GE 197D4613P004 Safety guide

ge.com
Beverage Center
and Wine Chiller
197D4613P004 49-60563 04-08 JR
Safety Instructions ...........2, 3
Installation Instructions .......4
Operating Instructions
Control Settings . . . . . . . . . . . . . . . . . . . . .5
Interior Space . . . . . . . . . . . . . . . . . . . . . . .6
Care and Cleaning ............7–9
Replacing the Light Bulb . . . . . . . . . . . . .8
Reversing the Door . . . . . . . . . . . . . . . . . .9
Troubleshooting Tips ......10, 11
Consumer Support
Consumer Support . . . . . . . .back cover
Product Registration (Canada) . .15, 16
Product Registration (U.S.) . . . . . .13, 14
Warranty (Canada) . . . . . . . . . . . . . . . .18
Warranty (U.S.) . . . . . . . . . . . . . . . . . . . .17
Write the model and serial
numbers here:
Model # __________________
Serial # __________________
Find these numbers inside the
beverage center/wine chiller
on the left side.
Owner’s Manual
and Installation
Refroidisseur
àboissons et
àvin
Manuel d’utilisation
et d’installation
Manual del
propietario y
instalación
La section française commence à la page 19
La sección en español empieza en la página 33
Centro
de bebidas
yenfriador
de vinos

PROPER DISPOSAL OF THE BEVERAGE CENTER/WINE CHILLER
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigeration products are still dangerous… even
if they will sit for “just a few days.” If you are
getting rid of your old appliance, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigeration Product:
■Take off the doors.
■Leave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an old
refrigeration product, check with the company
handling the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord.
However,if you must use an extension cord, it is absolutely necessarythat it be a UL-listed, 3-wire
grounding type appliance extension cord having a grounding type plug and outlet and that the electrical
rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including
the following:
■This beverage center/wine chiller must be
properly installed and located in accordance
with these instructions before it is used.
■Do not allow children to climb, stand or hang
on the shelves in the beverage center/wine
chiller. They could damage the beverage
center/wine chiller and seriously injure
themselves.
■Do not storeor use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■Before replacing a burned-out light bulb,
the beverage center/wine chiller should be
unplugged in order to avoid contact with a live
wirefilament.(A burned out light bulb may
break when being replaced.)
■Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■Unplug the beverage center/wine chiller before
cleaning and making repairs.
NOTE: We strongly recommend that any
servicing be performed by a qualified individual.
■Do not store or install this appliance outdoors.
Consumer SupportTroubleshooting
Tips Operating
Instructions Safety Instructions
Installation
Instructions
Care and Cleaning

ge.com
3
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
aqualified electrician to make sure the outlet
is properly grounded.
If you have only a standard 2-prong wall outlet,
it is your personal responsibility and obligation
to haveit replaced with a properly grounded
3-prong wall outlet.
The beverage center/wine chiller should always
be plugged into its own individual electrical outlet
which has a voltage rating that matches the
rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your beverage center/wine chiller
by pulling on the power cord. Always grip plug
firmly and pull straight out from the outlet.
Immediately repair or replace all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the beverage center/wine chiller
away from the wall, be careful not to roll over
or damage the power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer Support
Troubleshooting
Tips
Operating
Instructions
Safety Instructions Installation
Instructions Care and Cleaning

