General International 10-810 Installation and operation manual

FEATURES
•Excellent for collecting the large chips which will drop into
the garbage can before reaching the impeller.
•The filter bag filters out the remaining sawdust down to
5 microns.
•With the cyclone effect fitting onto a standard garbage can
there is no longer a need to dump the chips and dust from
the collection bag to a disposable bag.
•Simply set the garbage can on the curb with the lid to be
emptied.
•5 micron filter bag as standard accessory.
•45 gallon (55 gallon U.S.) drums not included.
•Overall height 121
1⁄4
”(3080 mm).
• Mobile base for garbage can included.
AIR SPEED
AIR DELIVERY
AIR FLOW CAPACITY
AIR SUCTION
FILTER BAG
SPACE OCCUPIED
PACKING SIZE
MOTOR
NET WEIGHT
GROSS WEIGHT
41 M/SEC
80 M3/MIN
2800 CFM
8" ( 203 mm) x 1 hole
Ø24” x 70 7/8” (Ø610 x 1800 mm)
64” x 55” x 110 1/4” (1630 x 1400 x 2800 mm)
51” x 34 1/4” x 28 3/8” (1300 x 870 x 720 mm)
3 HP
550 LBS (250 Kg)
616 LBS (280 Kg)
SPECIFICATIONS

"WARNING” When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock
and personal injury, including the following.
1. KEEP WORK AREA CLEAR
2. CONSIDER WORK AREA ENVIRONMENT
-Do not expose tools to rain
-Do not use tools in damp or wet locations
-Keep work area well lit
-Do not use tools in the presence of flammable liquids or gases
3. GUARD AGAINST ELECTRIC SHOCK
-Avoid body contact with earthed or grounded surfaces
4. KEEP OTHER PERSONS AWAY
-Do not let persons especially children, not involved in the
work touch the tool or the extension cord and keep them
away from the work area
5. STORE IDLE TOOLS
- When not in use, tools should be stored in a dry locked-up
place, out of reach of children
6. DO NOT FORCE THE TOOL
-It will do the job better and safer at the rate for which it
was intended
7. USE THE RIGHT TOOL
-Do not force small tools to do the job of a heavy duty tool
-Do not use tools for purposes not intended for example do
not use circular saws to cut tree limbs or logs
8. DO NOT ABUSE THE CORD
-Never yank the cord to disconnect it from the socked.
Keep the cord away from heat, oil and sharp edges
9. SECURE WORK
-Where possible use clamps or a vice to hold the work. It is
safer than using your hand
10. DO NOT OVERREACH
-Keep proper footing and balance at all times
11. MAINTAIN TOOLS WITH CARE
-Keep cutting tools sharp and clean for better and safer
performance
-Follow instructions for lubricating and changing accessories
-Inspect tool cords periodically and if damaged have
them repaired by an authorized service facility
-Inspect extension cords periodically and replace if damaged
-Keep handles dry, clean and free from oil and grease
12. DISCONNECT TOOLS
-When not in use,before servicing and when changing acces-
sories such as blades,bits and cutters,disconnect tools from the
power supply
13. AVOID UNINTENTIONAL STARTING
-Ensure switch is in "off" position when plugging in
14. USE OUTDOOR EXTENSION LEADS
-When the tool is used outdoors, use only extension cords
intended for outdoor use and so marked
15. STAY ALERT
-Watch what you are joining,use common sense and do not
operate the tool when you are tired
16. CHECK DAMAGED PARTS
-Before further use of tool, it should be carefully checked to
determine that it will operate properly and perform its
intended function
- Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other condi-
tions that may affect its operation
- A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center
unless otherwise indicated in this instruction manual
- Have defective switches replaced by an authorized service center.
-Do not use the tool if the switch does not turn it on and off
17. -The use of any accessory or attachment other than one
recommended in this instruction manual may present a
risk of personal injury.
18. HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON
-This electric tool complies with the relevant safety rules.
Repairs should only be carried out by qualified persons by
using original spare parts, otherwise this may result in
considerable danger to the user.
Woodworking can be dangerous if safe and proper operating procedures are not
followed. As with all machinery, there are certain hazards involved with the
operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety
precautions are overlooked or ignored, personal injury to the operator may result.
Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury.
But even the best guard Will not make up for poor judgment, carelessness or
inattention. Always use common sense and exercise caution in the workshop. If a
procedure feels dangerous, don’t try it. Figure out an alternative procedure that
feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. GENERAL INTERNATIONAL
strongly recommends that this machine not be modified and/or used for any
application other than that for which it was designed. If you have any questions
relative to a particular application, DO NOT use the machine until you have first
contacted GENERAL INTERNATIONAL to determine if it can or should be performed
on the product.
1. READ and understand instruction literature before operating product.
2. FOLLOW all local electrical and safety codes, as well as some relevant CSA
standards. All electrical connections and wiring should be performed by
qualified personnel only.
3. TO AVOID electrical shock, do not expose to rain or use in damp locations.
Store machine indoors. Use for dry pick-up only.
4. UNPLUG machine from power source before servicing, unclogging or
cleaning unit.
5. DUST generated by certain woods and wood products can be hazardous to
your health. always wear eye protection and use face or dust mask in
dust-laden environments.
6. REPLACE or repair damaged or worn cord immediately.
7. PROTECT the power cable and never allow the cable to come in contact with
sharp objects.
8. DO NOT kink power cable and never allow the cable to come in contact with
oil, grease, hot surfaces or chemicals.
9. MAKE CERTAIN that the power source conforms to the requirements of your
equipment.
10.THERE is a high speed blower fan inside the blower housing that can
amputate fingers, grab loose clothes or neckties. DO NOT insert fingers or any
foreign object into the blower housing.
All component parts of GENERAL INTERNATIONAL machinery are carefully inspected during all production stages and each
machine is thoroughly inspected upon completion of assembly. Because of quality, GENERAL INTERNATIONAL agrees to
repair or replace any genuine part or parts which, upon examination, proves to be defective in workmanship or material
within a period of 24 months from date of purchase.In order to obtain warrantee, all defective parts must be returned pre-
paid to GENERAL INTERNATIONAL MFG. Co Ltd. Repairs made without our written authorization voids all guarantees.
GENERAL ® INTERNATIONAL guarantee
SSAAFFEETTYYRRUULLEESS
READ CAREFULLY BEFORE OPERATING THE MACHINE

