Total Length = 63 Ft.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
4

Installation Instructions
NOTE: If you need to install ducts, note that the total
duct lengti_ of 3¼" x ]O" rectangular or 6" (liameter
round duct should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following careflfllv.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as possible.
This ensm'es clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with
a standard 3Vt" x 10" rectangular duct.
If a round duct is required, a rectangula>to-rotmd
transition adaptor must be used. Do not use less than
a 6" diameter duct.
Maximum duct length:
For satisfiwtorv air movement, the total duct length of
3¼" x ]0" rectangular or 6" diameter round duct should
not exceed 140 equivalent feet,
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent
to a section of straight duct which is hinter than their
actual physical size. When calculating the total duct
length, add the equiwdent lengths of all transitions and
adaptors plus the length of all straight duct sections.
The chart below shows w)u how to calculate total
equivalent ductwork length using the approximate teet
of equiwdent length of some typical ducts.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5Ft. x ( ) =Ft.
Transition Adaptor
Wall Cap 40 Ft. x ( ) = Ft.
C)_ go° Elbow 10 Ft. x ( ) =Ft.
{_ 45° Elbow 5Ft. x ( ) = Ft.
90° Elbow 25 Ft. x ( ) =Ft.
J 45° Elbow 5Ft. x ( ) =Ft.
Roof Cap 24 Ft. x ( ) = Ft.
Straight Duct 6" Roundor 1Ft. x ( ) = Ft.
3W' x 10" Rectangular
Total Ductwork = Ft.
* IMPORTANT: If' a re( tangulal_to-round transilion E(ltfival( nl 1_ ngths of" du(t pieces are bas(d on aclual tests and
adaplor is use(l, the boltonl colners of lhe (]0Jllp( i l-(:_]ect reqtfir( m( nls lk)r good v( nling performan(e with any
_dll have I0 b( {:tit I1) fit, llSillg the till snips, ill V(llt hood.
(}lXiel I(} allo_ flee lllOV(>l)lelll Of' the ([HlllpeF.
5

Installation Instructions
-SHIPMENT/
mNSTALLATmON
®]If the _it is damaged in shipmenL remr_] the
m_]t to the store im_which it w_s b<mght fi)r repair
ov rep] a ce]_ em_t_
® If the unit is damaged by the customer, repair or
rep];_ceme]_t is the respom_sibi]ity of the cl_stomer.
® ]_f the unit is damaged by the installer (if other
tbam_ the cllstomer), repair or rep]_ceme]_[ mils[
be m:tde by :trram?geme]?[ betweeN? cllstomer am?(]!
im_sta]]er.
PARTS INCLUDED
HARDWARE PACKET
PART QUANTITY
WoodScrews 2
(¼" x2")
ToggleBolts(and 4
wingnuts)(¼" x3")
Self-aligningMachine
Screws(¼"-28x 3¼")
Self-aligningMachine
Screw(¼"-28x2%")
NylonGrommet
(formetalcabinets)
3
2(JVM1790only)
1(JVM1790only)
2
ExhaustAdaptor 1
Damper 1
MetalScrews 1 black
{1_" X I_ 'v) 2 bronze
PowerCordStrap 1
(plastic)
You will find the installation hardware contained in
a packet with the trait. Check to make sure you have
all these parts.
NOTE: Some extra parts are included.
PARTS mNCLUDED
ADDITIONAL PARTS
TOPCABINETTENPLATE
NSTALLA?ION
iNSTRUCTIONS
TopCabinet
Template
RearWall
Template
Installation
Instructions
Separately
Packed
Grease
Filters
QUANTIFY
1
6

