GE Monogram ZDW24 WW User manual

GE Monogram®
Installation
Instructions
Wine Chiller
Model
ZDW24 WW
ZDW24 BB

WARNING
2
Before you begin—Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector’s use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future
reference.
If you have questions concerning the installa-
tion of this product, call the GE Answer
Center®Consumer Information Service at
800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged wine chiller, you
should contact your dealer.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See the Use & Care
Guide for warranty information.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
Contents Design Information
Models Available.................................................................................................................................. 3
Dimensions and Clearances ............................................................................................................... 3
Installation Preparation
Grounding the Wine Chiller .............................................................................................................. 4
Reverse Door Swing ............................................................................................................................ 5
Installation
Step 1: Remove the Packaging ........................................................................................................... 6
Step 2: Install Handle ......................................................................................................................... 6
Step 3: Install Leveling Legs ............................................................................................................... 7
Step 4: Slide the Unit into the Cutout ............................................................................................... 7
•Il ne faut utiliser cet appareil que pour
l’usage pour lequel il a été construit.
•Il faut réparer ou remplacer
immédiatement tout cordon
d’alimentation électrique effiloché ou
endommagé.
•Débrancher le réfrigérateur à vin avant le
nettoyage ou toute intervention.
•Les réparations doivent être faites par un
technicien qualifié.
CAUTION
WARNING
This appliance must be properly grounded. See “Electrical Supply”, page 4.
CAUTION
ATTENTION
Cet appareil doit être correctement mis à la terre.
Consulter « Alimentation électrique », page 4.
• Use this appliance only for its intended
purpose.
• Immediately repair or replace electric
service cords that have become frayed or
damaged.
• Unplug the wine chiller before cleaning
or making repairs.
• Repairs should be made by a qualified
service technician.
ATTENTION

3
Design Information
Wine Chiller
Model
Available
ZDW24 WW
White Wine Chiller
ZDW24 BB
Black Wine Chiller
Dimensions
& Clearances
Front ventilation allows the wine chiller
to be installed as a built-in and still operate
efficiently.
The bottom front grille area must remain
unobstructed for proper air circulation and
operation.
Cutout dimensions shown allow for a full door
swing and access to the pull-out racks.
The Monogram wine chiller adds an eloquent
statement of style, convenience and flexibility.
The Monogram wine chiller can be used
freestanding or as a built-in.
Locate
Outlet
34-1/2"-35"
24" Min.
24" Min.
5"
34-1/2"
24-1/8" 23-7/8"
Installation
Options
Increase storage capacity by installing two
Monogram wine chillers side by side. Or,
install the wine chiller next to a Monogram
beverage center for a complete refreshment
center.
A side by side installation requires a 48" wide
opening. No trim kits required.
•The glass door fronts should align evenly
with adjacent cabinet door fronts.
Frameless Cabinets:
• If installing between frameless cabinets, a
1/2" wide filler strip or side panel may be
required. The filler strip will act as a spacer
between the door case and adjacent cabinet
and will prevent interference with cabinet
door swing. The width of the opening must
include filler panels.
Provide two separate properly grounded
electrical outlets for a side by side installation.
Each electrical outlet should have a voltage
rating that matches the rating plate.

4
Installation Preparation
Wine Chiller
Grounding
the
Wine Chiller
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
The power cord of this appliance is equipped
with a three-prong (grounding) plug which
mates with a standard
three-prong (grounding)
wall receptacle to minimize
the possibility of electric
shock hazard from this
appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encoun-
tered, it is your personal responsibility and
obligation to have it replaced with a properly
grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
Use of Adapter plug
Because of potential hazards under certain
conditions, we strongly recommend against
use of an adapter plug. However, if you still
elect to use an adapter, where local codes
permit, a TEMPORARY CONNECTION, may
be made to a properly grounded 2-prong wall
outlet by use of a UL listed adapter available
at most hardware stores.
The larger slot in the adapter must be aligned
with the larger slot in the wall outlet to
provide proper polarity in the connection of
the power cord.
Use of an adapter plug will increase the
cutout depth required.
Align Large Prongs/Slots
Insure Proper Grounding and Firm
Connection Exists Before Use
Brancher la borne de terre d’un
adaptateur sur la vis du couvercle de la
prise murale ne met pas l’appareil à la
terre, sauf si la vis du couvercle est
métallique, n’est pas isolée et si la prise
murale est mise à la terre par
l’intermédiaire des fils de la maison. Il faut
faire vérifier le circuit par un électricien
qualifié pour s’assurer que la prise est
correctement mise à la terre.
When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand and pulling the power cord with the
other hand. If this is not done, the adapter
ground terminal is very likely to break with
repeated use.
Should the adapter ground terminal break, DO
NOT USE the appliance until a proper ground
has again been established.
Use of Extension Cords
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord. However,
if you still elect to use an extension cord, it is
absolutely necessary that it be a UL listed 3-wire
grounding type appliance extension cord
having a grounding type plug and outlet and
that the electrical rating of the cord be 15
amperes (minimum) and 120 volts.
Attaching the adapter ground terminal to
a wall outlet cover screw does not ground
the appliance unless the cover screw is
metal, and not insulated, and the wall
outlet is grounded through the house
wiring. You should have the circuit
checked by a qualified electrician to make
sure the outlet is properly grounded.
CAUTION PRUDENCE

