Gefen DVI-441DLS User manual

4x1 DVI DL
Switcher
with Serial Option
USER MANUAL
www.gefen.com

Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
[email protected]
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
4x1 DVI DL Switcher is a trademark of Gefen Inc.
© 2007 Gefen Inc., All Rights Reserved
ASKING FOR ASSISTANCE

TABLE OF CONTENTS
Introduction
Features
Panel Descriptions
Connecting and Operating the 4x1 DVI DL Switcher
RMT4-IR Installation
Dip Switch Guide
Operation Notes & Troubleshooting
RS-232 Interface
Specifications
Warranty
1
2
3
4
5
6
7
8
9
10

Congratulations on your purchase of the 4x1 DVI DL Switcher. Your complete satisfac-
tion is very important to us.
Gefen’s line of KVM (Keyboard Video & Mouse), DVI, ADC, USB, switches, extenders,
converters and hubs is designed to make computer use more comfortable, more pro-
ductive and less expensive. KVM switches allow access to multiple computers from a
single keyboard, while the extenders give the user control over a computer up to 330
feet away from the work area. The ex•tend•it line offers solutions for noise, space and
security concerns, data center control, information distribution, conference room presen-
tation, and school and corporate training environments.
Our Commitment
Gefen will always offer the finest quality product at the best possible price. Included in
that price is a lifetime of free support from a team of outstanding engineers.
Now you can switch easily and reliably between any combination of four dual link DVI
& USB 2.0 equipped computers (PC or Mac) - using only one keyboard, display and
mouse. The DL cross platform switcher saves space - there’s no need to work on a desk
crowded with double displays, keyboards and mouse devices. It saves time - there’s no
need to move from one monitor to another to access different computers.And, it saves
money - there’s no need to purchase additional displays, mouse devices, keyboards etc.
INTRODUCTION
1

FEATURES
Features
• Switches easily between any four dual link DVI computers with USB 2.0 and audio
• Maintains highest 3840 x 2400 resolution dual link video
• Saves you money on hardware costs
• Use either PC or Mac USB 2.0 keyboard/mouse
• Discrete IR remote (included)
• RS-232 remote port
• Supports DDWG standards for DVI monitors
• Installs in minutes
• Includes Rack Ears
Includes:
(1) 4x1 DVI DL Switcher
(1) 5V DC Power Supply
(1) RMT4-IR Remote Control
(4) 6ft Dual Link DVI cables
(4) 6ft USB cables
(4) Audio Cables
(1) Set of Rack Ears
2

PANEL DESCRIPTIONS
3
Power
Indicator
Infrared
Sensor Indicates which
input is selected
RS-232 Interface
5V DC
Input DVI In 1 DVI In 2 DVI Out USB
Outputs
DVI In 3 DVI In 4 USB
Inputs IR Extender
Port
Buttons to select inputs 1 through 4
Audio Out
Audio In 4Audio In 3Audio In 2
Audio In 1

CONNECTING AND OPERATING THE 4x1 DVI DL SWITCHER
How to Connect the 4x1 DVI DL Switcher to your devices
1- Connect the supplied cables from your first computer into the DVI In 1, USB In 1,
and Audio In 1 connection in the back of the DVI Switcher.
2- Repeat step one for up to four computers on inputs 2-4.
3- Connect the monitor to the DVI Out connection.
4- Connect your USB devices (e.g. keyboard, mouse) into the USB Out.
5- Connect your speakers to the Audio Out.
6- Plug the 5VDC power supply into the 4x1 DVI DL Switcher.
How to Operate the 4x1 DVI DL Switcher
1- Use the RMT4-IR remote control port to remotely switch between sources.
2- Use the RS-232 interface with a compliant device to switch between sources.
4

RMT4-IR INSTALLATION
5
1. Remove battery cover from the back of the RMT4-IR remote.
2. Verify that dip switches 1 & 2 are in the down (OFF) position.
3. Insert the battery, hold the battery so that you can see the positive side facing up. The
side that is not marked must be facing down.
4. Test the RMT4-IR remote by pressing ONLY one button at a time. The indicator light
on the remote will flash once each time you press a button. WARNING: Do not press
multiple buttons simultaneously and do NOT press buttons rapidly. These actions will
cause the remote to reset and steps 1-4 will have to be repeated.
Note: The RMT4-IR ships with two batteries. One battery is required for operation, the
second battery is complimentary.
How to Operate the IR Extender Eye (optional)
Plug in the IR extender eye to the extender port on the back of the switcher. As soon as
the IR extender eye is plugged in you can extend your IR signal. The IR extender eye
does not come included in the package.

DIP SWITCH GUIDE
if you are experiencing Infrared interference, you can change the IR code on the Re-
mote and the 4x1 DVI DL Switcher itself.
To change the IR code on the RMT4-IR, simply remove the battery cover and find the 2
dip switches just above the batteries. These switches correspond to a set of switches
on the 4x1 DVI DL Switcher.
To change the IR code on the 4x1 DVI DL Switcher, look under the unit and find a silver
sticker. Beneath this sticker is a group of 4 dip switches. The first 2 switches (labelled 1
and 2) correspond to the 2 switches found on the RMT4-IR remote control.
The following are the 4 Infrared channels possible for both the RMT4-IR and the
4x1 DVI DL Switcher. The dip switches on both the remote and the switcher itself must
match in order to be operational.
12
Channel 0:
12
Channel 1:
12
Channel 2:
12
Channel 3:
6

7
USB
If your USB stops functioning correctly, you can manually re-initialize the USB hub in
the switch by pushing twice on the channel select button, that corresponds with the
channel that the switcher is pointed at, on the front of the unit. This will cause the
channel selected LED to blink once letting you know the USB hub has been
re-initialized.
To have the USB re-initialize automatically every time you switch, look under the 4x1
DVI Switcher and locate the blank sticker. Peel it off to reveal a bank of four dip switch-
es. Find the dip switch labeled “4” and flip it to the ON position. Now every time you
switch the hub will re-initialize itself.
Video
When turning on or rebooting your computers, the 4x1 DVI DL Switcher must be se-
lected to the computer that is booting until the computer completes the boot cycle. This
step can be eliminated using the Gefen DVI Detective.
If you loose your picture when you switch between sources you will need a DVI
Detective.
To switch between Dual Link and Single Link sources, a Single Link cable (sold
separately) must be used for each Single Link source connected to the switcher.
OPERATION NOTES & TROUBLESHOOTING