Installation Instructions
TOOLS YOU WILL NEED
# 1and#2Phillipsscrewdriver
Tinsnips(forcutting
damper,if required)
Pencil
Scissors
(tocuttemplate,if necessary)
Rulerortapemeasure
aightedge
Electricdrill with 3/16",7716,"
1½-and%" drill bits
Gloves
Studfinder or Hammer(optional)
Carpentersquare
(optional)
Fillerblocksor scrap
woodpieces,if needed
for top cabinetspacing
(usedonrecessedbottom
cabinetinstallationsonly)
Saw(saber,holeor keyhole)
L J Ductandmaskingtape
Safetygoggles Level
MOUNTING SPACE
66" ormore
fromthe floor
tothe top of
theoven
\
Bottomedgeof
cabinetneedsto
be30" or more
fromthe cooking
surface
Backsplash
NOTES:
• The space between the cabinets must be 30" wide
and fl'ee of obst_ uctions.
" If the space between the cabinets is greater
than 30", a Filler Panel Kit may be used to fill
in the gap between the oven and the cabinets.
Your Owner's Manual contains the kit nmnber
foI" VOtlI" model.
" This oven is fin" installation over ranges up to
36" wide.
" If vou are going to vent v(mr oven to the outside,
see Hood Exhaust Section tot exhaust duct
preparation.
" When installing the oven beneath smooth, flat
cabinets, be careful to follow the instructions
on the top cabinet template for power cord
clearance.
" The depth of the opening cmmot be more thml
13-1/2".
7

Installation Instructions
I-]PLACEMENT OF THE MOUNTING PLATE
1"_ REMOVING THE OVEN FROM
THE CARTON/REMOVING THE
MOUNTING PLATE
_ Remoxe the box containing the installation
instructions, filters, exhaust adaptor, damper
and the small hardware bag,. Do not remoxe
the Styrofoam I_r°tecting, the front of the oxen.
[] Fold back all 4 carton flaps full) against carton
sides. Then careflfllx roll the oxen and carton oxer
onto the top side. T'he oxen should be restino, _in
the Styrofoam.
Carton
_Pull the carton up and off the oxen.
[]The motmting plate is attached to the back of the
oxen. Remoxe the two screws holding it to the oxen.
The plate will be used as the rear wall template and
for mounting the oxen to the wall.
[]Set the oven upri *lit Remoxe and properly discard
plastic bags and Styrofoam.
[Open the oxen door and remoxe the styrofoam
pack from inside the oxen. Remoxe the tape
coxering the turntable hub.
I-_ FINDING THE WALL STUDS
enter_
[] Fim_d t]_e studs, usim_g <me of t]_e fo]]OVTim?g
m e[]] (>ds:
A. Stud timider- a magnetic device which
locates m_ai]s.
OR
B. [Ise a hammer to tap ]ighdy across die
mom_tim_g sm'Ii_ce to fim_d a solid som_d.
This will im_dicate a stud ]ocatiom
_Afler the fi_id the bv
]ocatim_g stLld(s), cem_ter
probi_*g the wall with a small m_ailto }h_d the
edges o{ the stud. TheN_ place a mark ha]f\_au
betweeN_ the edges. The cel_ter of am_y a(]jaceN_t
studs sholdd be ]6" or 24" f}'om this mark,
_ Draw a ]im_e dow]_ the cem_ter of the st_ds.
THE OVEN MUST BE CONNECTED TO AT LEAST
ONE WALL STUD.
8

Installation Instructions
DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position - beneath flat bottom
cabinet Plate position - beneath framed recessed
cabinet bottom
Mounting Plate Tabs
_gthe Cabinet Bottom
At least 30", up to 3B"
Mounting Plate Tabs
Touching the Back
Frame
II 30"to Cooktop
Plate position - beneath recessed bottom
cabinet with front overhang
Mounting Plate with
Tabs Below Cabinet
Bottom the Same
Distance as the Front
g Depth
LL
Ill
30" to Cool<top
Your cabinets may have decorative trim that interferes
with the oven installation. Remove the decorative trim
to install the oven i)roperly and to make it level.
THE OVEN MUST BE LEVEL
ILlse a level to make sure the cabinet bottom is level.
If the cabinets have a fl'ont overhang only, with no
back or side fl'ame, install the mounting plate down
the same distance as the fl'ont overhang depth. This
will kee I) the oven level.
[]Measure the inside depth of the fl'ont overhang.
Draw a horizontal line on the back wall equal
distance below the cabinet bottom as the inside
depth of the fi'ont overhang.
[]For this t):pe of installation with fi'ont overhang only,
align the mounting tabs with this horizontal line, not
touching the cabinet bottom as described in Step D.
9