2
UNPACKING AND ASSEMBLY
1. Unpack the shipping container with care.
2. Check nothing missing for the component listed in the assembly drawing.
3. Assembly the dust collector by following the drawing of the assembly draw.
4. Contact local agent for any problem of assembly and missing part.
Warning! Do not connect the dust collector to the power source until machine is completely assembled and you have read
and understand the entire instruction manual.
HANDLING AND TRANSPORTATION
The net weight of this machine is about 550 LBS (250 kg).We recommend to move and assemble it with forklift truck.
ELECTRICAL CONNECTION / DISCONNECTION
1. ELECTRICAL CONNECTION
A - The hand-operated power disconnection device or the plug is recommended to be provided before the
connection of power supply.
B - For the protection of control device, we recommend the operator to use 20 Amp time lag fuse, if an
extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and
matching receptacle which will accept the machine’s plug.
2. ELECTRICAL DISCONNECTION
A - The disconnection is carried out by hand-operated disconnecting device.
B - Be sure to disconnect this machine from power source, when you want to stop the job, maintenance, and
adjustment.
3. GROUNDING
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
•••••••••••••••••••••••• WARNING! ••••••••••••••••••••••••
DO NOT DISCONNECT GROUNDING TERMINAL BEFORE DISCONNECTING POWER SOURCE.
GENERAL® INTERNATIONAL 2-Stage Dust Collectors are carefully tested and inspected
before shipment and if properly used will give perfect results. However, a reasonable
amount of care and attention is necessary to ensure perfect performance and accurate
work. It is imperative that you take a few moments to familiarise yourself with these instruc-
tions, as they will no doubt save you a lot of time and trouble.
2 STAGE DUST COLLECTOR
10-810

