GeoVision GV-VD8700 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual forfuture use. VD8700V10-QG-A
Quick Start Guide
GV-VD8700 IR Vandal Proof IP Dome

© 2018 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
March, 2018

Contents
Note for Connecting to GV-VMS / DVR / NVR......................................ii
Note for Recording...............................................................................iii
Note for Installing Camera Outdoor....................................................iv
1. Introduction.....................................................................................1
1.1 Packing List ............................................................................................................1
1.2 Optional Accessories ..............................................................................................2
1.3 Overview ................................................................................................................3
1.4 Installation Flowchart ..............................................................................................5
2. Installation.......................................................................................6
3. Connecting the Camera................................................................15
3.1 I/O Connector .......................................................................................................16
4. Accessing the Camera .................................................................17
4.1 System Requirements ..........................................................................................17
4.2 Looking Up the Dynamic IP Address.....................................................................17
5. Setting up for Face Recognition..................................................19
5.1 Ideal Camera Position ..........................................................................................19
5.2 Adjusting Illumination............................................................................................22
5.3 Enrolling Face Data ..............................................................................................23
5.3.1 Photo Requirements .................................................................................26
6. Upgrading System Firmware .......................................................27
7. Restoring to Factory Default........................................................28
7.1 Using the Web Interface .......................................................................................28
7.2 Directly on the Camera .........................................................................................28
i

Note for Connecting to GV-VMS / DVR / NVR
The camera is designed to work with and record on GV-DVR / NVR / VMS, a video
management system.
Once the camera is connected to the GV-DVR / NVR / VMS, the resolution set on the
GV-DVR / NVR / VMS will override the resolution set on the camera’s Web interface.
You can only change the resolution settings through the Web interface when the
connection to the GV-DVR / NVR / VMS is interrupted.
ii

Note for Recording
1. By default, the recording function is disabled. Configure the function in the
camera’s Web interface to record alarm events to the memory card inserted in the
camera upon disconnection from GV-DVR / NVR / VMS. See 4.4.3 Tools,
GV-VD8700 IR Vandal Proof IP Dome User’s Manual for details.
2. Mind the following when using a memory card for recording:
Recorded data on the memory card can be damaged or lost if the data are
accessed while the camera is under physical shock, power interruption,
memory card detachment or when the memory card reaches the end of its
lifespan. No guarantee is provided for such causes.
The stored data can be lost if the memory card is not accessed for a long
period of time. Back up your data periodically if you seldom access the
memory card.
Memory cards are expendable and their durability varies according to the
conditions of the installed site and how they are used. Back up your data
regularly and replace the memory card annually.
Replace the memory card when its read/write speed is lower than 6 MB/s or
when the memory card is frequently undetected by the camera.
To avoid power outage, it is highly recommended to apply a battery backup
(UPS).
3. For better performance, it is highly recommended to use memory cards of the
following specifications:
Micro SD card of MLC NAND flash, Class 10.
iii

iv
Note for Installing Camera Outdoor
When installing the camera, be sure that:
1. The camera is set up above the junction box to prevent water from entering the
camera along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon
rubber or the like.
3. The screws are tightened and the cover is in place after opening the camera
cover.

1. Introduction
Welcome to the GV-VD8700 IR Vandal Proof IP Dome Quick Start Guide. In the
following sections, you will learn the basic installations and configurations. For a
detailed user manual, see the GV-VD8700 IR Vandal Proof IP Dome User’s Manual:
http://www.geovision.com.tw/download/product/.
1.1 Packing List
H.265 Vandal Proof Dome
Screw x 4
Screw Anchor x 4
Audio Wire x 2
I/O Cable
RJ-45 Connector
Installation Sticker
Waterproof Rubber Sets (for RJ-45
Cat.5 and DC12V / for RJ-45 Cat. 6)
PG21 Conduit Connector
Torx Wrench
Big Concave Hexagon Wrench
Small Concave Hexagon Wrench
Silica Gel Bag
Sticker (for Silica Gel Bag)
Conduit Converter
Ruler
Download Guide
Warranty Card
1

Introduction
1
1.2 Optional Accessories
Optional devices can expand your camera’s capabilities and versatility. Contact our
sales representatives for more information.
Name Details
GV-Mount Accessories The GV-Mount Accessories provides a comprehensive
lineup of accessories for installing the camera on
ceiling, wall corner and pole. For details, see GV-Mount
Accessories Installation Guide.
GV-PA901
Power over Ethernet
(PoE) Adapter
The GV-PA901 is a Power over Ethernet (PoE) adapter
designed to provide power to the IP device through a
single Ethernet cable.
GV-PoE Switch The GV-PoE Switch is designed to provide power along
with network connection for IP devices. The GV-PoE
Switch is available in various models with different
numbers and types of ports.
GV-Relay V2 The GV-Relay V2 is designed to expand the voltage
load of GV IP devices. It provides 4 relay outputs, and
each can be set as normally open (NO) or normally
closed (NC) independently as per your requirement.
Metal PG21 Conduit
Connector
The metal PG21 conduit connector allows you to run the
wires through a 3/4” conduit pipe.
Power Adapter Contact our sales representatives for the countries and
areas supported.
2

