GENUV MG-08 User manual

Genicom Co., Ltd Page 1
Manual
GUVX-T1XGS8
Radiometer 8
20210310-V0.1-CH.LEE

Genicom Co., Ltd Page 2
MG-08
GUVX-T1XGS8-L(LA9.2)
User Manual

Genicom Co., Ltd Page 3
Description : GUVX-T1XGS8-L series is portable instruments with LCD display.
GUVX-T1XGS8-LA9.2 series is probe type portable instruments with LCD display.
* Customization is available (Maximum of detection power : 10W/㎠)
Item TOTAL UV
(UVA+B) UVB UVC UVC –LED Far UV Blue light UV INDEX
Model Name
1)GUVV-
T10GS8
2)GUVB-
T11GS8
3) GUVC-
T10GS8
4)GUVL-
T11GS8
5)GFUV-
T10GS8
6)GVBL-
T12GS8
7)GUVI-
T11GS8
Detection 0.00 ~ 99.99 ㎽/㎠* 0~50.0 UVI
Spectral
Detection
Range
230 ~ 395 n
220 ~ 320 n
220 ~ 280 n
220 ~ 320 n
~250nm
330 ~ 445
220 ~ 320nm
Calibration
Peak Point
365 nm
(LED)
306 nm
(Lamp)
254 nm
(Lamp)
285 nm
(LED)
222nm
r
lamp
385/405 nm
(LED)
Solar
simulator
Resolution 0.1 uW/㎠0.1 UVI
Function Absolute Power (㎽/㎠), DOSE (J/㎠, Accumulative time : Max. 24hour.),
Max Power (㎽/㎠) Index(UVI)
Conversion
2 Times /Sec
Display 128x64 Graphic LCD
LCD Size 17 x 35 ㎜
Operation 0 ~ 60 ℃
Operation RH 10 ~ 85 %
Accuracy ±10 % (NIST Traceable)
Product Size
73 x 139 x 31 ㎜
Weight Main body : 100 g (without battery)
Power Source
DC 9V Battery
1. Product Feature and Specifications

2021-V0.1-CH.LEEPage 4
Wear protective gear when monitoring UV lamps.
Allow lamps to warm-up prior to taking reading
(at Least 5 minutes).
Do not subject the meter to extremes in temperature, humidity,
When the surface contamination of the product, wipe with a
Keep sensor free of oil, dirt, etc.
Do not disassemble if modification.
1) GUVV-T10GS8-L(LA9.2) 2) GUVB-T11GS8-L(LA9.2) 3) GUVC-T10GS8-L(LA9.2)
4) GUVL-T11GS8-L(LA9.2)
7) GUVI-T11GS8-L(LA9.2)
6) GVBL-T12GS8-
L(LA9.2)
5) GFUV-T10GS8-L(LA9.2)
2. Relative Response Curve
3. Warning

Genicom Co., Ltd Page 5
②LCD Diaplay
[UV Radiometer 8 front side]
④Function Button
④Function Button
③Function Display LED
①Light-receiving Unit
②LCD Display
This is 4-digit LCD display.
③Function Display LED
Red : Logging
Green : DOSE
Yellow : UVC SAFE
⑤Function Button
OK Button : Press 1 second to perform logging/more 3 second to enter menu
ESC Button : Press 1 second to reset DOSE value and Max. Power.
Press short to measure pause, start
UP Button : Press 1 second to perform DOSE, Press again for 1 second to stop DOSE.
DOWN Button : Press 1 second to set information mode, DOSE graph, UVC Safe
measurement mode.
④Function Button
④Function Button
4. Part Names
4-1) Front side ①Light-receiving Unit

2021-V0.1-CH.LEEPage 6
①Product Information Sticker
②Battery Cover
This is a 9V battery cover.
Open the battery cover to insert and replace the battery.
③Inside of the Battery Cover
the Serial number is here.
[UV Radiometer 8 back side]
Model Name
Product Name
Measurement wavelength range
①Products Information Sticker
②Battery Cover
Model No. : GUVX-T1XS-L
Type : UV Index Meter
Detection Range : XXX-XXX nm
Power Range : 0~100.0 ㎽/㎠
NIST Traceable
Made in KOREA by
Genicom Co., Ltd.
www.geni-uv.com
Measurement light power range
Model No. : GUV X-T1XS7.1-L
Type : UV Index Meter
Detection Range : XXX-XXX nm
Power Range : 0~100.0 mW/㎠
NIST Traceable
Made in KOREA by
Genicom Co., Ltd.
www.geni-uv.com
③Inside of the Battery Cover
S8-001
4-2) Back side

Genicom Co., Ltd Page 7
Open the battery cover in the back of main unit and check for a 9V battery is or
isn’t.
Pulling the connector forcibly can cause it to break.
Please hold the battery connector and detach the battery
5. Product Operation Guide
5-1) Battery check
5-2) Warning for battery replacement

2021-V0.1-CH.LEEPage 8
uW/Cm2
323.0
20/12/17 11:52:32
Press OK button for 1 second to start logging. Press again for 1 second to exit at
logging.
Press shortly
(Power ON)
Press 3
second
(Power OFF)
Press UP button for 1 second to start DOSE. Press again for 1 second to exit at DOSE.
Press 1
second
(logging )
Measurement Mode Logging
Mode
1Press 1
second
(DOSE)
Measurement
Mode
DOSE Mode
SN:MG08201217001
uW/Cm2
323.0
20/12/17 11:52:32
323.0
20/12/17 11:52:32
Logging uW/Cm2
323.0
20/12/17 11:52:32
DOSE uW/Cm2
5-3) Power ON and Off
5-4) Function Button
Press the ESC button shortly for power ON, Press 3 second for Power OFF.

Genicom Co., Ltd Page 9
00:00:00 323 uW/Cm2
Information Mode
00:00:00 323 uW/Cm2
323.0 323.0 0.000
323.0
20/12/17 11:52:32
uM
Cm2
Press the DOWN button for 1 second to cycle into measurement mode,
information mode, DOSE Graph mode, UVC Safer mode and measurement
mode.
Press 1
second
(UVC SAFE)
DOSE GRAPH Mode
UVC SAFE
Mode
00:00:00 323 uW/Cm2
323.0
UVC SAFE
uM
Cm2
Measurement Mode
uW/Cm2
323.0
20/12/17 11:52:32
Press 1 second
(Information
Mode)
Press 1
second
(DOSE
GRAPH)
Press 1 second
(Measurement
Mode)

2021-V0.1-CH.LEEPage 10
Press the ESC button for 1 second to resets DOSE, Min, Max, Avg,
and measured values to 0.
Press 1 second
(zero Set )
Measurement Mode Zero set
uW/Cm2
323.0
20/12/17 11:52:32
uW/Cm2
0.000
20/12/17 11:52:32
Press the ESC button shortly to pause the measured value. Press again shortly to
displays the measured value.
Press shortly
(HOLD )
Measurement Mode HOLD
uW/Cm2
323.0
20/12/17 11:52:32
uW/Cm2
20/12/17 11:52:32
323.0