For answers to your Monogram®or GE®
appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
PHS920SF
GE Profile™ Series 30" Slide-In Induction and Convection Range with Warming Drawer
Specification Created 6/13 220457
Listed by
Underwriters
Laboratories
Dimensions and Installation Information (in inches)
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
*ADA qualified based
on Uniform Federal
Accessibility Standards
*
Receptacle Locations: Locally approved flexible service cord or conduit must be used because
terminals are not accessible after range installation.
See shaded area in drawing for location of
electrical outlet box. Recommended
outlet locations allow range to be installed directly against rear
wall.
Note: This appliance has been approved for 0” spacing to adjacent surfaces above the cooktop.
However, a 6” minimum spacing to surfaces less than 15” above the cooktop and adjacent
cabinet is recommended to reduce exposure to steam, grease splatter and heat.
Installation Information: Before installing, consult installation instructions for current
dimensional data and additional requirements.
MINIMUM DIMENSIONS BETWEEN COOKTOP, WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, ooring and cabinets around the range can withstand the heat (up to 200°F) generated by the
range.
B. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or allow a 24" minimum when
bottom of wood or metal cabinet is protected by no less than 1/4" thick ame retardant millboard covered with not less than No 28 MSG
sheet metal, (.015"), .015" thick stainless steel, .024" aluminum or .020” copper. Acceptable electrical outlet area. Orient electrical receptacle
so the length is parallel to oor.
C. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However, a 6" minimum spacing to surfaces
less than 15" above the cooktop and adjacent cabinet is recommended to reduce exposure to steam, grease splatter and heat.
To reduce the risk of burns or re when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided. If
cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that projects at least 5"
beyond the front of the cabinets.
297⁄8”
36”
3
71⁄4
”
25
7⁄8”
297⁄8”311⁄4”
48
*Depth including door handle is approximately 28-7/8".
*287⁄8”
1⁄4
”
PHS920SF/PS920SF
A
NOTE C
B
A
C
Both
Sides
NOTE: Use a 4' power cord to prevent interference
with unit when installing.
MINIMUM DIMENSIONS BETWEEN COOKTOP, WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, ooring and cabinets around the range can withstand the heat (up to 200°F) generated by the
range.
B. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or allow a 24" minimum when
bottom of wood or metal cabinet is protected by no less than 1/4" thick ame retardant millboard covered with not less than No 28 MSG
sheet metal, (.015"), .015" thick stainless steel, .024" aluminum or .020” copper. Acceptable electrical outlet area. Orient electrical receptacle
so the length is parallel to oor.
C. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However, a 6" minimum spacing to surfaces
less than 15" above the cooktop and adjacent cabinet is recommended to reduce exposure to steam, grease splatter and heat.
To reduce the risk of burns or re when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided. If
cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that projects at least 5"
beyond the front of the cabinets.
297⁄8”
36”
3
71⁄4
”
25
7⁄8”
297⁄8”311⁄4”
48
*Depth including door handle is approximately 28-7/8".
PHS920SF/PS920SF
A
NOTE C
B
A
C
Both
Sides
NOTE: Use a 4' power cord to prevent interference
with unit when installing.
KW Rating
240V 12.2
208V 9.2
Breaker Size
240V 40 Amps†
208V 40 Amps†
†Note: Check local codes for required breaker size.
*Depth including door handle is approximately 28-7/8".
