GeoVision GV-EBD4700 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual forfuture use. EBDV10-QG-A
Quick Start Guide
GV-EBD4700 IR Eyeball IP Dome

© 2016 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademarks of Microsoft Corporation.
November 2016

i
Contents

Note for Connecting to GV-VMS / DVR / NVR......................................ii
Note for Installing Camera Outdoor....................................................iii
1. Introduction ....................................................................................1
1.1 Packing List ........................................................................................................... 1
1.2 Optional Accessories ............................................................................................. 2
1.3 Overview................................................................................................................ 2
2. Installation ......................................................................................4
3. Waterproofing the Cable ................................................................7
4. Accessing the Camera ...................................................................9
4.1 Web Browser ......................................................................................................... 9
4.2 Looking Up the Dynamic IP Address.....................................................................10
4.3 Configuring the IP Address ...................................................................................12
5. The WebInterface.........................................................................13
6. Upgrading System Firmware .......................................................15
7. Restoring to Factory Default........................................................16

ii
Note for Connecting to GV-VMS / DVR / NVR
The H.265 Target Eyeball Dome is designed to work with GV-VMS / DVR / NVR, a video
management system. Once the camera is connected to the GV-VMS / DVR / NVR, the
resolution set on the GV-VMS / DVR / NVR will override the resolution set on the camera’s
Web interface. You can only change the resolution settings through the Web interface when
the connection to the GV-VMS / DVR / NVR is interrupted.

iii
Note for Installing Camera Outdoor
When installing the camera outdoor, be sure that:
1. The camera is set up above the junction box to prevent water from entering the camera
along the cables.
2. Any power, audio and I/O cables are waterproofed using waterproof silicon rubber or the
like.
3. The screws are tightened and the cover is in place after opening the camera cover.

Introduction
1
1
1. Introduction
Welcome to the GV-EBD4700 IR Eyeball IP Dome Quick Start Guide. In the following
sections, you will learn the basic installations and configurations. For a detailed user manual,
see the GV-EBD4700 IR Eyeball IP Dome User’s Manual.
1.1 Packing List
H.265 Target Eyeball Dome
Screw x 3
Screw Anchor x 3
Waterproof Rubber Set
Drill Template Paster
Software Download Guide
Warranty Card

2
1.2 Optional Accessories
Optional accessories can expand the capabilities and versatility of your GV-EBD4700.
Contact your dealer for more information.
Model Number Name Details
GV-Mount211 Wall Mount Bracket
Dimensions: 233 x 126 x 126
mm (9.2” x 5” x 5”)
Weight: 0.92 kg (2.0 lb)
GV-PA191 Power over Ethernet
(PoE) Adapter
The GV-PA191 is a Power over
Ethernet (PoE) adapter
designed to provide power to
the IP device through a single
Ethernet cable.
GV-POE Switch The GV-POE Switch is designed to provide power along
with network connection for IP devices. The GV-POE
Switch is available in various models with different
numbers and types of ports.
Power Adapter Contact your sales representative for the countries and
areas supported.

Introduction
3
1
1.3 Overview
No. Description
1 Bottom ring
2 Housing
3 Lens
4 Infrared indicator
5 Power connector (DC 12 V)
An optional power adapter is required.
6 Ethernet connector / PoE

4
2. Installation
The Target Eyeball Dome is designed for outdoors. With the standard package, you can install
the camera on the ceiling. Or you can purchase optional mounting accessories to mount
GV-EBD4700 on a wall.
Below are the instructions for Ceiling Mount. There are two kinds of Ceiling Mount:
Concealed Installation and Open Installation. In Concealed Installation, the cables are
hidden in the ceiling. In Open Installation, the cables are led out from the open slot on the
bottom ring.
For Concealed Installation
1. Stick the drill template paster to the ceiling, and then drill three holes according to the drill
template.
2. Insert the screw anchors.


Installation
5
2
3. Remove the bottom ring by turning it anticlockwise.
4. Connect the cables and then secure the camera.
5. Adjust the monitoring direction.

6
6. Mount the bottom ring.
For Open Installation
Lead the cables out from the open slot on the bottom ring before screwing the camera to the
ceiling as shown in step 4 in For Concealed Installation.