Installing the beverage center/wine chiller.
4
Removing the Packaging
Before using the beverage center/wine chiller, be sure all packing materials and tape
have been removed, including the protective film covering the control and any film
protecting the cabinet.
If you are discarding an old refrigeration product, remove the doors to reduce
the danger of children being trapped inside.
To raise the appliance
■The beverage center/wine chiller can be
freestanding or can be installed under
the counter, with proper clearances.
■Allow the following clearances for ease
of installation, proper air circulation
and electrical connections:
Each side 1/2″(12,7 mm)
Top 2″(51 mm)
Back 2″(51 mm)
■Beforeconnecting the appliance
to the power source, let it stand upright
for approximately 2 hours. This will
reduce the possibility of a malfunction
in the cooling system from handling
during transportation.
■Do not install the beverage center/
wine chiller where the temperature
will go below 55°F (12,7°C) or above
90°F (32,2°C). If the room temperature
is below the temperature setting, the
beverage center/wine chiller will not
operate (for instance, if the room is
at 55°F (12,7°C) and the setting is 60°F
(15,6°C), the unit will not run).
■Install it on a level floor.
■Do not install the beverage center/wine
chiller where it will be subject to direct
sunlight, heat or moisture.
■Do not storeor install this appliance
outdoors.
Installation Guidelines
Adjustable legs at the front corners
of the beverage center/wine chiller
should be set so the beverage center/
wine chiller is firmly positioned on the
floor, with a 1/8″tilt to the back to help
the door closure.
To adjust the leveling legs, turn the legs
counterclockwise to raise the beverage
center/wine chiller,clockwise to lower it.
Leveling Legs
Consumer SupportTroubleshooting
Tips Operating
Instructions Safety Instructions
Installation
Instructions
Care and Cleaning
The door handle and screws areshipped
in a hardware bag attached to one
of the shelves inside the cabinet.
Locate the door handle and twoscrews.
Secure the door handle to the side
of the door as shown.
Door Handle
Screw
Door
Handle

You can turn the light ON or OFF by pushing the
light switch located on the right side of the control
panel housing. If the interior light is left on,
it will raise the inside temperature.
About the control and settings. ge.com
Consumer Support
Troubleshooting
Tips
Operating
Instructions
Safety Instructions Installation
Instructions Care and Cleaning
Control Settings
The temperature range of the beverage center/
wine chiller is intended for 40°F (4,4°C) to 60°F
(15,6°C). The display shows the average
temperature of the appliance. It is normal
for the actual temperature to vary slightly
during operation.
Auto Temperature Setting
When the appliance is plugged in or the “+” pad
is pressed, the appliance runs on the “Auto Bev”
setting of 44°F (6,7°C) and the “Auto Bev”
indicator light in the upper left corner stays lit.
NOTE: Display will flash when the “+” pad is
pressed.
Normal Temperature Setting
The temperature of the beverage center can
be set anywherebetween 39°F (3,9°C) to 61°F
(16,1°C) by the “+” and “–” pads.
Press and hold the SET pad. You will hear
aseries of 2 beeps.
After the second beep, press the “+” and “–”
pads to increase or decrease the desired
temperature in increments of one degree.
During this time the display will flash.
Press SET to confirm your choice. The display
will stop flashing. If no confirmation is made
in ten seconds, the unit will automatically
accept your change.
NOTE: When you change the temperature
setting, there may be a 5-minute delay until
the compressor starts to run.
Fahrenheit and Celsius
The temperature display can be changed
between Fahrenheit and Celsius by pressing and
holding the “+” pad for approximately 5 seconds.
Indicator Light
The indicator is lit when the compressor is
running to cool your unit.It will not be lit when
the compressor is idle.
Interior Light
Toswitch the interior light on/off,simply press
the pad.
5
Interior Light
Auto Bev
Indicator Light
After plugging in the beverage center/wine
chiller and setting the desired temperature,
allow the beverage center/wine chiller to reach
the set temperature before loading your wine.
The temperature may take up to 12 hours to
completely stabilize.
After loading the wine or beverages, you may
notice the actual temperature rise. This is normal.
The actual temperature will continue to change
as the wine and beverages are cooled to the set
temperature. The temperature may take up to
12 hoursto completely stabilize.
Aguide with wine serving temperature suggestions
is located on the inside right portion of the unit.
It gives recommended temperatures for different
wines, as well as instructions on adjusting the
temperature of the beverage center/wine chiller.
NOTE: The exterior of the cabinet may get warm.
This is normal.
When the Beverage Center/Wine Chiller is Plugged In