1.3 Overview
12 3 45
7
912
8
14
10 11 13
6
15
3

Introduction
1
No. Name Description
1 LED Indicators
The power LED (top) turns on when the power is
on and turns off when there is no power supply.
The status LED (bottom) turns on when the
system operates normally and turns off when an
error occurs.
2 Audio Out Currently not functional.
3 Line In
Connects to a microphone for audio input.
Note: This interface only works with an external
microphone with powered supply.
4 LAN / PoE Connects to a 10/100 Ethernet or PoE.
5 DC 12V Connects to power.
6 Rotational Screw Loosens to rotate the camera.
7 Conduit Connector Waterproofs the Ethernet cable.
8 Default Button
Resets the camera to factory default settings. For
details, see Chapter 7 Restoring to Factory
Default Setting.
9 Focus Screw Adjusts the focus of the camera.
10 Zoom Screw Zoom the camera in or out.
11 Tilt Screw Loosens the screw to tilt the camera.
12 I/O Connector Connects to I/O devices.
13 Built-in Microphone
Connectors
Connects to a built-in microphone. For details, see
Chapter 3 Connecting the Camera.
14 Conduit Connector Waterproofs the audio / I/O wires.
15 Memory Card Slot Inserts a micro-SD card (SD/SDHC/SDXC/UHSI,
Class 10) to store recording data.
4

5
1.4 Installation Flowchart
See the flowchart for a clear idea of the installation process before proceeding to
Chapter 2 Installation. Refer to the relevant sections in GV-VD8700 IR Vandal Proof
IP Dome User’s Manual if needed.
5.3 Ideal Camera Position
1.4 Installing the Camera
5.4 Adjusting Illumination
Install the camera at the ideal camera posion
Adjust Illumination of the installation site
Chapter 2 Getting Started
Access the camera
5.5 Enrolling Face Data
5.5.1 Photo Requirements
Enroll Face Data
5.6.1 Settings
Activate Face Recognition
5.6.4 Events
Searching Face Recognition Results

2. Installation
The camera is designed for outdoors. With the standard package, you can install the
camera on the ceiling.
Note:
1. An improper installation location can affect face recognition results. For optimal face
recognition results, follow the recommended guidelines to install the camera. For
details, see 5.1 Ideal Camera Position.
2. You can also install the camera on ceilings, wall corners (concave or convex), and
poles. For details on these installations, see GV-Mount Accessories Installation
Guide.
3. You need to format the memory card before using it for the first time. For details, see
4.4.4 External Storage Settings, GV-VD8700 IR Vandal Proof IP Dome User’s
Manual.
1. Remove the housing cover with the supplied torx wrench.
6

2. Optionally remove the cables that attach the built-in microphone to the camera to
assist with installation.
Cables for built-in microphone
3. Remove the back plate with the supplied torx wrench and remove the safety lock
with a Philips screwdriver. Keep the removed screw for later use.
Safety loc
k
4. Thread wires into the camera.
A. Rotate to remove the cap of the conduit connector.
7

Installation
2
B. Unplug the conduit connector inside the housing and disintegrate the
connector. You should have 3 parts:
C. Thread the audio wires and I/O wires through the conduit entry and then
through parts 1, 2, and 3 of the conduit connector.
Tip:
1. To make the threading easier, it is recommended to thread the wires in the
order described in Step 4-C.
2. Use a pair of pliers to help you pull the wires through the camera.
If you use cat 5 Ethernet cable, there are 5 holes each labeled with its diameter. Remove
the plugs and push the wires to the corresponding hole listed below:
Plug
3.2 mm: Audio
1.9 mm: DIDO
8

IMPORTANT:
1. Use the supplied ruler and leave at least 14 cm of I/O wires and 10 cm of audio
wires between their connectors on the camera and the conduit connector.
2. The plugs are used to prevent water from entering the camera housing. Keep
the unused holes plugged and save the removed plugs for future use.
3. Only thread the wires through their designated holes on the conduit connector
to make sure the wires are properly sealed.
If you use cat 6 Ethernet cable, thread the DC 12V wires through the conduit connector.
Refer to the following for the corresponding holes and their diameters.
3.2 mm: Audio
1.9 mm: DIDO
1.9mm: DC 12V
IMPORTANT: Leave more than 10 cm of power wires between their connectors
on the camera and the conduit connector.
9

Installation
2
5. Install the Ethernet cable.
A. Rotate to remove the indicated cap and the plug inside.
B. Thread an Ethernet cable (the end with no RJ-45 connector) and the optional
power adapter wires from the back panel through the conduit connector.
IMPORTANT: Use the supplied ruler and leave about 14 cm of the Ethernet cable
between the connector on the camera and the conduit connector.
C. Re-install the cap. Make sure the cap is installed tightly to waterproof the
camera.
10

6. Connect the wires to the camera and insert the memory card to the memory card
slot. For details, see 1.3 Overview and Chapter 3 Connecting the Camera.
Tip: Unscrew the indicated screws and lift the camera to help you connect the
wires and insert the memory card.
7. Sort out the wires at the back. You can have the wires come out from positions A
and B or from C.
AB
C
11

Installation
2
8. Secure the back plate to the ceiling.
A. Paste the sticker to the ceiling. The arrow on the sticker indicates the
direction that the camera faces.
B. Drill 4 holes for screws. The recommended ones are indicated as ‘1’.
C. Insert the screw anchors to the 4 holes.
D. Drill holes A & B or only hole C for sorting out the wires according to the
figure in Step 7.
E. Secure the back plate to the ceiling with the supplied screws.
12

9. Secure the camera to the desired location.
A. Secure the safety lock to the camera with the screw you removed from the
back plate in Step 2.
Safety lock
B. Thread all the wires into the ceiling and connect them.
C. Secure the camera to the back plate with the torx wrench.
10. Access the live view. See Chapter 4 Accessing the Camera.
11. Adjust the angle, focus and zoom of the camera.
Pan Adjustment
Tilt Adjustment
Rotational Adjustment
13

Installation
14
2
Zoom Adjustment
Loosen the screw
Focus Adjustment
Loosen the screw
12. Replace the silica gel bag, organize the wires and secure the camera cover with
the torx wrench.
Organize
the wires
to avoid
blocking
the lens