Installation Instructions
ALIGNING THE WALL PLATE
DrawaVertical
LineonWall
-<--from Centerof
TopCabinet
HoleC
CAUTION: _,,Veargloves
to axoid cutting fingeI5 on
sharp edges.
o oo
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
o o o o o oio o o oo ooo
AreaE H01eD
[]Draw a vertical line on tile wall at tile center of tile
30" wide space.
[]Use tile mounting plate as the template for tile rear
wall. Place the mo/mting plate on the wall, making
sure that the tabs are touching the bottom of the
cabinet or the level line drawn in Step C for cabinets
with front overhm_g. Line up the notch mid center line
on the mounting plate to the center line on the wall.
_ \._q/ile holding the mounting plate with one hand,
draw drcles on the wall at holes A, B, C and D (see
illustration above/actual plate marked with arrows).
Four holes must be used for mounting.
[]
NOTE: Holes C and D are inside area E. If neither
C nor D is in a stud, find a stud somewhere in area E
and draw a filil/ circle to line up with the stud. It is
important to use at least one wood screw mounted
firmly in a stud to support tile weight ot tile oven.
Set the mounting plate aside.
Drill holes on the drcles. If there is a stud, drill a '_A¢_"
hole tot wood screws. For holes that don't line up with
a stud, (hill a %" hole fin" toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
10

Installation Instructions
I2-] INSTALLATION TYPES
This oven is designed h>r adaptation to the fi>llowing
3 types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)
(Choose A, B or C)
NOTE: This oven is shiI)ped assembled fin" Outside Top
Exhaust. Select the type of xentilation required for }our
installation and proceed to that section.
OUTSIDE TOP EXHAUST
(VERTICAL DUCT) OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
1Adaptorin Placefor
OutsideTopExhaust
_-] RECIRCULATING
(NON-VENTED DUCTLESS)
A Charcoal Filter Accessory
Kit is required fin" the
non-vented exhaust. (See your
Owner's Manual fin" the kit
number.)
11

Installation Instructions
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Install Adapter
A4. Mount Oven
A5, A(!just Exhaust Adaptor
A6, Connect Ductwork
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw IlltlSt be used to attach the
plate to a wall stud.
[]Remove the toggle wings fl'om the bolts.
[]Insert the bolts into the mounting plate through
the holes designated to go into drDvall and
reattach the toggle wings to :Y," onto each bolt.
To use toggle bolts:
Spacingfor Toggles
MoreThanWall
-@H,_i*_Th ckness
Mounting
Plate,
BoltEnd
_ Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to motmt the plate.
NOTE: Betore tightening toggle bolts and wood
scre_, make sm'e the tabs on the mounting plate
touch the bottom of the cabinet when ptlshed
flush against the wall and that the plate is properly
centered trader the cabinet,
CAUTION: Be careflfl to axoid I)inchin'*_ fingers
between the back of the motmting plate and the wall,
_ Tighten all bolts, Pull the plate awax from the wall
to help tighten the bolts,
12

