Geovent GEOFILTER Oil 100 User manual

GEOFILTER OIL
INSTRUCTION MANUAL
www.geovent.com
Version 1.0 16.07.21

2

3
Contents
1.0 Introduction ..............................3
2.0 Safety ..................................3
2.1 General safety .......................... 3
2.2 Danger .................................3
3.0 Machine overview ........................ 4
3.1 Description ............................. 4
3.2 Intended use ............................ 4
3.3 Machine specifications .................... 4
3.3.1 Design ............................... 4
3.3.2 Technical data ......................... 4
4.0 Transport, handling and storage . . . . . . . . . . . . . 4
5.0 Assembly, installation and start of operation ... 4
5.1 Location ............................... 4
5.2 Installation ............................. 5
5.3 Control and test of the security system ........5
6.0 Commissioning .......................... 5
6.1 After installation ......................... 5
7.0 Control, test and maintenance .............. 5
7.1 Control ................................ 5
7.2 Maintenance .............................5
7.3 Replacing filter............................5
8.0 Cleaning ................................6
9.0 Troubleshooting ......................... 7
10.0 Dismantling, disabling and scrapping ........ 7
11.0 Dimensions ............................ 7
12.0 Liability ............................... 8
13.0 Declaration of conformity ................. 8
14.0 Spare part list .......................... 9
1.0 Introduction
This manual is made and designed in order to facilitate
the best and most secure interaction with the product.
The manual is relevant for people involved in transpor-
tation, stocking, installation, using, maintaining and all
other thinkable interaction with the product.
The manual must be read in full and understood before
interacting with the product.
When the manual has been read and understood in full,
the table of contents can be used to find the relevant
information in each case.
The product is manufactured by:
Geovent A/S
Hovedgaden 86
DK-8861 Løgstrup
DENMARK
Tel.: [phone]
E-mail: [email protected]
www.geovent.com
This manual is to be used for all interactions with the
product including: Transportation, stocking, installation,
operation and maintenance.
This product is marked with: (example)
2.0 Safety
2.1 General safety
Carefully read this manual before use and observe the
safety instructions in order to avoid injuries!
Keep this manual in a safe place!
Secure that all users of the product have read this ma-
nual and that they follow the instructions as described.
Observe all instructions marked on the product!
Observe the indications of the manufacturer.
Never use the product if you are in doubt about how it
works or what you should do.
When doing maintenance follow the instructions in chap-
ter 7.0.
Do not modify the product or use spare parts from other
suppliers than Geovent, as this may hamper the product
and the function.
2.2 Danger
You must wear safety gloves when handling or using the
product to protect your hands from scratches etc.
Be aware that the product may tilt when you move it.
You must handle the product with care and tie it safely to
the truck or the fork lift when it is in transport.
Follow the instructions in chapter 7.0 when the product
is maintained.

4
Spiro duct ø100 mm
ASA-arm
with hood ø100 mm
Geofilter Oil 100
Box fan
MSFG 200-3
Spiro duct ø200 mm
When handling the product be sure that the there is no
risk for the installer, and secure that there are no people
around the product, secure that the product cannot fall
down risking to injure persons or subjects.
The product is not to be used in areas categorised as
ATEX zones, e.g. with dust from aluminium, flour, wood,
and other mediums that present an explosion hazard.
If a repair is not possible you should dispose of the pro-
duct. Please follow the instruction for disposal in chapter
10.0.
3.0 Machine overview
3.1. Description
GeoFilter Oil is used to remove oil mist from e.g. cutting
machines so that the oil does not reach the central pipe
system.
This prevents the oil from condensing in the pipe system.
3.2 Intended use
It is recommended to use an oil mist filter for at each
machine to avoid oil in the central extraction system.
The filter medium, which is made of aluminum, can be
removed via the removable bottom.
The bottom is provided with a tap for draining separated
oil, which can be recycled.
Example of an installation
3.3 Machine specifications
3.3.1 Design
Cabinet: Galvanized steel
Powder coated
Filter medium: 400x400, Aluminum filter medium or
400x600, Aluminum filter medium
3.3.2 Technical data
Dimensions
Model/Dimension A
[mm]
B
[mm]
Inlet
[mm]
GeoFilter Oli 100 400 400 ø100np
GeoFilter Oli 160 400 600 ø160np
Model/Dimension Outlet [mm] Weight [kg]
GeoFilter Oli 100 ø100np 7,0
GeoFilter Oli 160 ø160np 9,2
4.0 Transport, handling and storage
During transport in a truck or in another means of trans-
portation the product must be securely packed in a box
or a pallet and covered with a water proff material.
The product must be securely stowed in the truck so that
it will neither tilt nor shift during transport.
During transport over a short distance e.g. in a stock or
a factory, the product can be moved by means of a for-
klift or a stabeler.
When moved it must be secured that the product does
not tilt or shift. And it must be secured that the limitations
of the means of transportation is not exceeded.
Secure that there are no people around the product,
when the product is moved.
The product must be placed in a dry place and covered
securely, in order to secure that moist, metal parts or
other substances do not damage the product.
It is not allowed to place anything on top of the product.
5.0 Assembly, installation and start of
operation
5.1 Location
To ensure a fault-free function, the product must be in-
stalled indoors. Outdoor installation is not recommen-
ded.
Before installing the product, make sure that an optimal
location is chosen. Is there room for the product? Is the-
re room for maintenance and filter change?

