www.GenieCompany.com/commercial | 800.843.4084
Wiring Diagram
GCL-MH
MEDIUM-DUTY HOIST OPERATOR
©2012 The Genie Company
Rev.
Level
ECN
Number
Revision
Rev. Date Apvd. Date
emaNtraP.oNtraP
COMPONENTS
Size
Drawing No.
Sheet No.
The drawings and all other information contained
herein are the confidential and proprietary property
of Overhead Door Corporation and its affiliated
companies. This drawing and information, in
whole or in part, may not be copied in any manner
or disclosed to anyone without the prior written
consent of Overhead Door Corporation. No
disclosure of any of this drawing or information
is intended to operate as a license or authorization
to use it for any purpose without the specific
written consent of Overhead Door Corporation.
Scale Drawing Size
B
Drawn
By
Apvd.
By
Reference Drawing No.
Date
Material:
Tolerance Unless Otherwise Specied
2 Place Decimal ± Angular ±
3 Place Decimal ± Holes ±
A Subsidiary of
Overhead Door Corporation
22790 Lake Park Blvd.
Alliance, Ohio 44601
Part Name
LABEL SPECIFICATIONS:
1. 6.50" Max. Roll Dia.
2. Roll Winds. Per vendor tooling recommendation, unless specied.
3. Corner radius to be within .00/.16 range typ. unless specied.
4. Specied corner radius
5. Label must be U.L. and C.S.A. approved for use on (
), max. temp 60°C and where exposed to
high humidity.
6. Each roll of labels and each carton of labels must be marked with
the manufacturers U.L. designation for this label.
O.T. O.B. O.R. O.L.
Printing Info:
L1/L1 N/L2
GND
PWR RAD GND
OPEN CLOSE STOP GND 1-BTN N/O
SAFETY
N/O
SAFETY
ODC
STB
ODC
STB
EXT
INTLK
EXT
INTLK
OPEN
CLOSE
STOP
1-BTN
STATION
KEY
SWITCH
STATION
CARD
READER
O/C
PULL
SWITCH
RELAY
GND
NOM
+ 24VDC
SENSING EDGE SWITCH
N/O
N/O
N/O
N/O
3-BUTTON
STATION SERIES II (STB) PHOTOCELLS
+
-
+
-
THRU-BEAM
PHOTOCELLS
RADIO
REMOVE JUMPER
WHEN INSTALLING
EXTERNAL INTERLOCK
CONTROL SIGNAL TERMINAL STRIP
PWR
20-40 VDC @ 300MA
MAX CURRENT
MULTIPLE 3-BUTTON
STATION INSTALLATIONS
REQUIRE THE STOP
BUTTON TO BE WIRED
IN SERIES
REMOVE JUMPER
IF STOP BUTTON
IS USED
LINE IN
POWER CONNECTIONS CLASS 2 SUPPLY 20-40 VDC
120V
240V
EXTERNAL RADIO TERMINAL STRIP
CLASS 2 SUPPLY 20-40 VDC
(*CONNECT STB WIRES TO EITHER TERMINAL)
LINE
(HOT) NEUTRAL
LINE 1 LINE 2
*
OPEN CLOSE STOP GND 1-BTN N/O
SAFETY
N/O
SAFETY
ODC
STB
ODC
STB
EXT
INTLK
EXT
INTLK
L1 N
ROUTE LOW VOLTAGE
WIRING AS SHOWN
PLUG UNUSED HOLES
LINE INPUT
TERMINALS
CONTROL
WIRE
TERMINALS
RADIO
CONTROL
TERMINALS
LINE
GROUND
STB
ENAB
+ 24
VAC
EXT
INTLK
HOIST
INTLK
TROUBLESHOOTING
LED'S
RADIO FUSE
SECONDARY
FUSE
EXPANSION
MODULE
MOUNTING
LOCATIONS
TRANSFORMER
CONNECTOR
HOIST INTERLOCK
CONNECTOR
REPLACE RADIO
FUSE WITH
GDC-315mA OR
S504-315mA ONLY
REPLACE SECONDARY
FUSE WITH
GDB-2A OR
S500-2A ONLY
FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE FUSES ONLY WITH THE SAME TYPE AND RATIN
MOTOR CONNECTOR
BRAKE CONNECTOR
EXPANSION
PORT
(CLASS 2 CONNECTIONS)
SECOND TRANSFORMER
MOUNTING LOCATION
(OPTIONAL)
ROUTE LINE VOLTAGE
WIRING AS SHOWN
PLUG UNUSED HOLES
RADIO CONNECTOR
NOT FOR RESIDENTIAL USE
CAUTION: To prevent the motor protector from tripping, do not exceed 15 cycles of opening and closing
per hour. For limited-duty ONLY. 110851.0001
STB DISABLED OR STB WIRING SHORT
NORMAL OPERATING CONDITION
HOIST INTERLOCK SWITCH OPEN:
1.) HOIST RELEASE NEEDS RESET.