Installation Instructions
I-_ USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws,
a hole large enough for the power cord to fit thr(m ,h
and a cutout large enough fi_r tile exhaust adaptor.
" Read tile instructions on tile TOP CABINET
TEMPLATE.
" Tape it tmderneath the top cabinet.
" Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safet} goggles when drilling holes
in tile cabinet bottom.
ASSEMBLE AND
INSTALL ADAPTOR
Damper
Exhaust
Adaptor
_,_.:__ BlowerPlate
Bac
[] Place tile oven in its ul)right position, with tile top
of tile unit tacing up.
_Insert the tabs on each side of the damper into the
holes at the inside rear of the adaptor.
_ Attach tile exhaust adaptor to the blower plate with
tile two bronze metal screws provided.
Make sure that the damper pivots easily before
mounting oven.
You will need to make a(!iustments to assure proper
alignment with wmr house exhaust duct atter tile
oven is installed'.
I-_ MOUNT THE OVEN
FOIl EASIER INSTAI,IATION AND PERSONAl,
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your cabinet is metal, use tile nylon
grolUll/et _lro/lnd tile [)()wet" cord hole to l)revent
cutting of tile cord.
NOTE: _4'e recommend using filler blocks if tile
cabinet fl'ont hangs below the cabinet bottom shell
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
NOTE: When mo/mting tile
oven, thread power cord
through hole in bottom
of top cabinet. Kee I) it tight
throughout Steps 1-3.
Do not pinch cord or lift
oven by pulling cord. _I,ifl oven, tilt it
fl_rward, and hook
slots at back bottom
edge onto two lower
tabs of mounting
plate.
/
_Rotate front of o_en
up against cabinet
bottolll.
],_ throughInsert a self-aligniw* screw , top center
cabinet hole. Temporarily secure the oven b)
turning tile screw at least two full turns atter tile
threads haxe ew*aged._, (It will be completel)
tightened later.) Be sure to keep power cord tight.
Be careful not to pinch the cord, especially when
mom_th_g flush to bottom of cabinet.
13

Installation Instructions
MOUNT THE OVEN (continued)
CabinetFront
CabinetBottomShelf
FillerBlock
T quivalentto
Depth
ofCabinet
Recess
Self-AligningScrew
OvenTop
_]Attach tile oveml to tile top cabim/et.
[] Insert 2 sel6aligning screws
(¼"-28 x 3¼") through outer
top cabinet holes. Turn two
fifll turns on each screw.
[
[]Tighten center
screw completely.
NOTE: Use sel6aligning screw, ¼"-28 x 2:'A", on
_[g It
JVM 1790 and self:alignino, _ screws, W'-28 x. /_ ,
on JVM 1490, SCA 1f)00, and SCA 10f) 1.
[] Tightel/ the ol_te_" two sc_'ews to the top of the
ovem (\'_ hi]e tightem/im/g St Ye]ys, h(t](] the ovem/ ira/
I)]ace agai, mist.the wail amld the top cabim/et.)
S/
_]]nstall filte_3. See tile Owner Manualgi'ease
packed with tile oxen.
ADJUST THE EXHAUST
ADAPTOR
Open the top cabinet and a(!iust the exhaust adaptor
t() connect t() tile hotlse duct.
Damper
[-_ CONNECTING DUCTWORK
HouseDuct
_ Extend tile hotlse dtlct do%vn to connect to
tile exhaust adaptor.
] . ,duct tape.Seal exhaust duct ioints using
14

Installation Instructions
OUTSmDE BACK EXHAUST tHorkontaUD.ct}
INSTALLATION OVERVIEW
B1. Prepare P,ear _4"dl
B2. Attach Mounting Plate to X4'all
B3. Prepare Top Cabinet
B4. A_)just Blower
B5. Mom_t the Oven
F_ PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
_Otl need to Ctlt [lIl l b
0 )enino in the rear wall for
outside exhaust.
" Read the instructions on the REAR X4A,I,I,
TEMPI ,ATE.
•Tape it to the rear wall, lining up with the holes
previously drilled tot holes A and g in the wall
plate.
$ ()it the opening, following the instructions of the
REAR X_;_I,I, TEMPI,ATE.
ATTACH THE MOUNTING
PLATE TO THE WALL
i
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to
a wall stud.
_ Remove the toggle wings ti'om the bolts.
_Insert the bolts into the motmting plate through
the holes designated to go into (hwwall and reattach
the toggle wings to '_A"onto each l_olt.

