Geneko GWR252 User manual

QUICK START
GWR 2G/3G Routers
GUIDE
GWR352 WV, GWR202/252/352

WHAT’S IN THE BOX:
1. Geneko GWR router
2. AC/DC adapter
3. Ethernet cable
4. RS-232 console cable
5. Antennas GSM/GPRS/EDGE/UMTS/HSPA+
(850/900/1800/1900/2100 MHz), 1 or 2 pieces
6. DIN rail kit (optional accessory)
7. GSM antenna extension cord(s) with magnetic base
(optional accessory)

AUXILIARY
MODEM
ANTENNA
MAIN
ANTENNA
SIM CARD 1
HOLDER
SIM CARD 1
HOLDER
EJECT BUTTON
SIM CARD 2
HOLDER
SIM CARD 2
HOLDER
EJECT BUTTON
ETHERNET
PORT
RS-232
CONSOLE
PORT
USB
PORT
RESET
BUTTON
POWER
PORT
PORTS & CONNECTORS
GWR202/252/352 models
Front Panel
Rear Panel
AUXILIARY
MODEM
ANTENNA
MAIN
ANTENNA
SIM CARDS HOLDER COVER
ETHERNET
PORT
RS-232
CONSOLE
PORT
USB
PORT
RESET
BUTTON
POWER
PORT
GWR352 WV model
Front Panel
Rear Panel
3

4
INSERTING SIM CARDS
Warning: do not insert or eject SIM cards while the router
is powered on. Make sure to disconnect router from
AC/DC adapter before inserting or ejecting SIM cards.
* Push SIM card 1 holder eject button until SIM card 1 holder is slightly
protruded from back panel.
* With the GWR352 WV model, unlike other models, it is necessary to
disassemble the cover of SIM card holders first using a screwdriver
PH1 type.
* Pull out SIM card 1 holder and place SIM card in it.
* Put SIM card 1 holder back to its slot.
* With the GWR352 WV model tighten the screw on cover of SIM card
holders using the screwdriver.
* Repeat these steps for second SIM card, if necessary.
12 3

CONNECTING ROUTER
Warning: Use only the router’s box power supply.
* Connect GSM antennas to the router. Make sure that antennas are well
tightened (however, don't use too much force in order not to damage
antenna connector on the router).
* Plug AC/DC adapter cable into power port on the router. Green power
indicator will turn on.
* Wait approximately 45 seconds for the router to become fully
operational.
* Plug one side of Ethernet cable to Ethernet port on the router.
* Plug the other side of Ethernet cable to Ethernet port on your
computer.
123
5

6
ADMINISTRATION WEB PAGE
* Add network 192.168.1.0/24 to the interface on the PC
* Optional: Ping 192.168.1.1 to check if the router is accessible
* Open the Web browser (e.g. Firefox, Chrome, Safari, Opera, or Internet
Explorer) and enter the following address: http://192.168.1.1
* When prompted for your login credentials, use "admin" (without
quotation marks) for both username and password.
* After logging in you should be able to see administration web page,
which allows you to easily set up the router.

7
QUICK SETUP
* Once logged in to administration web page, click on SETTINGS ->
MOBILE SETTINGS link from the menu on the left side of the screen.
* Your GSM operator should provide you with PROVIDER, USERNAME
(optional), PASSWORD (optional), APN and PIN (optional) information.
* If SIM card is present, enter this into corresponding fields, and then click
on SAVE button. Otherwise, you need to insert SIM card as explained in
"Inserting SIM cards" chapter.
* After a few minutes when your GWR router is connected, connection
status will be accomplished.
* Click on SETTINGS -> ETHERNET SETTINGS -> LAN PORTS link from the
menu on the left side of the screen
* Set IP Address and Subnet Mask and click on SAVE button
* Add a new network to the interface on the PC
* Ping new IP address
* When the GWR router is accessible, insert new IP address in a Web browser
* Click on MAINTENANCE -> DATE/TIME SETTINGS link from the menu on
the left side of the screen.
* Click on SYNC CLOCK button. GWR Router will sync DATE and TIME fields
with your computer's current date and time. Now click on SAVE button.

When troubleshooting router, make sure logs are
turned on. When submitting support request, logs
should be included.
.
TURN LOGGING ON
Register on web site for support.
Official web site: https://www.geneko.rs
GENEKO is the registered trademark of GENEKO Company.
© 2018 GENEKO Co. All rights reserved.
QSG GWR352/352WV Rev. A Apr 18
* Click on MANAGEMENT -> LOGS link from the menu on the left side
of the screen.
* Click on LOCAL SYSLOG radio button, and then click on SAVE button.
* Set appropriate log size and click on SAVE button.
* Log is now available for download. It will be downloaded to your
computer when you click on EXPORT LOG button.