5
To remove the door:
•Remove the top hinge pin using a 1/8" allen
wrench. Set aside.
•Lift the door off the bottom hinge.
•Re-install the top hinge pin.
•Remove the top hinge and re-install on the
bottom left side. Remove the bottom hinge
and re-install on the top left side.
•Insert the supplied plug buttons into the old
hinge holes, top and bottom.
The light trigger on the bottom of the door
must be removed and secured to the opposite
end.
•Remove the light trigger by backing out 2
screws. Set the trigger and screws aside.
•Install screws from plastic bag packed with
Use & Care Guide into light trigger holes.
•Turn the door upside down.
•Measure and mark 12-1/4" and 13" from the
right side (or 3/4" from the first location).
Measure and mark 11/16" from the front
side of the door. See illustration.
•Drill holes with 5/32" drill bit.
•Install the light trigger with original screws.
•Remove the top hinge pin using the 1/8"
allen wrench.
•Place the door onto the bottom hinge, and
install the top hinge pin with allen wrench.
•Open and close door to test door swing. If
door drags and does not close evenly, loosen
hinge screws and slip shims behind the
hinge. Tighten screws and test again.
Position new nameplate:
•Remove the original nameplate, now located
on the bottom of the door.
•Locate the template packed with the parts
package to position the new monogram
nameplate.
•Hold or tape template behind glass door.
•Remove backing from Monogram name-
plate.
•Place nameplate onto front side of door,
matching illustration on template.
Reverse
Door
Swing
Installation Preparation
Wine Chiller
Top Hinge
Bottom Hinge
Light Trigger
Top of the Door
12-1/4"
Front of the Door
3/4"
11/16"
Slip Shim
Behind Hinge
Top of Name Plate Top of Glass Door
Door Frame Side
P/N 41005263
Upper Left
Corner of
Glass
DOOR
NAME PLATE
LOCATION

Remove all packing material and tape.
Tools and materials required:
• #2 Phillips screwdriver
Parts List:
A. Stainless tubular handle
B. 2 Handle standoffs
C. 3 Screws for mounting handle standoffs
(2 required, 1 extra)
D. 3 Set screws (2 required, 1 extra)
E. 3/32" Allen wrench for set screws
F. 4 U-Clips
G. 4 Leveling legs
H. GE Monogram nameplate
I. 8 Plug buttons
J. Hinge Shims
K. Template for Nameplate Location
L. 2 Screws for light trigger hole
6
Installation
Wine Chiller
Remove the
Packaging
1
Step
A.
B. C.
D.
E.
F.
G.
H.
Install
Handle
2
Step
Note: Consider door swing direction. If you wish to change door
swing, complete the instructions shown on page 5 before installing
the handle.
• Place handle standoff against the top screw hole
in the door. Position the standoff so that the
small screw hole points toward the floor.
•Drive screw through the standoff and into the
door. Do not tighten.
•Install bottom standoff. Do not tighten.
•Place handle to standoffs so that handle mount-
ing posts are inserted into the standoffs. The
handle should fit into the curved shape of the
standoff. Again, the set screw hole should be
pointing downwards.
•Remove the handle and tighten standoffs to
door.
•Place handle to standoffs and install set screws
through the bottom of standoffs using the allen
wrench provided.
•The handle should be tight against the standoff.
•Save the allen wrench for future use.
Screw
Allen Wrench
I.
J.
K.
Top of Name Plate Top of Glass Door
Door Frame Side
P/N 203C5444P001
PUB. 31-45280
Upper Left
Corner of
Glass
DOOR
NAME PLATE
LOCATION
L.
CAUTION: Small objects are a choke
hazard to children. Remove and
discard any parts not used.
PRUDENCE – Les petits objets
peuvent étrangler les enfants. Il faut
jeter toutes les pièces qui ne sont pas
utilisées.

7
Slide the
Unit into
the Cutout
4
Step
•Move the wine chiller close to the opening.
•Connect the power cord plug to the properly
grounded receptacle.
•Slide the unit into the opening.
3
Install
Leveling
Legs
Step
Lay the wine chiller on its back.
•Slide a U-clip into each of the 4 corner holes on
the bottom.
CAUTION: See illustration. Be sure the tangs on
the clips are on the outside and the straight
portion inserted into the holes.
•Screw the leveling legs into the U-clips all the
way until snug. Then, adjust the leveling legs to
installation height.
Installation
Wine Chiller
A.
B.
C.
D.
Monogram

Pub. No. 49-6980-1
Part No. 197D1760P001
 1999 GE Appliances
(N.D. 365) 2/99
41005935
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
To obtain specific information concerning any
Monogram product or service, call GE Answer Center®
consumer information service at 800.626.2000—any
time, day or night.
For Monogram local service in your area, call
1-800-444-1845.
NOTE: Product improvement is a continuing endeavor at General
Electric. Therefore, materials, appearance and specifications are
subject to change without notice.
Monogram.
®
General Electric Company
Louisville, KY 40225