Installation Instructions
To use toggle bolts:
Mounting
Plate
Spacing for Toggles More
-,-I-----_i_ Than Wall Thickness
BToggle Wings
Bolt End
_ Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: geflwe tightening toggle bolts and wood
scre_, make sure tile tabs on tile motmting plate
touch tile bottom of tile cabinet when pushed flush
against the wall and that the plate is properly
centered under tile cabinet.
CAUTION: Be careflfl to axoid pinching fingers
between the back of the molmting plate and the wall.
_ Tighten all bolts. Pull the plate awa) from the wall
to help tighten the bolts.
I-_ USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for tile top support screws and
a hole large enom,h for tile power cord to fit throuoh
" Read tile instructions on tile TOP CABINET
TEMPI,ATE.
" Tape it tmderneath tile top cabinet.
" Drill tile holes, following tile instructions on tile
TOP CABINET TEMPLATE.
CAUTION: _&ear safety goggles when drilling holes
in tile cabinet bottom.
ADAPTING BLOWER FOR
OUTSIDE BACK EXHAUST
_ Remoxe tile three screws that hold tile blower
plate to tile oxen. Slide blower plate from trader
its retaining, flange, . Remoxe and saxe tile screw
that holds blower motor to oxen.
Retaining _<<i_ -_
Flange _ 5_.__F..___ Blower Plate
.......... Motor
[] Carefull) pull out tile blower refit. Tile wires
will extend far enough to allow _ou to a_!just
the blower trait.
BEFORE: Fan Blade
Openings Facing Up
_ Rotate blower trait cotmterclockwise 180 °.
Before Rotation After Rotation
Oven
_ (;entlx tile wires from tile
i'ell/ove grooxes.
Reroute tile wires throu_*h grooxes on other side
of the blower trait.
Before Rerouting After Rerouting
Wires RoutedThrough Right Side Wires Routed Through Left Side
16

Installation Instructions
_Roll the blower unit 90 ° so that tan blade
oi_enings, are thciw,_ out the back of the o'.en.
BeforeRolling _ .
Backof l'_,_r_
Oven Backof Oven
[] I,ocate the two "knockout" plates, on the rear
oven panel, near the top of the oven.
Using tin snips, careflflly ctlt the web area fl'om
the two holes side-by-side (that secm'e the
knockouts to the oven). Cut all flmr webs on both
rear knockouts; this will allow the ventilation tan
airflow to exhaust out the rear of the oven.
CAUTION: Be sure to trim the sharp edges from
the openings after removing the knockout plates.
Oven Rear Panel
Snipall 4webs
on eachknockout
panelandremove
the metalknockouts
for reara_rflow.
_ Place the blm_er trait back into the o )ening.I
AFTER: Fan
Blade Openings
Facing Back
EndA
CAUTION: Do not pull or stretch the blower
refit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openhlgs should
match exhaust openhlgs on rear of oven.
] Replace the blower plate in the same position
as befi_re with the screws.
BlowerPlateScrews
1_ BlowerPlate
/
ii_i-- _1¢ BackofOven
[] Insert the tabs each side of the intodailll) ei"
on
the holes at the inside rear of the adaptor.
Adaptor
_ Attach the exhaust adaptor to the rear of the
o'_en b) sliding it into the guides at the top
center of the back of the oxen.
Damper
ExhaustAdaptor _ _,_._,,.,..,, (hingesideup)
Slideexhaust _J/,/ _,,- Backof Oven
adaptorinto
Tabs Guides
o
Push in securely tmtil it is in the lower locking
tabs. Take care to assure the damper hinge is
installed so that it is at the top and that the
damper swings fi'eelv.
_ Secm'e the exhaust adaptor to the oven with the
two bronze metal screws proxided.
17

