GEV CAS 88313 User manual

Typ: CAS
# 088313
GEV_2_fam_RZ_luensee_print.indd 1 06.06.14 10:56

Abb./Fig. 1
Abb./Fig. 2a Abb./Fig. 2b
Abb./Fig. 4Abb./Fig. 3
2
GEV_2_fam_RZ_luensee_print.indd 2 06.06.14 10:56

Abb./Fig. 5
Abb./Fig. 6
* Optional
3
GEV_2_fam_RZ_luensee_print.indd 3 06.06.14 10:56

2-House Audio Door Entry System (2-Wire Installation)
In this Set (Fig. 1)
1. Power Adapter
2. 2x Handset
3. Outdoor Panel
4. Rain Cover
Components/ operating controls
Handset (Fig. 2a)
1. Loudspeaker
2. Microphone
3. Ring tone volume adjustment
4. Intercom button
5. Strike control (Door/Gate opener)
6. Terminal block
Outdoor panel (Fig. 2b)
1. Loudspeaker
2. Name plate/bell
3. Screws
4. Microphone
5. Cable duct channel
6. Holes for attaching the unit to the wall
7. Terminal block
8. Switch for setting the sound level for
the speaker of the outdoor panel
9. Switch for setting the sound level for
the speaker of the handset
Introdcution
This audio door phone system consist of
two handsets and an outdoor unit. With
these you can establish an audio connec-
tion between the caller and yourself. Fur-
thermore you have the option to add a door/
gate strike (not included) into the system.
This audio door phone set uses a BUS-type
protocol; i. e. just two wires are needed for
all functions (ringing, speaking, listening,
controlling the door/ gate strike).
Safety instructions
All warranty claims will be null and void in
the event of any damage or loss caused by
failure to observe these operating instruc-
tions. We accept no liability for any conse-
quential losses or damage. We accept no
liability for
any personal injury or material da-
mage caused
by improper use or by failure
to observe the safety advice. In these cases
the guarantee and warranty are invalidated.
For safety and authorization purposes it is
not permitted to carry out any adaptation or
conversion of the device.
1. Do not disassemble the unit.
2. Do not spray water on the indoor unit.
Do not keep the outdoor unit where it
will be exposed to extreme moisture.
3. Do not drop or shock the unit.
4. Remove the power cord from the wall
socket when unit is not used for long
periods.
5. This apparatus is designed for moderate
climates. Do not use in high humidity,
dusty or dirty areas.
Installing
Attention: if you like to test the units before
final installation then don’t do this with both
units inside. The same room-this could lead
to a Larsen-eect (an annoying acoustic
feedback of the indoor panel).
Installation of the outdoor panel (Fig. 3)
The outdoor panel is determined for wall-
mounting.
Remove the front panel of the outdoor unit
by loosening the two screws on the bot-
tom (Fig. 3/1). Run the cables coming from
the indoor unit (handset) through the cable
opening (Fig. 3/ 2). Likewise, if required, the
cables coming from the electric door/gate
opener, too. Screw the rain cover housing
with two screws at the location you provided.
(Fig.3/ 3). Now you can connect the wires
according to the wiring diagram (depending
on the number of indoor units see Figure 5
or 6) to the appropriate terminals (Fig. 3/4).
Before closing the front plate again, you can
do still volume settings on the fixed back
plate (Fig. 2b/8 and 9). Use a small, suitable
screwdriver and turn the screw without
much force (Fig 2b/8 volume control of the
outdoor
unit. Fig 2b/9 volume control of the
8
GEV_2_fam_RZ_luensee_print.indd 8 06.06.14 10:56

