Geneko GWR-I252 User manual

QUICK START
GWR-I Industrial 2G/3G Router
GUIDE
GWR-I202, GWR-I252, GWR-I352

WHAT’S IN THE BOX:
1. Geneko GWR-I router
2. Ethernet cable
3. Antenna GSM/GPRS/EDGE/UMTS/HSPA+
(850/900/1800/1900/2100 MHz), 1 or 2 pieces
4. DIN rail kit
5. RS-232 console cable (optional accessory)
6. GSM antenna extension cord(s) with magnetic base
(optional accessory)

PORTS & CONNECTORS
Front panel
Top panel
AUXILIARY MODEM
ANTENNA
GND
STATUS LED
RS-232 / RS-485
CONSOLE PORT 1
RS-232 / RS-485
CONSOLE PORT 2
ETHERNET PORT
2 SIM SLOTS
ON PCB
DIGITAL INPUT
DIGITAL OUTPUT
POWER PORT
RESET BUTTON
MAIN ANTENNA
3

4
INSERTING SIM CARDS
Warning: do not insert or eject SIM cards while router is
powered on. Make sure that power connector is disconn-
ected from device before inserting or ejecting SIM cards.
* Use the screwdriver PH1 type to disassemble the right part of the router
casing
* Unlock and lift the SIM card 1 holder, and put SIM card 1 in it
* Lock the SIM card 1 holder
* Repeat these steps for second SIM card, if necessary
* Put the casing back and use the screwdriver to tighten the screws
12 3

CONNECTING ROUTER
Warning: Check that the power connector is wired according
to the instructions for connecting power supply.
* Connect GSM antennas to the router. Make sure that antennas are well
tightened (however, don't use too much force in order not to damage
antenna connector on the router).
* Plug power connector into power port on the router. Green power
indicator will turn on
* Wait approximately 45 seconds for the router to become fully operational
* Plug one side of Ethernet cable to Ethernet port on the router
* Plug the other side of Ethernet cable to Ethernet port on the computer.
1
2
3
5

6
ADMINISTRATION WEB PAGE
* Add network 192.168.1.0/24 to the interface on the PC
* Optional: Ping 192.168.1.1 to check if the router is accessible
* Open the Web browser (e.g. Firefox, Chrome, Safari, Opera, or Internet
Explorer) and enter the following address: http://192.168.1.1
* When prompted for your login credentials, use "admin" (without
quotation marks) for both username and password.
* After logging in you should be able to see administration web page,
which allows you to easily set up the router.

7
QUICK SETUP
* Once logged in to administration web page, click on SETTINGS ->
MOBILE SETTINGS link from the menu on the left side of the screen.
* Your GSM operator should provide you with PROVIDER, USERNAME
(optional), PASSWORD (optional), APN and PIN (optional) information.
* If SIM card is present, enter this into corresponding fields, and then click
on SAVE button. Otherwise, you need to insert SIM card as explained in
"Inserting SIM cards" chapter.
* After a few minutes when your GWR router is connected, connection
status will be accomplished.
* Click on SETTINGS -> ETHERNET SETTINGS -> LAN PORTS link from the
menu on the left side of the screen
* Set IP Address and Subnet Mask and click on SAVE button
* Add a new network to the interface on the PC
* Ping new IP address
* When the GWR router is accessible, insert new IP address in a Web browser
* Click on MAINTENANCE -> DATE/TIME SETTINGS link from the menu on the
left side of the screen.
* Click on SYNC CLOCK button. GWR Router will sync DATE and TIME fields
with your computer's current date and time. Now click on SAVE button.

When troubleshooting router, make sure logs are
turned on. When submitting support request, logs
should be included.
.
TURN LOGGING ON
Register on web site for support.
Official web site: https://www.geneko.rs
GENEKO is the registered trademark of GENEKO Company.
© 2018 GENEKO Co. All rights reserved.
QSG GWR-I202-352 Rev. A Apr 18
* Click on MANAGEMENT -> LOGS link from the menu on the left side of
the screen.
* Click on LOCAL SYSLOG radio button, and then click on SAVE button.
* Set appropriate log size and click on SAVE button.
* Log is now available for download. It will be downloaded to your
computer when you click on EXPORT LOG button.