OPERATIONS
Note: This dust collector may produce a slight odor for the first couple hours of operation due to the protective coating
which is applied to internal components. This odor will dissipate and should be disregarded.
This dust collector is designed to help maintain clean, safe conditions around dust creating machine in work shop
and factory. Dust collector work by moving larger volume of air at lower suction pressure than vacuum cleaner.
These unit is not designed to be used as high suction vacuum cleaners.
DO NOT OPERATE WITHOUT THE DISCHARGE GUARD AND DUST BAG IN POSITION.
ASSEMBLY DRAWING & INSTRUCTIONS
Remove the dust collector components from the shipping containers. Please check parts list for missing or
damaged parts.
3
•••••••••••••••••••••••• WARNING! •••••••••••••••••••••••
THE BLOWER HOUSING CONTAINS A HIGH SPEED RADIAL FAN THAT CAN AMPUTATE FINGERS,
GRAB LOOSE CLOTHING AND NECKTIES, OR PROPEL DUST AT HIGH VELOCITY.
1
2
3
4
5
6
7
8
10
9
11
12
13
14
15
17
16
1. DRUM
2. CYCLONE SEPARATOR
3. 7" FLEXIBLE HOSE
4. HARDWARE PACKAGE
5. Ø 61 CM BAG BAND
6. MOTOR BASE
7. COVER
8. UPPER LEG
9. DRUM BASE
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
4 pieces
2 pieces
10. Ø 4" X 4 INLET
11. Ø 8" OUTLET
12. AIR FLOW PIPE
13. BLOWER HOUSING
14. SUPPORT BRACKET
15. 5 MICRON FILTER BAG
16. BAG HANGER
17. LOWER LEG
1 piece
1 piece
1 piece
1 piece
4 pieces
1 piece
1 piece
4 pieces

1. Fasten the motor base to motor
with four 3/8" x 1 inch-long screws,
four 3/8" flat washers,and four 3/8"
nuts.
2. Fasten air flow pipe to blower
housing with four 3/8" flat washer
and four 3/8" x 1 inch-long screws.
3. Remove the paper backing and
start the gasket material around
the outer edge of drum and con-
tinue until a complete circle.
7. Assemble one leg section to blow-
er housing and fasten with four 3/8" x 1
inch-long screw, four flat washers.
NOTE: Do not completely tighten hardware
at this time.
8. Assemble remaining three legs to
blower housing in the same manner.
9. Illustrates upper legs assembled to
blower housing. 10. Place one support bracket on the inside of two upper legs.
Do not use any screw at this time.
4
4. Fasten drum to blower housing
with ten 3/8" flat washer and ten
3/8" screws.
IMPORTANT: drum can be rotated to any
position best suited for the inlet, however,
please do not position drum so inlet will
interfere with four leg mounting lugs.
5. Remove the paper backing and
start the gasket material around
the outer edge of drum and con-
tinue until a complete circle.
6. Fasten the cyclone separator with
drum in ten 3/8" screws,twenty 3/8"
flat washer and ten 3/8" hex nuts.
Flat washer should be used on two
side of flange.

11. Place another support bracket on
the inside of two legs. 12. Place one lower leg to the outside of upper leg and support bracket. 13. Make sure the lower leg on the outside of upper leg and support
bracket on the inside of upper leg.
Fasten upper leg, lower leg and
support bracket with four 3/8" x
1 inch-long screws, eight 3/8" flat
washers and four 3/8" hex nut.
15. Remove the paper backing and
start the gasket material around
the outer edge of outlet and
continue until a complete turn.
16. Position outlet to the blower hou-
sing, and align holes. Fasten with
ten 3/8" x 1 inch-long screws and
ten 3/8" flat washer.
17. Position the 4 inch x 4 holes inlet
housing to 8 inch inlet of blower
housing. Align holes in inlet hou-
sing with pre-drilled holes in inlet
and fasten with three pan head
screws.
5
14. Attach the remaining brackets and
lower legs to upper legs assemblies
in the same manner.
LIFTING THE DUST COLLECTOR
THE DUST COLLECTOR CAN BE RAISED TECHNICALLY OR MANUALLY,
BUT WE STRONGLY RECOMMEND USING LIFT TRUCK WITH GUIDE
ROPES TO SET THE UNIT UPRIGHT.
IMPORTANT:Carefully loosen mounting hardware at least enough to
adjust the dust collector, mounting four legs to floor
surface. And then tighten all legs and foot mounting
hardware after dust collector is level with the floor
surface.
DO NOT ASSEMBLE CASTERS TO THE FEET AS THEY CAN CREATE HAZARD.