6
Consumer SupportTroubleshooting
Tips Operating
Instructions Safety Instructions
Installation
Instructions
Care and Cleaning
About the interior space.
As with any refrigeration product, there
is a slight temperature variance at different
locations within the cabinet.
Wine and Beverage Loading
Suggested bottle arrangement
for wine–full load (holds 31 wine
bottles)
Suggested arrangement for other
beverages–full load (holds 109
beverages)
Wooden shelves in the beverage center/
wine chiller are removable for easy
cleaning and for storing larger items.
To remove a shelf, open the door
completely to avoid potential damage
to the shelf. Lift slightly and pull the shelf
forward. The shelf may fit tightly in the track.
To replace a shelf, open the door completely
to avoid potential damage to the shelf.
Slide the shelf into the tracks along
the sides of the cabinet until it stops.
Wooden Shelves

7
Care and cleaning. ge.com
Consumer Support
Troubleshooting
Tips
Operating
Instructions
Safety Instructions Installation
Instructions Care and Cleaning
IMPORTANT: Unplug the beverage
center/wine chiller before cleaning.
Keep the outside clean. The cabinet
can be washed with mild soap and water.
Clean with a damp cloth. Never use
abrasive scouring powders.
Use a glass cleaner or mild soap and water
and a soft cloth to clean the glass door.
Do not use any abrasive powders.
Do not wipe the beverage center/wine
chiller with a soiled dishcloth or towel.
These may leave a residue that can
erode the paint. Do not use scouring pads,
powdered cleaners, bleach or cleaners
containing bleach because these products
can scratch and weaken the paint finish.
Protect the paint finish. The finish
on the outside of the beverage center/
wine chiller is a high-quality, baked-on
paint finish. With proper care, it will stay
new-looking and rust-free for years. Apply
acoat of kitchen/appliance wax when the
wine chiller is new, and then at least twice
ayear.
Cleaning the Outside
IMPORTANT: Unplug the beverage
center/wine chiller before cleaning.
To clean the inner liner and racks, use
awarm water and baking soda solution—
about one tablespoon (15 ml) of baking
soda to a quart(1 liter) of water.This both
cleans and neutralizes odors. Clean with
adamp cloth.
The vinyl door gasket may be cleaned
with mild soap and water or a baking soda
solution.
Do not use detergents, scouring powders,
spray cleaners or other harsh chemicals
toclean the interior.
To avoid water stains on the wood
shelves, clean up and dry any liquid spills
immediately.
Wipe the control panel with a damp
cloth. Dry thoroughly. Do not use cleaning
sprays, large amounts of soap and water,
abrasives or sharp objects on the panel—
they can damage it.Some paper towels
can also scratch the control panel.
Cleaning the Inside
Defrost whenever frost on the inside
surfaces of the storage area becomes
1/8″(3 mm) thick.Never use a heater
of any kind, scraper or sharp instrument
to remove frost as it may damage
the beverage center/wine chiller.
Todefrost,unplug the beverage center/
wine chiller. Remove the contents and wipe
inside surfaces and racks with a clean
towel. If frost does not come off easily,
allow the frost to melt somewhat and
wipe off.
After defrosting, make sure inside surfaces
are dry; then return the contents to the
beverage center/wine chiller and set the
temperaturecontrol to the desired setting.
NOTE: The drain pan above the compressor
may be full following defrost. Check to
makesureno water spills when moving
the unit.
Defrosting

8
Consumer SupportTroubleshooting
Tips Operating
Instructions Safety Instructions
Installation
Instructions
Care and Cleaning
Care and cleaning.
If the power fails, open the door as
infrequently as possible to maintain
the temperature. A gradual rise in
temperature should not have any
adverse effect on the wine.
If it is extremely hot, you may want to
unload the wine from the beverage
center/wine chiller and move the wine
to a cooler location until power is restored.
The controls may maintain your
temperature settings when the power
has been restored. If your settings are not
correct, reset according to the Control
Settings section.
In the Event of a Power Failure
Unload the wine, then secure the racks by
taping them in place to prevent damage.
Be sure the beverage center/wine chiller
stays in an upright position during the move.
Preparing to Move
Replacing the light bulb.
Unplug the beverage center/wine chiller.
Remove any beverages and shelves as needed for access.
The light bulb is located behind a light shield in the ceiling of the
beverage center/wine chiller near the back.To remove the light
shield, remove the screw on the right side of the light shield.
Pull down on the back of the light shield to release the twofront tabs.
Unscrew the light bulb from the socket.
Replace with a 15 watt, 120 volt bulb. This type of bulb is available
at most hardware and automotive parts stores.
WARNING: Using a bulb rated higher than 15 watts may
damage the electronic controls on the beverage center/wine chiller.
Reinstall the light shield.
Replace the top shelf and beverages.
Plug in the beverage center/wine chiller.
Light Shield
Screw