Note: You can optionally purchase GV-Mount211 for Wall Bracket Mount. For details, see
GV-EBD4700 IR Eyeball IP Dome User’s Manual.

Connecting the Camera
7
3
3. Waterproofing the Cable
Waterproof the Ethernet cable by using the supplied waterproof rubber set.
1. Attach the seal ring to the RJ-45 plug.
Sealring
2. Insert the waterproof components through the Ethernet cable as shown below.
32
Insertinorder
3. Insert the cylindrical waterproof ring into waterproof bolt.
Cylindricalwaterproofring
Water
p
roofbolt

8
4. Insert the cable into the RJ-45 plug and screw the waterproof bolt in.
5. Screw in the waterproof bolt lid.
Bolt lid
6. Finish the waterproof Installation.

Accessing the Camera
9
4
4. Accessing the Camera
4.1 System Requirements
Once installed, your camera is accessible over the network. Make sure your PC has good
network connection, and meet the following requirement:
CPU Intel Core i5-4670, 3.40 GHz
Memory DDR3 8 GB RAM
On Board Graphics Intel HD Graphics 4600 (Versions of driver from year 2014 or later
required)
Web Browsers Internet Explorer 11.0 or above
Mozilla Firefox
Safari
Note: Some functions are not available on non-IE browsers.

10
4.2 Looking Up the Dynamic IP Address
By default, when the camera is connected to LAN with a DHCP server, it is automatically
assigned with a dynamic IP address. Follow the steps below to look up its IP address.
Note: The computer you use to configure the IP address must be under the same LAN with
your camera.
1. Download and install the GV-IP Device Utility program from
http://www.geovision.com.tw/english/5_8.asp
2. On the GV-IP Utility window, click the button to search for the IP devices connected in
the same LAN. Click the Name or Mac Address column to sort.
3. Find the camera with its Mac Address, click on its IP address and select Web Page.

Accessing the Camera
11
4
4. The login page appears.
5. For the first time accessing the Web interface, download and install the plug-in.
6. Type the default ID and password admin and click Apply to log in.

12
4.3 Configuring the IP Address
If the camera is connected to LAN without a DHCP server, the default IP address will be
192.168.0.10. Follow the steps below to modify the IP address to avoid IP conflict with other
GV-IP devices on the same LAN.
1. Open your web browser, and type the default IP address http://192.168.0.10.
2. In both Login and Password fields, type the default value admin. Click Apply.
3. Click Setup, select Network in the left menu and select TCP/IP.
4. Select Static IP from the IP Obtain Mode drop-down list.
5. Enter the IP address, subnet mask, and default gateway address. Make sure that the IP
address of the camera is unique in the network.
6. Click Save.

Upgrading System Firmware
13
6
5. The Web Interface
Once you log in the Web interface, you will see the live view as shown below.
No. Name Function
1 Proportional
Set the display ratio of the image.
Scale: display images by 16:9.
Stretch:display images by window size.
Original: display images in its original size.
2 Live Stream Select a live video stream: main stream, sub stream or third
stream.
3 Image Open the image setting page.
4 Full Screen Mode Display in full screen mode.
5 Play/Stop Play or stop live video.
6 Snapshot Take a snapshot of the current image displayed on the PC.
7 Local Recording Start or stop local recording.
8 Digital Zoom Start or stop digital zoom.

14
9 Reset the packet loss rate to zero.
10 Display packet loss rate and bit rate information in the bottom.
Note:
1. The paths for saving snapshots and local recordings are set in System Configuration.
2. The buttons (No. 9 and No. 10) will appear on the floating toolbar after you move the
mouse cursor on a live view window.
3. Click the button (No. 10) to display the bottom information. Click this button again, the
bottom information is displayed if the mouse cursor is moved on a live view window or
on the bottom information, and it hides automatically if the mouse cursor remains on a
live view window for 3 seconds or leaves the window.

Upgrading System Firmware
15
6
6. Upgrading System Firmware
GeoVision periodically releases the updated firmware on the website. To load the new
firmware into the camera, follow the instructions below.
1. At the top of the Web interface, click Setup.
2. In the left menu, select System and select Maintenance. This page appears.
3. Click the Browse button to locate the firmware file (.zip) saved at your local computer.
4. Click the Upgrade button to process the upgrade.