GEV CVS 88351 User manual
Typ: CVS
# 088351
MA_2fam_Video_88351_print.indd 1 11.06.14 08:03
Safety Instructions
All warranty claims will be null and void in
the event of any damage or loss caused
by failure to observe these operating
instructions. We accept no liability for any
consequential losses or damage. We accept no
liability for any personal injury or material damage
caused by improper use or by failure to observe
the safety advice. In these cases the guarantee and
warranty are invalidated. For safety and authorization
purposes it is not permitted to carry out any adaptation
or conversion of the device
1. Do not disassemble the unit.
2. Do not spray water on the indoor unit. Do not keep
the outdoor unit where it will be exposed to extreme
moisture.
3. Do not drop or shock the unit.
4. Remove the power cord from the wall socket when
unit is not used for long periods.
5. Do not cover the ventilation holes
6. This apparatus is designed for moderate climates.
Do not use in high humidity, dusty or dirty areas.
Warnings
1. Do not install the outdoor unit where it will be
exposed to direct sunlight. Do not install the outdoor
unit where it will be subjected to extremes of dust or
moisture. Do not install the outdoor unit where it will
be exposed to rain. Do not install the outdoor unit in a
location where the lens filter is likely to get scratched
or very dusty.
Assembly instructions
WIRING DIAGRAM 2 Monitors and
1 Outdoor Station
DIP Setting
MASTER
DIP Setting
MASTER
Before you start
Check the pack and make sure you have all of the
part listed below. If not, contact your local store who
will be able to help you.
This video door phone is composed of two monitors
with its modular adapter and a roadside panel. It
allows communicating with the visitor who calls at the
door and controlling the opening of the door and/or
gate. You can develop your own installation by adding
an optional additional monitor and/or a second
roadside panel. For a safe installation and use, please
read carefully these instructions and keep them safe.
Parts
1 Indoor monitor
1 Outdoor station
1 Wall mounting bracket
1 Power adaptor
6 Screw/ Wall plug
4 Accessory connector
Indoor unit
1
10
6789
2345
11
1 Monitor screen
2 Talk on/talk o (monitor o) and intercom
(monitor standby mode)
3 Door open
4 Camera 1/camera 2 (with optional 2 nd monitor)
5 Intercom
6 Menu select (brightness, contrast, color)
7 Down
8 Up
9 Microphone
10Ring sound volume
11Power in
Outdoor unit
1
2
3
4
4
5
5
6
1 Camera lens
2 White LEDs for night vision
3 Speaker
4 Name plate
5 Call button
6 Microphone
6
2 Apartment Video Door Entry System CVS 88351 (4-Wire installation)
MA_2fam_Video_88351_print.indd 6 11.06.14 08:03
Installation of indoor monitor
1 2 3
1. Fix the wall mounting bracket in the best place by
using 4 screws and plugs (fig. 1). Wire the monitor
as described in the diagram and connect the power
supply.
2. Carefully place the indoor monitor against the
bracket and gently push down the monitor so that
the pins on the bracket engage in the slots on the
rear of the monitor (fig. 2). Hold tight the monitor until
the installation is finished.
3. Secure the assembly with the 2 screws from
underneath (fig. 3).
Only after having connected the roadside
panel, connect the 230 V~ power supply to
the adapter.
Installation of the outdoor device
A B
DC
1. Remove the front panel (fig. B). In the first loosen
the two screws on the bottom (fig. A). 2. Attach the
external station to the intended location on the wall
using wall plugs and screws (fig. C). Connect the
outdoor unit to the cables brought forward. At this
point, you have the possibility to adjust the camera’s
module angle slightly manually. Aim the camera in
the desired position. 3. Screw the front panel again
(fig. D).
Important: do not point the video camera
directly at the sun or at reflecting surfaces.
Tip: we recommend passing the cables through a
protective sleeve to shield them from impacts and
Optional:
WIRING DIAGRAM 4 Monitors and
1 Outdoor stations
DIP Setting
MASTER
DIP Setting
SLAVE
DIP Setting
MASTER
DIP Setting
SLAVE
Cable connection
Connect the monitor to the camera and the door
opener with the cables according to the wiring
diagram.
Carefully insert the wires to the terminal by pressing
down the terminal flap with any small tool taking care
that the 2 bare wires do not touch.
Make absolutely sure that no bare wires are touching
each other after the connection!
Installation height
Recommended installation height is approximately
140 cm for monitor unit and 150 cm for outdoor
camera.
140 cm
150 cm
40°
70°
Tip: please make sure you found the optimal
installation height prior to having fixed the outdoor
unit to the wall.
7
GB
MA_2fam_Video_88351_print.indd 7 11.06.14 08:03
environmental influences.
Adding the name to the nameplate
A
Remove the cover of the doorbell button by loosening
the notches below the cover (fig. A).
Optional installation of a transformer
instead of a power adaptor
Alternatively you may use a transformer to supply the
video door entry system with electricity (GEV order
no. 8835102).