9
Reversing the Door. ge.com
Consumer Support
Troubleshooting
Tips
Operating
Instructions
Safety Instructions Installation
Instructions Care and Cleaning
Unplug the beverage center/wine chiller.
Tape the door shut with masking tape to secure alignment.
Remove the top hinge cover by removing the screw.
Remove the 2 screws securing the top hinge to the frame.
Lean the beverage center backward to access the bottom hinge.
Remove the 2 screws securing the bottom hinge assembly to the
frame.
NOTE: If you lay the unit on its back, be sure to let it stand upright for
at least 2 hours before connecting to the power source; this will reduce
the possibility of a malfunction in the cooling system.
Remove the Plug Button from the top left side of the door.
Install the Plug Button into the hinge hole on the right side.
Press firmly to secure.
If the handle has been installed, remove it and install it
on the opposite side. Refer to Door Handle section for instructions.
Hold the door securely in place and install the bottom hinge
on the opposite side.
Install the top hinge and cover on the opposite side. Makesure
the door is aligned with the cabinet beforetightening the screws.
Remove the tape. Open and close the door to check alignment with
the cabinet.If necessary, loosen the screws on the bottom hinge,
realign the door, and retighten the screws.
Plug in the beverage center/wine chiller.
NOTE: If you had to lay the unit on its back, be sure to let it stand
upright for at least 2 hoursbeforeconnecting it to the power source;
this will reduce the possibility of a malfunction in the cooling system.
Set the temperaturecontrols to the desired setting.
Hinge cover
Top Hinge
Bottom Hinge
Plug Button
Bottom
Hinge
Leveling Leg
Screw

Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
10
Before you call for service…
Problem Possible Causes What To Do
Appliance does not Appliance is unplugged. •Push the plug completely into the outlet.
operate and the display The home circuit breaker •Replace fuse or reset the breaker.
is blank is tripped/the fuse is blown.
Vibration or rattling Appliance is on •See the Leveling Legs section.
(slight vibration an uneven surface.
is normal)
Motor operates for Normal when appliance •Wait 12 hours for the appliance to completely
long periods or cycles is first plugged in. cool down.
Often occurs when large •This is normal.
amounts of wine are placed
in appliance.
Door left open. •Door is not self-closing. Always makesurethat
the door is closed after opening.
•Check to see if a bottle is holding door open.
Hot weather or frequent •This is normal.
door openings.
Temperature control set •See About the control and settings.
at the coldest setting.
Appliance is too close •See the Installation Guidelines section
to the wall. for the correct clearances.
Appliance too warm Normal when appliance •Wait 12 hoursfor the appliance to completely
is first plugged in. cool down.
Often occurs when large •This is normal.
amounts of wine are placed
in appliance.
Temperature control •See About the control and settings.
not set cold enough.
Warm weather or frequent •Set the temperature control one step colder.
door openings. See About the control and settings.
Appliance is too close •See the Installation Guidelines section
to the wall. for the correct clearances.
Door left open. •Door is not self-closing. Always makesurethat
the door is closed after opening.
•Check to see if a bottle is holding door open.
Appliance does not Setting is aboveroom •This is normal. If wine or beverages are too warm,
operate, but the display temperature. change the temperature setting to a lower temperature.
is lit and functioning
Consumer SupportTroubleshooting
Tips Operating
Instructions Safety Instructions
Installation
Instructions
Care and Cleaning