Gemmy AIRBLOWN INFLATABLE User manual
IMPORTANT SAFETY
INSTRUCTIONS
BASIC PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED WHEN USING ELECTRICAL PRODUCTS,
INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
• This is an electrical product - not a toy! To avoid risk of
fire, burns, personal injury, and electric shock, it should
not be played with or placed where small children can
reach it.
• Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is
not provided, contact a qualified electrician for proper
installation.
• This seasonal use product is not intended for permanent
installation or use.
• Do not mount or place near gas or electric heaters,
replaces, candles, or other similar sources of heat.
• Do not secure product wiring with staples or nails or place
on sharp hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring
for the night, or if left unattended.
• Do not use this product for other than its intended
purpose.
• Do not hang ornaments or other objects from cord, wire,
or light string.
• Do not close doors or windows on the product, or
extension cords, as this may damage the wire insulation.
• Do not cover the product with a cloth, paper, or any
material not part of the product when in use.
• Do not place the product against carpeting, furniture, or
any other fabric when in use.
• This product has a polarized plug (one blade is wider than
the other) as a feature to reduce the risk of electric shock.
This plug will t in a polarized outlet only one way. If the
plug does not t fully in the outlet, reverse the plug. If the
plug still does not t, contact a qualied electrician.
• Do not use an extension cord unless the plug can be fully
inserted. Do not alter or replace the plug.
• This product employs overload protection (fuse). A blown
fuse indicates an overload or a short-circuit condition. If
the fuse blows, unplug the product from the outlet. Also
Safety Information
AB-3 CE unplug any additional string or products that may be
attached to the product. Replace the fuse as per the user
servicing instructions (follow product markings for proper
fuse rating) and check the product. If replacement fuse
blows, a short-circuit may be present and the product
should be discarded.
• Read and follow all instructions that are on the product or
provided with the product.
SAVE THESE
INSTRUCTIONS
USE AND CARE
INSTRUCTION
1. When the product is placed on a live tree, the tree should
be well maintained and fresh. Do not place on live trees
in which the needles are brown or break off easily. Keep
the tree holder lled with water.
2. If the product is placed on a tree, the tree should be well
secured and stable.
3. Before using and reusing, inspect the product carefully.
Discard any products that have cut, damaged or frayed
wire insulation cords, cracks, lamp holders or enclosures,
loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product
from wherever it is placed, including trees, branches,
or bushes, to avoid any undue strain or stress on the
product conductors, connections and wires.
5. When not in use, store neatly in a cool, dry location
protected from sunlight.
To reduce the risk of re and electric shock:
1. Do not install on trees having needles, leaves or branch
coverings of metal or materials which look like metal and.
2. Do not mount or support wires in a manner that can cut
or damage wire insulation.
CAUTION: Do not attempt to inflate this unit
during unusually strong winds. If it becomes too windy for
safe operation, allow the unit to deate and wait for safer
conditions.
CAUTION: Do not connect to another lighting
string, decorative outfit, or seasonal product. To reduce
the risk of fire do not deliberately reposition either lamp
holder contact.
Do not attempt to inate your AirblownTM Inatable during
unusually strong winds. If it becomes too windy for safe
operation, simply allow your AirblownTM Inflatable to de-
ate and wait for better conditions before re-inating.
Protect the electric fan and power cord from direct expo-
sure to water. This precaution will reduce the risk of elec-
trical shock. When the temperature is below 14° F (-10°
C), the motor may temporarily stop running. The motor will
begin functioning again higher temperatures.
WARNING
Remove all plastic fasteners and tags. These are part of
the packaging and should be discarded.
This item is not a toy and should be used for decorative
purposes only.
For indoor and outdoor use.
120 V 60 Hz.
CAUTION
1. For temporary (90 days max) installation and use only.
2. Replace only with same type 7 Watt Max C7 cande-
labra (E12) base lamp.
3. To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
4. To reduce the likelihood of excessive heat and possible
damage, use only decorative lamp accessories pac-
kaged with this product or marked for use with this pro-
duct.
5. Disconnect power before replacing the fuse or the lamp.
6. To reduce the risk of re, do not reposition either lam-
pholder contact.
7. Do not place near standing areas of water, such as
ponds and pools.
WARNING: READ AND
UNDERSTAND ALL
INSTRUCTIONS.
Failure to follow all instructions listed below, may result in
electric shock, re and/or serious personal injury.
WARNING:
ELECTRIC PRODUCT. Keep away from children. As with
all electrical products, precautions should be observed du-
ring handling and use to reduce the risk of electric shock. If
the supply cord is damaged, it must be replaced by the ma-
nufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. To avoid the risk of electrical
shock, always make sure the figure is unplugged from the
electrical outlet before assembling, disassembling, or relo-
cating.
This product is to be assembled by adults only.
TM
FREQUENTLY ASKED
QUESTIONS (FAQ’s)
1. Can I continually run my AirblownTM Inatable?
Yes, you can run your AirblownTM Inatable during
the day and at night. We recommend that you turn
off your Animated AirblownTM Inatable when leaving
the immediate area and when retiring for the evening.
Otherwise, your AirblownTM Inatable is designed to run
continually as you see t.
2. What happens if my AirblownTM Inatable becomes
torn?
Rips in the AirblownTM In ata b le can be s ewn by hand (n o
special thread is required) or taped with clear packing
tape.
3. How can I clean my AirblownTM Inatable?
Wipe clean with a damp cloth and allow to dry before
storing away. Use mild detergent if necessary.