Performance Settings
While the monitor is switched on you can adjust the
brightness, contrast and color of the monitor in which
you press the „settings/confirmation“ button. (6). If
you press this button (see above) the menu appears
on the monitor. By pressing the „up“/„down“ buttons
(7, 8) you can scroll through the menu. Select the
submenu and confirm by pressing the setting button
(6). Once you are in the submenu scroll through it by
using the „up/down“ (7, 8) buttons, too, to choose the
appropriate settings for you. Confirm this again by
pressing the „confirm button“ (6).
Operating Instructions
Important: the touch keys must be handled by slightly
touching with the fingers.
1. Activation of units
When the call button on the outside camera unit is
pressed, the indoor unit chime rings and the visitor’s
picture will appear on the indoor monitor. After the
visitor is visually identified, and you wish to talk with
the visitor, touch the button. The unit will remain
activated for approximately 60 seconds before it
automatically shuts o. To re-activate for continued
conversation, touch the button and then touch the
button.
Should you not react on an incoming signal, the
monitor will go in stand-by after approx. 30 seconds
2. Activation of outside unit from monitor unit.
a) Touch the button of the indoor unit at any time
and the outdoor camera will be activated and show
the outside view.
b) If you have installed two cameras, touch this button
to change from camera one to another.
3. Activation of “Intercom” button
An intercom calling can be started by any indoor
monitor.
When the intercom button on one indoor monitor
is touched, this will ring all monitors in a system,you
can talk with the one calling monitor by touching the
intercom button on the second monitor, touch for
8
shutting o. There is approximately 60 seconds of
time before the unit automatically shuts o.
4. Door opener button
In case you have attached an electrical lock or a
door strike is added to the installation (operation via
a separate transformer), connect it to the terminals at
the back of the roadside panel. If you want to open
the door to let the caller in, just touch the button
on the indoor monitor. This function can only be used
when the screen is switched on. It is normal that the
image switches o one moment following the control
of the door opener.
Important: it is essential that the electric latch or
lock installed has a mechanical memory. We therefor
recommend GEV’s door openers 007680 or 007697
in combination with the GEV bell transformer (order
no. 007505B).
5. Changing the melody
At standby mode, touch the button, you can
hear the melody. Then touch to choose another
melody. There are 4 melodies available. To confirm
the melody you have chosen, touch button.
Recycling instructions
This device may not be disposed of with unsorted
household waste. Owners of old devices are
required by law to dispose of this device correctly.
Contact your town council for further information.
MA_2fam_Video_88351_print.indd 8 11.06.14 08:03
9
GB
Technical and design features may be subject to change without notice.
Troubleshooting
Technical information
Problem Check point
No power
(no picture on monitor) • Isthepowersupplyconnectedcorrectly?
Power is on, but no picture on the
monitor • Isthecablermlyconnectedbetweenthemonitorandthe
camera?
• Isthepolarityofwirescorrectbetweentheoutdoorcamera
unitandindoormonitorunit?
The picture is too dark or white • Adjustbrightnesscontrol
Chime sound is too low • Adjustthevolumecontrol
Indoor unit (8835101) Specifications
Input power DC 14 V (External power supply)
Power consumption Idle mode: 2 W Operating: max 14 W
Connecting system 4 wires: 2 Cameras, 2 Monitors
Call sounds 4
Max. distance and wiring Monitor to camera
50 M: 0.65 mm² wire
100 M: 1.0 mm² wire
Aspect material Acryl
Display 7 Inch Digital wide screen TFT LCD (LED Backlight)
Operating temperature 0 ˚C to +40 ˚C
Dimensions approx. W 200 x H 150 x D 20 mm
Power Supply Specifications
Current 230 V~, DC 14 V , 1.5 A
Outdoor Unit (8835103) Specifications
Input power DC 12 V from monitor
Power Consumption max. 3 W
Material Aluminium
Wiring Monitor: 2 wires Door lock: 2 wires
Image sensor 1/3“ Colour sony super HAD CCD camera
Viewing Angle Diagonal: 90˚ horizontal: 57.8˚ vertical: 48.6˚
Min. Illumination 0.5 Lux
Door lock dry contact
Mounting type Surface mount
Operating temperature -10 ˚C to +50 ˚C
Dimensions approx. W 95 x H 205 x D 20 mm
MA_2fam_Video_88351_print.indd 9 11.06.14 08:03
10
MA_2fam_Video_88351_print.indd 10 11.06.14 08:03
11
MA_2fam_Video_88351_print.indd 11 11.06.14 08:03
148 mm
210 mm
06/2014 UW
Max. 14 Ct./Min aus dem deutschen Festnetz.
Mobil max. 42 Ct./Min.
International calls may vary.
Gutkes GmbH
Rehkamp 13
30853 Langenhagen
Germany
www.gev.de
service@gev.de
Hotline: +49 (0)180/59 58 555
MA_2fam_Video_88351_print.indd 12 11.06.14 08:03
Table of contents
Other GEV Intercom System manuals
