GENUV G T1 Series Installation and operating instructions

Application Note
1. Features of LO2/2.1 & LOHT series
- UV measuring in Air (and High temperature)
- Custom products can be supplied.
- Output type : DC 0~5 V or 4~20 mA
- Operation voltage : DC 5 V or 9~24 V
- NIST, KRISS traceable calibration possible
3. The features and advantages of the product
- Highly visible barrier : pure ultraviolet light (UVA, UVB, UVC)
sensors using. No need for a separate filter
- Custom product supply available to meet customer orders
- Calibration service offers tailored to customers' requests
- Reliable implementation at an affordable price
ProbeApplication Guide lines for LO2/2.1 and LOHT series
5. Point that must be taken into account in product selection
- Consider the Detection type (UVV/UVA/UVB/UVC/Visible,
case for LO2/2.1)
- Select maximum detection power range
- Check the operating voltage (5 V or 9~24 V) and
output type (Voltage or Current)
- The chosen cable length (5 m standard, customized available,
Max. 10 m)
- The chosen fiber length (1.5 m standard, customized available)
GUVx-T1xGC-3LO2.1
GUVx-T1xGC-I8LO2.1
6. Summary
Gxxx-T1xxC-3LO2
Gxxx-T1xxC-I8LO2
GUVS-T10EC-3LOHT
GUVS-T10EC-I8LOHT
Product photos
Product
Name
Measuring
Direction
Configuration
Type of Fiber
Detection
Wavelength
Fiber
Temperature
Banding
Radius
LO2
Front
(170°)
Sensor probe /
Optical fiber
1.5mm
GVBL : 330 ~ 445 nm
GVGR : 300 ~ 510 nm
GUVS : 400 ~ 700 nm
Max. 250 ℃
≥ 20
LO2.1
Front
(170 °)
Sensor probe /
Optical fiber
1.5mm
GUVV : 230 ~ 395 nm
GUVA : 220 ~ 370 nm
GUVB : 220 ~ 320 nm
GUVC : 220 ~ 280 nm
Max. 250 ℃
≥ 20
LOHT
Lateral
(360 °)
Detecting head /
Sensor probe /
Optical fiber
1.5mm
220 ~ 390 nm
Max. 250 ℃
≥ 20
2. Applications
- UV curing system
- UV Exposure system
- Air treatment system
- Flame sensing
4. Advantage of using a UV sensor probe
- Can accurately measure the intensity values of the chamber inside
- UV lamp intensity control based on measure intensity
- Can be monitored ON / OFF status of a UV lamp
- UV light can be seen for lamp replacement time
7. Design of fiber screw (The other one SMA905)
M4 X 20 mm
30 mm
[LO Series]
8. Measuring direction
UV Light source
Panel M8 Nut
[LO2/2.1]
Optical
fiber
UV Light
sources
Detecting head
Detecting head
Front
measuring Lateral measuring
[LOHT]
Fiber
Fiber
Fiber

9. Wiring connections
1) To connect the wiring, check the connection terminals.
The color-coded terminals are available as follows.
2) Black and white lines (GND) are connect to the internal sensor
probe
3) How to connect
Red : Vcc 5V or 9~24V
Black : GND
Green : Vout
White : GND
※If you connect wrong polarity it will cause the module
damaged or broken.
PLC or Multimeter
Power Supply
color
terminals
Remark
Red
Vcc
DC 5V or 9~24 V
Black
GND
Green
Vout
DC 0~5V or 4~20 mA
White
GND
• GUVD-MG02S connections
- GUVD-MG02S Diagrams (Vout)
1) Connect AC power to #1 and # 2 , and connect GND wire #5.
2) Connect Red wire to #11(Vcc) , Black wire to #12(GND) ,
White wire to #5(GND) , Green wire to #7(Vout)
⑪⑫⑬⑭⑮⑯⑰⑱⑲⑳
①②③④⑤⑥⑦⑧⑨⑩
System Power
AC 100~240V
+ –
Sensor Power
DC 20V Sensor Output
Max: DC 5V
+
(System GND)
–
- GUVD-MG02S Diagrams (Iout)
1) Connect AC power to #1 and # 2 , and connect GND wire #5.
2) Connect Red wire to #11(Vcc) , Black wire to #12(GND) ,
White wire to #5(GND) , Green wire to #6(Iout)
⑪⑫⑬⑭⑮⑯⑰⑱⑲⑳
①②③④⑤⑥⑦⑧⑨⑩
System Power
AC 100~240V
+ –
Sensor Power
DC 20V Sensor Output
4 –20mA
+
(System GND)
–
GUVx-T1xGC-3LO2.1
GUVx-T1xGC-I8LO2.1
GUVS-T10EC-3LOHT
GUVS-T10EC-I8LOHT Gxxx-T1xxC-3LO2 Gxxx-T1xxC-I8LO2

• Connection diagram of MG-05
-GUVD-MG05S Diagrams
1) Connect Ac power to #1 and # 2
2) Connect Green wire to #18(Vin), Red wire to #19(Vcc = +5V) ,
Black & White wire to #20 (GND)
⑪⑫⑬⑭⑮⑯⑰⑱⑲⑳
①②③④⑤⑥⑦⑧⑨⑩
System Power
AC 100~240V
18 : Vin
19 : +5V
20 : Ground
Sensor Input
11. IP Grade
- IP grade of LO series is IP40. (Do not use underwater)
92(-0,+0.5)
45 (-0,+0.5)
Panel Cut Out(mm)
12. Connector Pin number (Lo Probe)
2
3
4
1
5
2
3
4
1 5 1 : GND(Black)
3 : Vcc(Red)
5 : Vout or
Iout(Green)
13. Trouble shooting when the output signal is not out
1) Make sure that wiring is properly wired
2) Supply voltage (5V or 9~24V) Check if supply is being properly
3) Check lighting of the light source (UV lamp)
4) Ensure that the connectors are not separated
5) Ensure that the UV Sensor probe is installed correctly
- It has been installed correctly towards the direction of the UV lamp?
- Detection Power range is set too high compared to the amount of
irradiation
ex) The maximum measurement range is 1,000 ㎽/㎠, and when the
amount of irradiation 5 ㎽/㎠less
6) Check light source (UV Lamp type) and Sensor type
10. Panel cutting size
- GUVD-MG02S, GUVD-MG05S have same panel cutting size
1 : GND
3 : Vcc
5 : Vout or Iout
GUVx-T1xGC-3LO2.1
GUVx-T1xGC-I8LO2.1
GUVS-T10EC-3LOHT
GUVS-T10EC-I8LOHT Gxxx-T1xxC-3LO2 Gxxx-T1xxC-I8LO2

14. Product Handling Precautions
- Do not expose your eyes and skin, UV light is very dangerous
- Handling the UV lamp you should wear safety gear such as goggles
When you install the product ,
Turn off the Power source
15. A/S request in case of product failure
1) Should any failure is found in product, please call the
sales company or customer center for A/S
2) Product warranty period is 1 year from the date of
procurement with no charge. However, failure which
caused by user’s misuse or carelessness within warrant
period or any failure after the warrant period shall be
chargeable for it’s A/S
3) Product inquiry and on-line customer service :
[e-mail] (http://www.geni-uv.com)
GUVx-T1xGC-3LO2.1
GUVx-T1xGC-I8LO2.1
GUVS-T10EC-3LOHT
GUVS-T10EC-I8LOHT Gxxx-T1xxC-3LO2 Gxxx-T1xxC-I8LO2