General International 10-800CF M1 Parts list manual

FEATURES
Simple design for easy set-up and mainte-
nance.
Efficient collection and separation of large
chips which drop into the collector drum
before reaching the impeller.
High quality motor designed specifically
for heavy duty use and long service life.
Remote control for convenient operation
from virtually anywhere in the shop.
1-15 hours Pre-programmed timer run set-
tings in 1 hour increments.
Equipped with an ultra efficient 1 micron
canister filter with total surface area of 48.4
square feet.
Canister filter equipped with crank han-
dle/internal shaker for easy filter cleaning
without removing bag.
Sturdy steel support frame and collection
drum both equipped with casters for com-
plete mobility within the shop.
30 gallon chip collection drum included.
SPECIFICATIONS
AIRFLOW CAPACITY
611 CFM
BLOWER WHEEL DIAMETER
13”(330 MM)
SOUND RATING
80 DB
INLET DIAMETER
(1) 5”(127 MM)
OR (2) 4”(102 MM)
STATIC PRESSURE
10”OF WATER
CANISTER FILTER (DIA X H)
15 3⁄4”X 19 3⁄4”(400 X 502 MM)
OVERALL DIMENSIONS (L X W X H)
52 3⁄4”X 32”X 70”
(1340 X 810 X 1780 MM)
MOTOR
1 1⁄2 HP, 110 V, 12 A
WEIGHT
198 LBS (90 kg)
SETUP & OPERATION MANUAL
REVISION 1 - JUNE 04/10
© Copyright General® International 06/2010
MODEL
10-800CF M1
PORTABLE 2 STAGE DUST COLLECTOR
– 1 1/2 HP

THANK YOU for choosing this General®International model 10-800CF M1
1 1/2 HP Portable 2 Stage Dust Collector. This dust collector has been carefully tested and
inspected before shipment and if properly used and maintained, will provide you with years
of reliable service. For your safety,as well as to ensure optimum performance and trouble-free
operation, and to get the most from your investment, please take the time to read this manu-
al before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation,basic function, and features
of this dust collector as well as the set-up,maintenance and identification of its parts and com-
ponents. This manual is not intended as a substitute for formal woodworking instruction, nor to
offer the user instruction in the craft of woodworking. If you are not sure about the safety of
performing a certain operation or procedure, do not proceed until you can confirm, from
knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.
Disclaimer: The information and specifications in this
manual pertain to the unit as it was supplied from the
factory at the time of printing. Because we are commit-
ted to making constant improvements, General®
International reserves the right to make changes to
components, parts or features of this unit as deemed
necessary,without prior notice and without obligation to
install any such changes on previously delivered units.
Reasonable care is taken at the factory to ensure that
the specifications and information in this manual corres-
ponds with that of the unit with which it was supplied.
However, special orders and “after factory” modifica-
tions may render some or all information in this manual
inapplicable to your machine. Further, as several gene-
rations of this model of dust collector and several ver-
sions of this manual may be in circulation,if you own an
earlier or later version of this unit, this manual may not
depict your machine exactly. If you have any doubts or
questions contact your retailer or our support line with
the model and serial number of your unit for clarifica-
tion.
GENERAL® INTERNATIONAL
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone [phone] • Fax [phone] • www.general.ca

GENERAL®& GENERAL®INTERNATIONAL WARRANTY
All component parts of General®, General® International and Excalibur by General
International ® products are carefully inspected during all stages of production and each unit
is thoroughly inspected upon completion of assembly.
Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General® and General®
International agree to repair or replace any part or component which upon examination,
proves to be defective in either workmanship or material to the original purchaser for the life
of the tool.
However, the Limited Lifetime Warranty does not cover any product used for pro-
fessional or commercial production purposes nor for industrial or educational applications.
Such cases are covered by our Standard 2-year Limited Warranty only. The Limited Lifetime
Warranty is also subject to the “Conditions and Exceptions”as listed below.
Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial,
industrial and educational applications are warranted for a period of 2 years (24 months) from
the date of purchase. General® and General® International agree to repair or replace any
part or component which upon examination,proves to be defective in either workmanship or
material to the original purchaser during this 2-year warranty period,subject to the“conditions
and exceptions”as listed below.
To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime
Warranty, all defective parts, components or machinery must be returned freight or postage
prepaid to General® International, or to a nearby distributor, repair center or other location
designated by General® International. For further details call our service department at 1-888-
949-1161 or your local distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof
of purchase and a“letter of claim”must be included (a warranty claim form can also be used
and can be obtained,upon request,from General® International or an authorized distributor)
clearly stating the model and serial number of the unit (if applicable) and including an expla-
nation of the complaint or presumed defect in material or workmanship.
CONDITIONS AND EXCEPTIONS:
This coverage is extended to the original purchaser only. Prior warranty registration is not
required but documented proof of purchase i.e. a copy of original sales invoice or receipt
showing the date and location of the purchase as well as the purchase price paid, must be
provided at the time of claim.
Warranty does not include failures,breakage or defects deemed after inspection by General®
or General® International to have been directly or indirectly caused by or resulting from;
improper use, or lack of or improper maintenance, misuse or abuse, negligence, accidents,
damage in handling or transport, or normal wear and tear of any generally considered con-
sumable parts or components.
Repairs made without the written consent of General® International l will void all warranty.