5
5.2 Installation
GeoFilter Oil must be installed indoors. Outdoor installa-
tion is normally not recommended.
GeoFilter Oil is supplied complete and ready for instal-
lation.
Before installation consider the best placement for the
GeoFilter Oil. Is there space enough for carrying out sa-
tisfactory installation/-service of the filter?
The following installation should be done by a trained
professional.
5.3 Control and test of the security system
Before use the function of the filter should be tested.
Make sure that the entire installation is air tight.
If a whistling sound is heard, then locate the leak and
seal it using flexible mastic.
The entire extraction installation should be checked at
least once a year by a qualified service technician.
Periodic maintenance:
Check the oil particle filter at regular intervals. Clean it if
it needs to. If it is densely covered with oil that cannot be
cleaned off, the filter mat must be replaced.
6.0 Commissioning
6.1 After installation
Check the installation according to chapter 5.3.
7.0 Control, test and maintenance
7.1 Control
Check the installation according to chapter 5.3.
7.2 Maintenance
Check the oil filter at regular intervals.
Clean it if it needs to. If the oil cannot be cleaned off, the
filter mat must be replaced.
7.3 Replacing filter
Below is an instruction for change of filter.
Remark: The change of the lter medium which is illu-
strated in this manual, is on a lter, which is not installed.
The lter unit is tuned upside down in the illustrations.
However, the process is the same if the lter is installed.
1. Click the lock open.
2. Lift off the lid.
3. Gently bend the bracket about an inch upwards.

6
4. Loosen the filter medium by pushing it forward.
Grab the filter at the metal frame.
5. Pull up the filter medium.
6. The filter frame must be placed within the bracket in
the opposit end of the filter cabinet.
7. Insert the new filter medium.
Gently fit it into the frame.
Push it all the way to the bottom of the filter cabinet.
8. Gently push the filter medium into place. It may be ne-
cessary to lift the filter up a littel to make it fit. Afterwords
the lid is placed on the filter cabinet and lucked.
8.0 Cleaning
The outside of the product is cleaned with a vacuum
cleaner or a cloth.

7
9.0 Troubleshooting
In case of troubles please check the following issues:
• If there is a large pressure drop across the filter, the
filter medium must be replaced.
• If the oil does not separate in the filter, the filter medium
will probably need to be replaced.
• If there is oil in the filter cabinet, the drain may be
blocked.
10.0 Dismantling, disabling and scrapping
It is important that these instructions are followed to avo-
id contamination of persons or the environment.
Protective equipment must be worn before separation,
gloves, goggles, respirator and protective suit,
to avoid injuries.
When disposing of the product, the filter medium must
be removed and disposed of according to local rules and
regulations.
Clean the inside of the product with a cloth. Dispose of
the cloth according to local rules and regulations.
Dismantle plastic parts and dispose of it according to
local regulations.
Dismantle and separate metal parts by screwing them
apart. Then cut larger parts into smaller pieces and dis-
pose of it according to local rules and regulations.
Packaging must be sorted and disposed of in accordan-
ce with local regulations and regulations.
11.0 Dimensions
GeoFilter Oil 100
GeoFilter Oil 160

8
12.0 Liability
Warranty
Geovent A/S grants a warranty for products, which are
defective, when it can be proved that the defects are due
to poor manufacture or materials on the part of Geovent.
The warranty comprises remedial action (reparation or
exchange) until one year after the date of shipment.
No claims can be made against Geovent A/S in relation
to loss of earnings or consequential loss as a result of
defects on products from Geovent.
Wear on parts such as filter cartridges and hose is not
included in the warranty.
User liability
In order for Geovent to be capable of granting the decla-
red warranty, the user/fitter must follow this instruction
manual in all respects.
Under no circumstances may the products be changed
in any way, without prior written agreement with Ge-
ovent A/S.
Please refer to the current sales and delivery conditions
at www.geovent.com

9
14.0 Spare part list
Art. No. Description
15-030 Seperate alu filter medium 400x400
15-031 Seperate alu filter medium 400x600
13.0 Declaration of conformity
The manufacturer: GEOVENT A/S
HOVEDGADEN 86
DK-8831 LØGSTRUP
Hereby declares that:
The product: GeoFilter
Model: GeoFilter Oil 100,
GeoFilter Oil 160
Complies with the relevant parts of the following directi-
ves and standards:
Directive 2006/42 / EC of the European Parliament and
of the Council of 17 May 2006 on machines and amen-
ding directives 95/16 / EC
This declaration is no more valid if changes are made to
the product by others than the manufacturer.
Authorized to collect the technical file:
Lise Cramer
Date: 16.07.2021
Position: Director
Name: Thomas Molsen
Signature: ____________________________

10

11

HOVEDGADEN 86 • DK-8831 LØGSTRUP
([phone] • [email protected]