General Mfg SafTLite STUBBY II LED Guide

FORM # 9032-7292 (02/10)
KEEP THIS MANUAL
If this Worklight malfunctions or is in need of repairs, send to:
CUSTOMER SERVICE DEPARTMENT
1100 S. MORGAN ST.
BLUFFTON, IN 46714
PHONE: [phone]
1 Year Warranty
The Manufacturer warrants to the purchaser of this new light that it
was thoroughly tested and inspected and found to be in perfect
working order before leaving our factory. If within 1 year from the date
of purchase, any part of this worklight proves to be defective in
material or workmanship, such defective part will be repaired or
replaced (company option) free of charge, at our factory. The
company's liability in all events is limited to the purchase price paid.
The warranty does not apply to damage, alteration, misuse or abuse
not attributed to the Manufacturer, its representatives, dealers or their
employees. This warranty does not apply if the product is mishandled
or operated at a voltage exceeding, that shown on the product.
The Manufacturer has made a diligent effort to illustrate and describe
the products in its literature accurately, however such illustrations and
descriptions are for the sole purpose of identification and do not
express or imply a warranty that the products will necessarily conform
to the illustrations or descriptions.
CAUTION, IMPORTANT SAFETY INSTRUCTIONS: This port-
able lamp has a polarized plug (one blade is wider than the other) as a
feature to reduce the risk of electric shock. This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Never use an ex-
tension cord unless plug can be fully inserted. Do not alter the plug.
ATTENTION, INSTRUCTI0NS IMPORTANTES DE
SECURITE: Cette lampe portative a une fiche polarisante (une lame est
plus grande que l autre) comme caracteristique pour reduire le risque de
choc electrique cette fiche n’ engage q’ une prise polarisante. Si la fiche n’
engage pas completement la prise, alors renverser la, si elle n’ engage
toujours pas, metler vous en rapport avec un electrician qualifie. Ne ja-
mais utiliser avec un prolongateur si la fiche n’ engage pas completement.
Ne changer pas la fiche.
Warranty & Instruction Manual
Available with Scratch
And Chemical Resistant
Outer Tube.
STUBBY II ® LED

MOUNTING INSTRUCTIONS FOR MODELS with REEL
1. Select location within 2 feet of an electrical outlet. 1. Select location within 2 feet of an electrical outlet.
2. Take U shaped Bracket “A” and attach to solid 2. Screw the hanger Hook securely into the ceiling.
part of the wall or ceiling with screws provided. 3. Hang Reel on Hook.
3. Place Hanger Bracket “B” Inside U shaped 4. Close Hook with pliers to prevent Reel from
Bracket “A” lining up small holes in the Brackets. Coming off. Refer to point “A”.
4. Insert Locking Pin “C” through lined-up holes. Be 5. Adjust Cord Stop so light or outlet hangs at
sure to bend the end of locking pin as shown. Desired length when cord is retracted.
Care & Operation of your New
Stubby II LED Worklight
CAUTION
1. Inspect cord regularly for damage and replace if necessary for user safety.
2. Do not submerge in liquids.
3. When hanging reel models on ceiling:
- By Hook: Close hook with pliers to prevent reel from coming down.
- By Bracket Pin: With reel in place, bend end of “L” shaped pin to
prevent pin from falling out.
- Read mounting instructions carefully before installing.
4. Caution—Risk of Electrical Shock—Use in Dry Locations Only.
5. Tool Tap Models:
- Do not exceed Tool Tap amperage rating of 12 amps (16 AWG).
- Pull cord all the way out of reel when using the tool tap.
OPERATION & MAINTENANCE
1. Plug the unit into a 120 volt AC outlet. The power supply cord is UL listed and
meets OSHA standards for grounding of hand held tool.
2. Disconnect the power supply before servicing the light.
3. Keep the unit free from grease and dirt by using a damp cloth with mild deter-
gent, or waterless hand cleaners. This removes dirt from scratches in outer
tube and will provide the best output at all times. If tube is damaged or badly
scratched, it is easily replaced and is available as a replacement part.
4. Do not use solvents such as gasoline to clean unit or cord as it makes the parts
brittle. Do not allow brake fluid to contact outer tube as it will cause permanent
damage.
Item Part No. Description
1 5000-0733 Bumper ring
2 5000-1371 Outer tube assy, Polycarbonate (includes items 1 & 5)
2 5000-1372 Outer tube assy, X-Treme Shield (includes items 1 & 5)
3 5000-0760 Twin spring steel hook w/tips
4 5000-1373 LED board w/end lite and heat sink
4 5000-1374 LED board less end lite with heat sink
5 5000-1375 Reflector, Polycarbonate
5 5000-1376 Reflector, X-Treme Shield
Item Part No. Description
6 5000-0415 Handle 18/2 SVT cord (includes item 7)
6 5000-0416 Handle 18/2 SJTOW cord (includes item 7)
6 5000-0425 Handle 16/3 SJTOW cord (includes item 7)
7 5000-0213 Screw
8 5000-1187 Switch for LED board w/end lite (includes three of item 15)
8 5000-0477 Switch for LED board w/o end lite (includes two of item 15)
9 5000-0104 End cap, small black (18/2 SVT)
9 5000-0103 End cap, medium black (18/2 SJTOW)
9 5000-0741 End cap, large black (16/3 SJTOW)
10 5000-0479 Watertite clamp, large
11 5000-0480 Watertite clamp, small
12 5000-6300 Cord assembly, 1’ 16/3 SJTOW yellow
12 5000-6082 Cord assembly, 25’ 18/2 SJTOW yellow
12 5000-6084 Cord assembly, 25’ 16/3 SJTOW yellow
12 5000-6085 Cord assembly, 50’ 18/2 SJTOW yellow
12 5000-6087 Cord assembly, 50’ 16/3 SJTOW black
13 5000-6302 40’ 18/2 SJTOW Reel cord assembly, yellow (includes item 15)
13 5000-6281 40’ 16/3 SJTOW Reel cord assembly, yellow (includes item 15)
13 5000-6303 50’ 18/2 SVT Reel cord assembly, black (includes item 15)
14 5000-0775 Mounting hardware, 40 & 50’ reels
15 5000-0754 Closed end connector, insulated
16 5000-6304 40’ 18/2 SJTOW Reel assembly with mounting hardware
16 5000-6305 40’ 16/3 SJTOW Reel assembly with mounting hardware
16 5000-6160 50’ 18/2 SVT Reel assembly with mounting hardware
17 5000-1368 In-line Tool Tap assy