GENI IRDW-7024156-00D-11 User manual

3in1 LED Washer
IRDW-7024156-00D-11
User Manual
Instruction:
IRDW-7024156-00D-11 is a LED washer which is made of 24pcs 3W 3in1 RGB LED. With the functions of
DMX, Auto and manual modes.It can be controlled as 8 segments, 4 segments, 2 segmens and 1
segment. It can be in Master/ Slave mode. The effects are color changeable, dimmer, strobe and fade. It
is easy operation and easy installation, with a low price and well effect, especially suitable for the wash
of Home Party and Entertainment place.
Please read this manual before your use and keep it for your future reference.
Note:
Please use the to avoid any trouble for the fixture.
The operation temperature is below 40℃，humidity is 0~95％. If you use it out of this range, the fixture
will be shorten the lifespan.
Indoor use only
Caution:
Please do not connect the power when the fixture is still in the box.
Please do not connect the power before the installation. The fixture must be linked to the earth wire.
If you met the problem for this fixture, please call the engineer for the repair. Do not open the fixture by
yourself.
Please must use the same input voltage as per our instruction.
Technical Specification
1. Voltage: AC110-240V 50Hz/60Hz
2. Power consumption: 60W
3. Light Source: 3 in 1 RGB 24pcs LED
Page1of5

4. Function: DMX,Auto,Manual,Master/Slave
5.DMX Channel：7
6. Size: L1000*W57*H128mm
7.Net Weight:4.0 Kgs
Packing List:
zIRDW-7024156-00D-11 3in1 LED Washer -----------------------------------------------1PC
zPower Cable-------------------------------------------------------------------------1PC
zDMX Cable---------------------------------------------------------------------------1PC
zUser Manual ------------------------------------------------------------------------1PC
Backview:
1,LCD display 2,Switch “MENU”UP 3,Switch “MENU”DOWN 4、Security pothook 5,DMX input 6 , Power
input 7,Power output 8、DMX output
Installation：
Methods：This fixture can be used on the flat surface or hanging on the wall or ceiling. If you want to
hang it, please be sure that you have fixed the screw on the wall or ceiling very closely to avoid any
problems.
a) Flat surface installation
b) Hanging installation
Function:
I.Back Up
When powering on,the system will be back up to the original setting,and the fixture will return to the
working mode in which the fixture was powered off last time.
II.Menu and Display
Press the “UP” or “DONW” key continuously,the menu will display as below.
Page2of5
001~512 Pgx Spx Sbx
GxxBxx
XXX
Fdx
Rxx

Remarks：
X is the number from 0 to 9.
XX is the number from 00 to 10.
XXX is the temperature of the LED board.
III.Slave Mode：
1.DMX mode & Address setting：
Hold the button “MENU” until the mode is changed to the DMX mode, loose you finger, the working
mode will be changed to the DMX mode automatically. Also you can change the DMX address to press
“UP” or “DOWN” Button. If you hold the button of “UP” or “DOWN”, then the DMX address will be
changed rapidly. The address range is from 001 to 512.
2.DMX mode function chart:：
CH1 CH2 CH3 CH4 CH5 CH6~CH26
0~40 Black Out NA NA NA NA NA
41~80 Dimmer Flash All Red All Green All Blue NA
81~120 Dimmer Flash Red 1 Green 1 Blue 1 Red2,Green2,Blue2~Red8,Green8,Blue8
121~160Color
Flash Flash Color NA NA NA
201~240Color Speed NA NA NA NA
0~29
Programe
1
30~59
Programe
2
60~89
Programe
3
90~119
Programe
4
120~149
Programe
5
150~179
Programe
6
180~209
Programe
7
241~255 Dream
Flow Speed Fade
210~255
Programe
8
NA NA
3．DMX connector pin：
Male & Female DMX connector pin: Pin1 = Gnd Pin2 = Dmx- Pin3 = Dmx+
4，DMX Linking Method：
Page3of5

DMX Controller
DMX Linking Text：Use a 3 pin connector to connect the fixtures according to the above picture, each
fixture setted in the same address(address can be in 001-512), then they can work synchronization with
DMX signal.
IV. Master Mode
1. Auto mode:
Hold the button “MENU” until the mode is changed to the Auto mode, loose you finger, then the working
mode will be changed to the Auto mode automatically. Press “MENU” button to choose the different
code. Please see the picture as below, then press “UP” or “DOWN” button to change the code. If you
hold the button “UP” or “DOWN” button, the code will be changed rapidly.
Spx Sbx Fdx Pgx
Specification:
Prg XX(1~9): Choose the internal program, there are 9 internal programs.
Spd XX(1~9):Choose the speech of the internal program, there are 9 steps, 1 is the slowest and 9 is the
fastest.
Stb XX(0~9): Choose the frequency of strobe for the internal program.
Fad XX(0~9): Choose the fade of the internal program, there are 10 steps, 01 is the fastest and 9 is the
slowest.
Note: If you set up the strobe and fade together, the flash will be in the priority. If the Stb is not 0, Even
Fad is not 0, the fixture will run the strobe not fade program.
2.Manual mode
Hold the button “MENU” until the mode is changed to the Manual mode, loose you finger, then the
working mode will be changed to the Manual mode automatically. Press “MENU” button to choose the
different code. Please see the picture as below, then press “UP” or “DOWN” button to change the code.
If you hold the button “UP” or “DOWN” button, the code will be changed rapidly.
Gxx BxxRxx
Rxx(00~10):Set the brightness of the red LED.
Gxx(00~10):Set the brightness of the green LED.
Bxx(00~10):Set the brightness of the blue LED.
Page4of5

3.Temperature Display：
Hold the button “UP” or “DOWN” until the mode is changed to temperature display as below.
XXX:The temperature of the LED board
XXX
4. Linking Function：When the master fixture works in Auto or Manual mode,the slave fixture in DMX.
will work synchronously.
Trouble Shooting：
Problems Check list Trouble Shooting
The machine does
not work.
1. If your power us same as the input of
the machine.
2. If the fuse is broken.
1. Make sure the voltage.
2. Replace the same fuse.
LED dimmed If your power us same as the input of
the machine. Make sure the voltage input.
No DMX input 1．If the polarity is opposited in the DMX controller.
2．If it is in DMX mode.
1．Correct the DMX polarity.
2．Change to the DMX mode.
Page5of5