Fike Fik-w-pull-da User manual

BEFORE INSTALLING

This pull station must be installed in compliance with the control panel sys-

tem installation manual, the SWIFT Wireless Gateway Manual, applicable

NFPA standards, national and local Fire codes and the requirements of the

AHJ (Authority Having Jurisdiction). Regular testing of the devices should be

done in accordance with the appropriate NFPA standards. Pull stations offer

maximum performance when installed in compliance with the National Fire

Protection Association (NFPA); see NFPA 72.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The FIK-W-PULL-DA wireless, addressable pull station is a UL38-compliant

dual-action manual pull station with a key-lock reset feature intended for

use with a wireless gateway or wireless fire alarm control panel (FACP). (See

Figure 1.) It provides Fike panels one addressable alarm initiating input. The

device communicates through a robust, bi-directional mesh network to the

gateway and/or FACP. Rotary dial switches are provided for setting the pull

station’s address. (See Figure 2.) Operating instructions are molded into the

pull station handle along with Braille text. The wireless pull station meets

the Americans with Disabilities Act Accessibility Guidelines (ADAAG) controls

and operating mechanisms guidelines (section 4.1.3[13]), the Americans with

Disabilities Act (ADA) requirement for a 5 lb. maximum pull force to activate

the pull station and conforms to ANSI/UL Standard 38.

Panels offer different feature sets across the various models. As a result, cer-

tain features may be available on some control panels, but not on others. The

possible feature sets available with the wireless pull station include:

• An LED on the wireless pull station is controlled by the panel to indicate

device status. Operational modes include red, green and amber colors in

various solid or blink patterns.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Fike system control panel (list available from Fike).

FIGURE 1. WIRELESS MANUAL PULL STATION

C2039-00

BATTERY DOOR

The battery door includes a magnet for activation and tamper resistance. (See

Figure 2.) The battery door magnet activates communication to the panel,

therefore, the battery door must be installed and closed for the pull station

to work properly. The magnet also activates a tamper fault at the panel if the

battery door is opened. Do NOT remove this magnet.

BATTERY REPLACEMENT

Low battery levels on the wireless devices are displayed as a trouble in the

FACP. Therefore when the message “TROUBLE BATTERY LOW” is displayed,

replace the battery in the device. This message is an indication that approxi-

mately one week of battery life remains.

To replace the batteries in a wireless device use the following steps:

1. Have 4 CR123A (or DL123A) batteries available.

2. Use the key to unlock and open the pull station door.

3. Open the battery compartment. (See Figure 2.)

4. Remove the used batteries and replace with new batteries. Batteries can

be inserted directly into the pull station or inserted as a set of 4 batteries

pre-loaded in a battery cartridge available from Fike. (See Figure 2.) The

battery compartment and cartridge indicate the correct orientation of the

batteries. Carefully align the batteries with these markings, and do not force

them into place.

5. Close the battery compartment cover.

6. Close and lock the pull station door.

FIGURE 2. BATTERY INSTALLATION

Rotary Address Switches

Battery Compartment With Door Open

Battery Compartment Door in the Open (Down) Position

Battery

Magnet

Location

Battery Compartment Door in the Closed (Up) Position

C2041-00

Battery Cartridge

C2030-00

SPECIFICATIONS

Maximum Operating Voltage: 3.3 VDC

Maximum Current Draw: 5.0 mA (LED on)

Average Operating Current: 210 µA

Maximum Transmit RF Power: 17 dBm

Radio Frequency Range: 902-928 MHz

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Battery Type: 4 Panasonic CR123A or 4 Duracell DL123A

Battery Life: 2 year minimum

Battery Replacement: Upon TROUBLE BATTERY LOW display and/or during annual maintenance

Dimensions: 5.6" (142 mm) H x 4.2" (107 mm) W x 2.1" (53 mm) D

Accessories: Battery Cartridge W-BATCART

I56-6964-001

INSTALLATION AND MAINTENANCE INSTRUCTIONS

704 SW 10th Street

Blue Springs, MO 64015

Phone: 816.229.3405; Fax: 816.228.9277

www.ﬁke.com

FIK-W-PULL-DA Wireless Pull Station

http://www.fike.com/06-912

r system/product documentation including

installation, operation, and maintenance,

scan QR code or enter URL provided.

1 I56-6964-001

10/5/2021

OPERATION

To activate the dual-action pull station:

Push in and pull down on the handle. The word ‘ACTIVATED’ appears after

the handle is pulled down. This will remain until the pull station is reset.

To reset the pull station:

1. Insert the key into the lock and rotate ¼ turn counterclockwise.

2. Open the door until the handle returns to normal.

3. Close and lock the door.

NOTE: Closing the door automatically resets the switch to the ‘Normal’ posi-

tion. Opening the door will not activate or deactivate the alarm switch.

SPACING

Wireless technologies can exhibit communication disruption if devices are

spaced too close together. To avoid this form of disruption, SWIFT® devices

should not be placed closer than 2 feet (60 cm) apart without an intervening

structure. For specific information regarding pull station placement refer to

NFPA 72, ADAAG, and ADA.

MOUNTING

To mount the wireless pull station, attach the wireless pull station mounting

plate to a permanent structure. The mounting plate can be surface mounted.

To avoid interference with the wireless network metal electrical boxes are NOT

recommended. Do not detach the door of the pull station during installation.

The door of the pull station cannot be reattached to the main housing after the

pull station has been installed. Place the pull station onto the mounting plate

and secure by tightening all three (3) mounting screws inside the door of the

product housing using a #1 Phillips head screwdriver. (See Figure 3.)

NOTE: Do not attach the pull station to temporary structures such that the

placement could be altered.

FIGURE 3. DEVICE MOUNTING

Mounting

Screws

Mounting

Plate

C2020-00

LICENSING STATEMENT

Use of these products in combination with non-Honeywell products in a wireless mesh network, or to access, monitor or control devices in a wireless mesh nework via the internet

or another external wide area network, may require a separate license from Sipco, LLC. For more information, contact Sipco, LLC or Ipco, LLC at 8215 Roswell Rd., Building 900,