Installation Instructions
MOUNT THE OVEN
FOR EASIER INSTAI,I.A_TION AND PERSONAI.
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your (abinet is metal, use the nvlon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet fl'ont hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
NOTE: When m()tmting
the oven, thread power
cord through hole in
bottom of top cabinet.
Kee I) it tight throughout
Steps 1-3. Do not pinch
cord or lilt oven by
pulling cord.
[] I,itt oven, tilt it
fin'ward, and hook
slots at back bottom
edge onto two lower
tabs of m()tmting plate.
_ Rotate fi'ont (If oxen l1 I)
against (abinet bottom.
_Insert a sell=aligning screw through top center
cabinet hole. Tempora_ilv secm'e the oven by
turning the screw at least two full turns alter the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord tight.
Be careful not to pinch the cord, especially when
mounting flush to bottom of cabinet.
CabinetFront
CabinetBottomShelf
FillerBlock
T quivalent
to Depth
of Cabinet
Recess
Self-AligningScrew
OvenTop
_Attach the oxen to the top cabinet.
_Insert 2 self-aligning screws
_I zt
(J/('-98 x. ¼ ) through outer
top cabinet holes. Turn two
till turns on each screw.
U
_ Tighten center
screw completely.
NOTE: Use self-ali.,*ning, screw, ¼"-28 x _2_:' ", on
JVM 1790 and sell=aligning screws, ¼"-28 x 3 V(',
on .[VM 1490, SCA 1f)00, and SCA 1f)f}1.
[] Tighten the outer two screws to the top of the
oxen. (X._bile tightenin(* screws, hold the oxen
in place against the wall and the top cabinet.)
_ Install grease filters. See the Owner's Manual
packed with the oxen.
18

Installation Instructions
RECIRCULATmNG tNon-VentedDuctUess)
INSTALLATION OVERVIEW
C1, Attach M(mnting Plate to _'all
C2. Prepare Top Cabinet
C3. Adjust Blower
C4. Mount the Oven
C5. Install Charcoal Filter (not supplied)
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At
least one wood screw Inust be used to attach the
plate to a wall sttld.
[]Remove the toggle wings fl'om the bolts.
_ Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to :Y{' onto each bolt.
To use toggle bolts:
Spacingfor Toggles
MoreThanWall
+[_-.[.--Th ckness
Wings
Mounting
Plate_
if,
BoltEnd
_ Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to inount the plate.
NOTE: Befl)re tightening toggle bolts and wood
scre_, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered trader the cabinet.
CAUTION: Be careflfl to axoid I)inchiw*_ fingers,
between the back of the motmting plate and the wall.
_ Tighten all bolts. Pull the plate awax from the wall
to help tighten the bolts.
USE TOP CAP4NET TEMPLATE
FOR PREPARATION OF TOP
You need to drill holes for the top support screws and
a hole large enouoh for the power cord to fit throuoh
" Read the instructions on the TOP CABINET
TEM PI,ATE.
" Tape it tmderneath the top cabinet.
" Drill the holes, tollowing the instructions on the
TOP CABINET TEMPLATE.
CAUTION: _ear satety goggles when drilling holes
in the cabinet bottom.
19

Installation Instructions
ADAPTING BLOWER
FOR RECIRCULATION
NOTE: The exhaust adaptor with damper is not
needed fin" recirculating models. You may want to
save them for possible flmu'e use.
[] Remoxe and saxe screws that hold blower plate to
tile O_ eIl,
_ _ Blower Plate Screws
[]Slide tile blower from trader itsplate i'etaining
flange, and lifi it off, Remoxe and saxe screw that
holds tile blower IllOtOI" to o'_en,
Retaining __
Flange _'__v__"__ BI )wer Plate
3_ Carefully pull out tile blower trait. Tile wires
will extend flu" enough to allow xou to adiust the
blower trait.
•( o - I &'
_4 Roll tile blower rant .)0 so that fan blade o )enim*s
-- are fhcing toward the front of the oxen.
BEFORE: Fan Blade
Openings Facing Up_
AFTER: Fan Blade
Openings Facing
NOTE: Make sure wires remain routed in tile
gi'oo_,es of the I/lOtof fI'aIlle,
2O