2.) HOIST INTERLOCK CONNECTOR NOT PLUGGED IN.
3.) HOIST INTERLOCK DEFECTIVE.
POWER SUPPLY PROBLEM:
1.) CHECK AC POWER SUPPLY.
2.) CHECK MAIN POWER FUSE.
3.) CHECK SECONDARY FUSE (2A)
110851-0001
NTS
1 OF 1
.03
DECAL, WIRING
DIAGRAM, MX
WDR 9/1/05
110103-0001
-ORIGINAL ISSUE
BLACK PRINTING ON WHITE
8 PT C1S TAG MATERIAL WITH PERMANENT
ADHESIVE. UV GLAZEKOTE FINISH. SLIT BACK.
LABELS SUPPLIED FLAT. VERTICAL BACK SLIT
1.25” FROM LEFT EDGE.
15.25 X 7.00
JW 9/6/05
35711
.25 TYP
EXTRA
BACKING
ADDED EXTRA BACKING
35868A
7.00
LABEL
SIZE
15.25
LABEL SIZE
J.W. 10-31-05
35963
B15 CYCLES WAS 12
J.W. 2-7-06
Rev.
Level
ECN
Number
Revision
Rev. Date Apvd. Date
emaNtraP.oNtraP
COMPONENTS
Size
Drawing No.
Sheet No.
The drawings and all other information contained
herein are the confidential and proprietary property
of Overhead Door Corporation and its affiliated
companies. This drawing and information, in
whole or in part, may not be copied in any manner
or disclosed to anyone without the prior written
consent of Overhead Door Corporation. No
disclosure of any of this drawing or information
is intended to operate as a license or authorization
to use it for any purpose without the specific
written consent of Overhead Door Corporation.
Scale Drawing Size
B
Drawn
By
Apvd.
By
Reference Drawing No.
Date
Material:
Tolerance Unless Otherwise Specied
2 Place Decimal ± Angular ±
3 Place Decimal ± Holes ±
A Subsidiary of
Overhead Door Corporation
22790 Lake Park Blvd.
Alliance, Ohio 44601
Part Name
LABEL SPECIFICATIONS:
1. 6.50" Max. Roll Dia.
2. Roll Winds. Per vendor tooling recommendation, unless specied.
3. Corner radius to be within .00/.16 range typ. unless specied.
4. Specied corner radius
5. Label must be U.L. and C.S.A. approved for use on (
), max. temp 60°C and where exposed to
high humidity.
6. Each roll of labels and each carton of labels must be marked with
the manufacturers U.L. designation for this label.
O.T. O.B. O.R. O.L.