TABLE OF CONTENTS
Rules for safe operation . . . . . . . . . . . . . . .5
Additional safety instructions - specific to
this dust collector . . . . . . . . . . . . . . . . . . .6
Electrical requirements . . . . . . . . . . . . . . .7
Grounding instructions . . . . . . . . . . . . . . . . . . . . . . .7
Circuit capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Extension cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Identification of main parts and
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Unpacking and preparation for set-up &
assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
List of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Additional requirements for set up . . . . . . . . . . . . .9
Shop placement / Space considerations . . .10
Layout out a plan for the piping . . . . . . . . . . . . .10
Assembly instructions . . . . . . . . . . . . .11-16
Operating Instructions . . . . . . . . . . . . .17-18
Connecting to a power source . . . . . . . . . . . . . . .17
Operating the control panel . . . . . . . . . . . . . . . . . .17
Circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Operating the remote control . . . . . . . . . . . . . . . . .18
Seal air leaks (if needed) . . . . . . . . . . . . . . . . . . . .18
Before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Maintenance & Servicing . . . . . . . . . . .19-20
Cleaning or replacing the canister filter . . . . . . . . . . . .19
Emptying the collector bag & drum . . . . . . . . . . .20
Recommended optional accessories . . . . .20
Parts list & diagrams . . . . . . . . . . . . . .21-23
Wiring diagram . . . . . . . . . . . . . . . . . . . .24

RULES FOR SAFE OPERATION
To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as poten-
tial hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that
may result from improper use of its equipment.
1. Do not operate the dust collector when tired, distract
ed, or under the effects of drugs, alcohol or any me-
dication that impairs reflexes or alertness.
2. The working area should be well lit, clean and free of
debris.
3. Keep children and visitors at a safe distance when the
dust collector is in operation; do not permit them to
operate the dust collector.
4. Childproof and tamper proof your shop and all
machinery with locks, master electrical switches and
switch keys, to prevent unauthorized or unsupervised
use.
5. Stay alert! Give your work your undivided attention.
Even a momentary distraction can lead to serious
injury.
6. Fine particulate dust is a carcinogen that can be haz-
ardous to health. Work in a well-ventilated area and
wear face, eye, ear, respiratory and body protection
devices.
7. Do not wear loose clothing, gloves, bracelets, neck-
laces or other jewelry while the dust collector is in
operation. Wear protective hair covering to contain
long hair and wear non-slip footwear.
8. Do not insert hands, fingers or any foreign objects into
ventilation inlet and outlet openings.
9. Do not operate this machine without a canister filter
properly installed on the unit.
10. Clean filter on a regular basis and replace as needed.
11. Do not handle the electrical plug with wet hands.
12. Do not use this unit outdoors, on or near wet surfaces.
13. Always turn on the dust collector before starting the
dust producing machine. Always turn off the dust pro-
ducing machine before turning off the dust collector.
14. Do not vacuum anything that is burning, smoking or
smoldering such as cigarettes, matches or hot ashes.
15. Do not vacuum or use this dust collector near flamma-
ble or combustible liquids, gases, gasoline or other
fuels, lighter fluid,cleaners,oil or solvent based paints,
natural gas, hydrogen or explosive dusts like coal
dust, magnesium dust, grain dust or gun powder.
16. Do not operate the unit until a dust hose is installed
onto the hose inlet.
17. Never leave the machine unattended while it is run-
ning or with the power on.
18. To avoid health hazards from vapors or dusts, do not
vacuum toxic material.
19. Use only recommended accessories. Use of acces-
sories NOT recommended by GENERAL® INTERNATIO-
NAL may result in a risk of injury or damage to the
machine.
20. Always disconnect the unit from the power source
before servicing, performing any maintenance or
repairs and when changing bags or hoses, or if the
machine will be left unattended.
21. Make sure that the switch is in the“OFF”position before
plugging in the power cord.
22. Make sure the tool is properly grounded. If equipped
with a 3-prong plug, it should be used with a three-
pole receptacle. Never remove the third prong.
23. Do not use this dust collector for any purpose other
than its intended use. If used for other purposes, GE-
NERAL® INTERNATIONAL disclaims any real or implied
warranty and holds itself harmless for any injury, which
may result from that use.
5