4. When I unplug my AirblownTM Inatable, it deates.
Why is this?
Your AirblownTM Inatable will not stay inated unless it
is plugged in and the fan is blowing air.
5. How much electricity does an AirblownTM Inatable
consume?
It uses about as much energy as a standard string of
holiday lights.
USER SERVICING
INSTRUCTIONS
Lamp Replacement (Not included)
Disconnect the plug from the electrical outlet and allow
the lamp to cool completely before replacing bulb. Do not
touch the bulb when the power is "ON" as it is extremely
hot and make cause electrocution.
1. Grasp plug and remove from receptacle or other outlet
device.Do not unplug by pulling on the cord.
2. Open the zipper opening on the AirblownTM Inatable.
3. Push aside the locking tabs to open the light cover.
4. Replace lamp with same type 7W maximum, cande
labra base, UL classied.
5. Do not over-tighten the lamp as this may damage the
lamp or lamp holder.
Replace only with same type C7, 7 Watt Max Cande-
labra-base 120 Volt UL Classied lamps.
Fuse Replacement
WARNING: Risk of Fire:
Replace only with same size and type
of fuse. Do not replace the attachment
plug. Contains a safety device (fuse)
that should not be removed. Discard
product if attachment plug is damaged.
1. Grasp plug and remove from the
receptacle or other outlet device. Do
not unplug by pulling on the cord.
2. Open fuse cover. Slide open the fuse
access cover on top of the attachment
plug towards blades. (See illustration)
3. Remove fuse carefully.
4. Replace fuse only with 5 Amp Max, 125 Volt (provided
with product).
5. Close the fuse cover. Slide closed the fuse access cover
on top of the attachment plug.
These Instructions Are For These Items
35008 35097 35741 35799
35925 35935 35940 35999
36060 36239 37464 37467
37481 37729 37730 37746
37748 37749 37788 37963
38169 38173 38177 38195
38200 38202 38214 38426
38463 38471 38479 38519
38536 38598 38780 38788
39541 55991 56315 56560
56684 56685 56729 59266
59874 64903 64903 70230
72709 74265 75325 82358
88629 88728 88775 88814
89028 110408 110408 110505
110 7 3 3 11118 2 111217 113 4 01
224398 223561 224155 116909
116449 116954 116955 116960
113 9 0 6 1159 63
TROUBLE SHOOTING
CHECKLIST
If your AirblownTM Inatable is not inating, the problem may
be.
1. The power source is disabled or the cord may be
unplugged.
2. Debris may be lodged in the motor.
3. The zipper may not be securely fastened, sealing the
Animated AirblownTM Inatable.
4. The temperature may be below 14° F (-10° C).
NOTE: ONCE FAN IS UNPLUGGED AND STOPS
BLOWING, YOUR AirblownTM Inatable WILL DEFLATE.
6. What is the best way to store my AirblownTM
Inatable?
Store in a bag, box or other storage container and keep in
a cool, dry location.
7. I have stored my AirblownTM Inatable for several
months and now the motor does not work?
Sometimes the air intake may be blocked by loose
grass/leaves or other particles. Gently shake, knock or
tap the motor and see if it will operate again.
Assembly Instructions
x1 x6 x4 x4 x1
Package Contents
Ensure the four clips on the bottom
of the fabric of the inatable (A) are
attached to the plastic legs on the
base of the intlatable.
Ensure that the air intake on the
inatable (A) unit is clear of fabric and
other obstructions and that the zipper
is fully closed. Some inatables have
more than one zipper.
Turn the inatable (A) upright and insert
four base stakes (B) through the holes
of the plastic legs into the ground.
Plug in the inatable (A) into an outlet
or other power source to inate.
Once fully inated, clip the nylon tethers
(C) to each of the attached nylon loops
on the side of the inatable (A).
Drive the stakes (D) into ground at a
45-degree angle.
AB
1
For maximum stability bring tether down
to a 45-degree angle from the inatable
as shown in the illustration. In order to
achieve this you may need to wrap the
excess tether around the top of the stake.
23
4 5
78
A
A
A
A
B
C
A
D
45°
DE
C
Visit
WWW.GEMMY.COM
for more information.
©2019 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 (800) 274-6717
MADE IN CHINA / PRINTED IN CHINA
Using the loop at the end of the tether
(C), fasten the tehters to the tether
stakes(D).
6
D
C
Do’s and Don’ts
1. Do check your inatable daily and adjust
to stand up straight.
2. Do not attempt to operate your inatable
in unusually strong winds.(see caution)
3. Do not unplug by pulling on cord.
For faster deation, unzip zipper after
unplugging plug.
Do
Don’t
9
CAUTION:
1.) For temporary (90 days max) installation and use only. 2.) This is an
electric product — not a toy! To avoid risk of fire, burns, personal injury
and electric shock it should not be played with or placed where small
children can reach i t. 3.) Use only 125-volt fuse, 5 a mp. max. 4.)
Replace only with same type 7 W att M ax C7 candelabra (E12) base
lamp. 5.) To prevent electric shock, match wide blade of plug to wide
slot, f ully i nsert. 6.) To reduce the likelihood o f excessive heat and
possible damage, use only decorative lamp accessories packaged with
this product or marked for use with this product. 7.) Disconnect power
before replacing the fuse or the lamp. 8.) To reduce the risk of fire, do
not reposition either lampholder contact. 9) Do not place near standing
areas of water, such as ponds and pools.
This manual suits for next models
72
Other Gemmy Toy manuals