Printing Info:
L1/L1 N/L2
GND
PWR RAD GND
OPEN CLOSE STOP GND 1-BTN N/O
SAFETY
N/O
SAFETY
ODC
STB
ODC
STB
EXT
INTLK
EXT
INTLK
OPEN
CLOSE
STOP
1-BTN
STATION
KEY
SWITCH
STATION
CARD
READER
O/C
PULL
SWITCH
RELAY
GND
NOM
+ 24VDC
SENSING EDGE SWITCH
N/O
N/O
N/O
N/O
3-BUTTON
STATION SERIES II (STB) PHOTOCELLS
+
-
+
-
THRU-BEAM
PHOTOCELLS
RADIO
REMOVE JUMPER
WHEN INSTALLING
EXTERNAL INTERLOCK
CONTROL SIGNAL TERMINAL STRIP
PWR
20-40 VDC @ 300MA
MAX CURRENT
MULTIPLE 3-BUTTON
STATION INSTALLATIONS
REQUIRE THE STOP
BUTTON TO BE WIRED
IN SERIES
REMOVE JUMPER
IF STOP BUTTON
IS USED
LINE IN
POWER CONNECTIONS CLASS 2 SUPPLY 20-40 VDC
120V
240V
EXTERNAL RADIO TERMINAL STRIP
CLASS 2 SUPPLY 20-40 VDC
(*CONNECT STB WIRES TO EITHER TERMINAL)
LINE
(HOT) NEUTRAL
LINE 1 LINE 2
*
OPEN CLOSE STOP GND 1-BTN N/O
SAFETY
N/O
SAFETY
ODC
STB
ODC
STB
EXT
INTLK
EXT
INTLK
L1 N
ROUTE LOW VOLTAGE
WIRING AS SHOWN
PLUG UNUSED HOLES
LINE INPUT
TERMINALS
CONTROL
WIRE
TERMINALS
RADIO
CONTROL
TERMINALS
LINE
GROUND
STB
ENAB
+ 24
VAC
EXT
INTLK
HOIST
INTLK
TROUBLESHOOTING
LED'S
RADIO FUSE
SECONDARY
FUSE
EXPANSION
MODULE
MOUNTING
LOCATIONS
TRANSFORMER
CONNECTOR
HOIST INTERLOCK
CONNECTOR
REPLACE RADIO
FUSE WITH
GDC-315mA OR
S504-315mA ONLY
REPLACE SECONDARY
FUSE WITH
GDB-2A OR
S500-2A ONLY
FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE FUSES ONLY WITH THE SAME TYPE AND RATIN
MOTOR CONNECTOR
BRAKE CONNECTOR
EXPANSION
PORT
(CLASS 2 CONNECTIONS)
SECOND TRANSFORMER
MOUNTING LOCATION
(OPTIONAL)
ROUTE LINE VOLTAGE
WIRING AS SHOWN
PLUG UNUSED HOLES
RADIO CONNECTOR
NOT FOR RESIDENTIAL USE
CAUTION: To prevent the motor protector from tripping, do not exceed 15 cycles of opening and closing
per hour. For limited-duty ONLY. 110851.0001
HOIS T
EXTERNAL
24 VOLTS
STB
INDICATION
OFFSTB DISABLED OR STB WIRING SHORT
ON STB ENABLED
ON ON ON NORMAL OPERATING CONDITION
OFFON ON
HOIST INTERLOCK SWITCH OPEN:
1.) HOIST RELEASE NEEDS RESET.
2.) HOIST INTERLOCK CONNECTOR NOT PLUGGED IN.
3.) HOIST INTERLOCK DEFECTIVE.
OFFOFFON EXTERNAL INTERLOCK OPEN
OFFOFFOFF
POWER SUPPLY PROBLEM:
1.) CHECK AC POWER SUPPLY.
2.) CHECK MAIN POWER FUSE.
3.) CHECK SECONDARY FUSE (2A)
110851-0001
NTS
1 OF 1
.03
DECAL, WIRING
DIAGRAM, MX
WDR 9/1/05
110103-0001
-ORIGINAL ISSUE
BLACK PRINTING ON WHITE
8 PT C1S TAG MATERIAL WITH PERMANENT
ADHESIVE. UV GLAZEKOTE FINISH. SLIT BACK.
LABELS SUPPLIED FLAT. VERTICAL BACK SLIT
1.25” FROM LEFT EDGE.
15.25 X 7.00
JW 9/6/05
35711
.25 TYP
EXTRA
BACKING
ADDED EXTRA BACKING
35868A
7.00
LABEL
SIZE
15.25
LABEL SIZE
J.W. 10-31-05
35963
B15 CYCLES WAS 12
J.W. 2-7-06
