Gemmy Orchestra of Lights-Lightshow Projection User manual

E-1
IMPORTANT: PLEASE READ ALL THE
INSTRUCTIONS CAREFULLY BEFORE
USING THIS PRODUCT.
Failure to follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
WARNING: Not recommended for children under 12 years of age. As
with all electric products, precautions should be observed during handling and use to prevent electric shock.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN THE COVER. NO USER
SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING: This product is recommended for indoor and outdoor use. Please read this manual carefully
prior to using the unit.
WARNING:
1. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
2. Do not let lamps rest on the supply cord or on any wire.
3. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
4. Do not cover the product with cloth, paper or any material not part of the product when in use.
5. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified
electrician for proper installation.
6. This seasonal use product is not intended for permanent installation or use.
7. Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
8. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
9. This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with
or placed where small children can reach it.
10. Do not use this product for other than its intended use.
11. Do not hang ornaments or other objects from cord, wire, or light string.
12. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product.If the
replacement fuse blows, a short-circuit may be present and the product should be discarded.
13. Th is product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug
will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Do not use with an extension cord unless plug can be fully inserted. Do not alter or replace.
14. Read and follow all instructions that are on the product or provided with the product.
Orchestra of Lights-Lightshow Projection

E-2
CAUTION: To reduce the risk of fire and electric shock:
1. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal.
2. Do not mount or support wires in a manner that can cut or damage wire insulation.
USE AND CARE INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in
which the needles are brown or break off easily. Keep the tree holder filled with water.
2. If the product is placed on a tree, the tree should be well secured and stable.
3. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product from wherever it is placed, to avoid any undue strain or stress
on the product conductors, connections, and wires.
5. When not in use, store neatly in a cool, dry location protected from sunlight.
CONTENTS
Projection™1pc
Fuse 2pcs
Stake 5pc
Circle 5pc
ASSEMBLY INSTRUCTIONS
1. Gently remove contents from packaging and lay out in a clear area.
2. Assemble the light stake parts A as shown in illustration 1, Push the A parts together until tighten the screws.
3. Push A through the circle, insert the grooves of projection™, and tighten the circle,then adjust the angle of projection™
4. Plug power cord into standard wall socket. (See illustration 2)
5. Unplug when not in use.
BUTTON INSTRUCTIONS
1. BLUETOOTH - Press to turn ON/OFF bluetooth mode.
2. INCREASE THE VOLUME - Make the music louder.
3. REDUCE THE VOLUME - Make the music quieter.
4. PLAY/PAUSE - Play or pause the music. Light will turn OFF when music stops.
5. PREVIOUS SONG - Play the previous song.
6. NEXT SONG - Play the next song.
illustration 1
illustration 2
AAAA A

E-3
USER SERVICING INSTRUCTIONS
Fuse Replacement
WARNING: Risk of Fire: Replace only with same size and type of fuse.
WARNING: Risk of Fire: Do not replace the attachment plug. Contains a
safety device (fuse) that should not be removed. Discard product if
attachment plug is damaged.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by
pulling on the cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug towards blades. (See illustration)
3. Remove fuse carefully.
4. Replace fuse only with 5 Amp Max, 125 Volt fuse (provided with product)
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment plug.
OPERATION
- Insert the plug into socket.
- Set this device as a projector.
- Extract the plug if not in use. Be careful with the power cord!
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting
defects or problems. Keep away from heaters and other heating sources! If the device has been exposed to drastic temperature
fluctuation (e.g. after transportation), do not switch it on immediately. Leave the device switched off until it has reached room
temperature. Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified
persons are not subject to warranty. Keep young children and amateurs away from the device!
WARNING
This device complies with Industry Canada license exempt RSS standard(s).Operation is subject to the following two conditions: (1)
This device may not cause interference, and (2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
This radio transmitter (ISED certification number: 7137C-113746) has been approved by Industry Canada to operate with the
antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this device.
WARNING: CAN ICES-005(B)
THESE INSTRUCTIONS ARE FOR THESE ITEMS
11374 6
QDID: 91274
Working
Fuse
Replace
Fuse
Visit WWW.GEMMY.COM for more information.
©2018 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 [phone]
MADE IN CHINA
PRINTED IN CHINA