18. Position rubber gasket on the outer
edge of hole of collecting drum
cap and hose connector on the
rubber gasket.
19. Fasten hose connector to cover
with four 5/16 X 1" screw, four 5/16"
flat washer, four 5/16:" lock washer
and four 5/16" hex nut.
20. Assemble hose over bottom outlet
of cyclone separator and tighten
clamp.
21. Assemble hose over hose connec-
tor, slide clamp downward over
flange and tighten screw.
25. Place inlet of filter bag to 8" outlet
and tighten it with 8" bag band. 26. Assemble the wheel to collecting drum base with 3/8" hex nut and
3/8" flat washer.
27. Assemble remaining seven wheels
to 2 pieces of collecting drum base
in the same manner.
28. Position bag filter on 50 gallon
drum and tighten it with bag band
as shown.
6
22. Assemble switch panel on the
support bracket with two 3/8" x 3/4"
screws, four 3/8" flat washer and
two 3/8" hex nut.
23. Assemble bag hanger to blower
housing with two 3/8" x 3/4" screws,
and two 3/8" flat wahser.
24. Attach eyelet which on top filter
bag to hanger hook and lock it.

AASSSSEEMMBBLLYYDDRRAAWWIINNGG1100--881100
7

PARTS LIST
10-810
REF. N0.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
DESCRIPTION
5/16" x 3/4" HD HEX SCREW
5/16" FLAT WASHER
MOTOR BASE
5/16" HEX NUT
MOTOR
BLOWER COVER
BLOWER HOUSING
AIR FLOW PIPE
5/16" FLAT WASHER
5/16" x 3/4" HD HEX SCREW
GASKET TAPE
5/16" FLAT WASHER
5/16" x 3/4" HD HEX SCREW
DRUM
5/16" FLAT WASHER
5/16" HEX NUT
CYCLONE SEPARATOR
5/16" x 1" HD HEX SCREW
5/16" x 3/4" HD HEX SCREW
SWITCH PANEL
5/16" HEX NUT
5/16" FLAT WASHER
SUPPORT BRACKET( S )
SUPPORT BRACKET( L )
5/16" FLAT WASHER
5/16" x 1" HD HEX SCREW
UPPER LEG
5/16" HEX NUT
5/16" FLAT WASHER
3/8" x 3/4" HD HEX SCREW
Ø 8" OUTLET
QTY
4
8
1
4
1
1
1
1
4
4
3
9
9
1
18
9
1
9
2
1
2
4
2
2
16
16
4
16
10
10
1
REF. N0.
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
DESCRIPTION
LOWER LEG
5/16" FLAT WASHER
5/16" x 1" HD HEX SCREW
Ø 7" FLEXIBLE HOSE
Ø 7" HOSE CLAMP
5/16" x 3/4" HD HEX SCREW
5/16" FLAT WASHER
HOSE CONNECTOR
RUBBER GASKET
COVER
5/16" LOCK WASHER
5/16" HEX NUT
HOOK
BAG HANGER
5/16" FLAT WASHER
5/16" x 1" HD HEX SCREW
Ø 8" BAG BAND
FILTER BAG
Ø 61 CM BAG BAND
Ø 4" INLET
M4.2 PAN HEAD SCREW
3/8" HEX NUT
3/8" LOCK WASHER
BASE
WHEELS
5/16" x 3/4" HD HEX SCREW
5/16" HEX NUT
COVER PLATE
3/8" x 3/4" HD HEX SCREW
3/8" FLAT WASHER
3/8" HEX NUT
QTY
4
32
16
1
2
4
4
1
1
1
4
4
1
1
2
2
1
1
1
1
3
8
8
2
8
4
4
1
2
4
2
NOTES
8
IMPELLER
63 1

IMPORTANT: When ordering replacement parts, always give the model number, serial number of
the machine and part number. Also a brief description of each item and quantity
desired.
10-810
8360, Champ-d’Eau, Montreal (Quebec)
Canada H1P 1Y3
Tel.: [phone]
Fax : [phone]
www.general.ca