indoor unit).
Tip: Seal the joints between the outdoor unit
and the wall from three sides with silicone.
Let the joint on the bottom open to decrease
the likelihood of condensation.
Mounting the indoor unit (Fig. 4a and 4b)
First, open the indoor unit for this purpose,
go with a suitable screw driver on the right
bottom in the recess and pry through slight
leverage the top of the lower shell. Mount
the lower shell with four screws at the desi-
gnated place on the wall. Now connect the
wires as shown in figure 5. or 6-depending
on your desired level of expansion.
Installation of the handset/
installation of outdoor panel/
caption of the badge
Connecting the handset.
See figures 5 or 6-depending on your desired
level of expansion. To avoid problems high-
and low-voltage cables should never be in
the same cable conduit. Connect the cables
as shown in the figures described.
Connecting the handset to the outdoor
panel: Connect the power supply with the
inside socket. Connect „L +“ and „L -“ of the
handset with the terminals „L +“ and „L -“ of
the outdoor panel.
Connecting an electric door/or gate strike.
You can optionally include an electric door
and/or gate opener in this system. For the
connection diagram see Figure 5 or 6.
Caption of the name plate: Remove the
cover of the bell in which you lever it by
using a thin tool and carefully push it inside
the notches (fig. 7/A).
Set Up/Operation
Pressing on the push button of the outdoor
panel, raises a signal on the handset (max. 6
times within 30 sec.). You can now pick up
the phone and speak with the guest for a
maximum of approx. 90 sec. To operate the
electric door opener, briefly press (1 sec.)
the button on the indoor unit. Important:
It is essential that you use a door opener
which has a memory function. Regarding
the connection instructions see connection
diagram 5 or 6. As a suitable electric door
opener, we
recommend such as item no.
007680 (110 mm) or 007697 (250 mm) from
our GEV product range.
For connecting an electric gate opener
connect the terminals „GATE“ „GATE“ of the
outdoor panel and the two corresponding
terminals (varies- depending on the manuf-
acturer. Consult the manual of your gate
drive engine) to your gate engine (terminals
„GATE“ „GATE“ are dry contacts).
In case you have connected an external gate
drive, enable this by a three-second press
on the button on the phone.
Important: The functions can be exe-
cuted only when the active unit and
after lifting the handset.
Additional information
You have the option to connect up to
three additional interior handsets in parallel
Abb./Fig. 7
A
GB
9
GEV_2_fam_RZ_luensee_print.indd 9 06.06.14 10:56

(Fig. 6/order no. 8830601). When connec-
ting multiple handsets, it is sucient if you
are using a single power supply for all stati-
ons. However, this power supply has to be
the one which is the closest to the outdoor
panel. In order to communicate internally,
press the button. This will trigger a
collective call and establish a connection to
the remote handset which is being picked up
first (for approx. 30 sec.). As long as there’s
an internal connection, the voice contact to
the outdoor panel is locked. The intercom
function is interrupted in case there is an ex-
ternal call coming in.
Receycling instructions
This device may not be disposed
of with unsorted household waste.
Owners of old devices are required by
law to dispose this device correctly.
Contact your twon council for further infor-
mation.
Specifications
Handset (8830601) Specifications
Dimensions 70[W] x 230[H] x 40 [D]mm
Power Supply DC18V / 1,5A
Power Consumption Max. 2W
Connection System 2-wires
Sounds 1
Max. Distance/ wire to be used Min. diameter of cable between last
handset and outdoor panel
up to 25m: ø 0,6mm-1,0mm
up to 100m: ø 1,0mm-1.5mm
Protection type IP 20
Mains adapter Specifications
Power Supply 230 V~, DC 18V, 1,5A
Outdoor panel (8831301) Specifcations
Dimensions 95[W] x120[H] x 30 [D]mm
Current DC12V (via indoor unit / handset)
Installation type Outdoor- / Indoor unit : 2-wires
Door strike Current 12V DC / max. 1.0A
Gate motor Dry contact / closing time ca. 3 sec.
Type of installation Wall mount
Protection type IP 54
Operating temperature -10 ˚C - 45 ˚C
10
Technical and design features may be subject to change without notice.
GEV_2_fam_RZ_luensee_print.indd 10 06.06.14 10:56

GB
11
GEV_2_fam_RZ_luensee_print.indd 11 06.06.14 10:56

Gutkes GmbH
Rehkamp 13
30853 Langenhagen
Germany
www.gev.de
[email protected]
Hotline: [phone]
Max. 14 Ct./Min. aus dem deutschen Festnetz.
Mobil max. 42 Ct./Min.
International calls may vary.
06/2014
GEV_2_fam_RZ_luensee_print.indd 12 06.06.14 10:56