GFS e-Bar 700 70 Series User manual

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
GfSSafety at doors
Assembly instruction GfS e-Bar®
Content
1.0 Introduction
1.1.0 Safety information....................................................................................................................................................... P. 2
1.2.0 General functions......................................................................................................................................................... P. 3
1.3.0 Functions of GfS e-Bar®............................................................................................................................................... P. 4
1.4.0 GfS e-Bar® mechanical................................................................................................................................................ P. 5
1.5.0 GfS e-Bar® mechatronic .............................................................................................................................................. P. 6
2.0 Assembly
2.1.0 Disassembly of GfS e-Bar®.......................................................................................................................................... P. 7
2.2.0 Adjusting pre- and main-alarm ................................................................................................................................... P. 8
2.3.0 Changing of the cylinder.............................................................................................................................................. P. 9
2.4.0 Mounting on metal door.............................................................................................................................................. P. 10
2.5.0 Mounting on wooden door.......................................................................................................................................... P. 11
2.6.0 External power supply................................................................................................................................................. P. 12
2.7.0 Assembly of GfS e-Bar® .............................................................................................................................................. P. 13
2.8.0 Placing Pictos on the door and GfS e-Bar®................................................................................................................. P. 14
3.0 Shortening the GfS e-Bar®
3.1.0 Define the mounting length......................................................................................................................................... P. 15
3.2.0 Shortening.................................................................................................................................................................... P. 16
4.0 Electrical connection
4.1.0 GfS e-Bar® mechanical with floating contact............................................................................................................. P. 17
4.2.0 GfS e-Bar® mechatronic with integrated alarm function........................................................................................... P. 18
4.3.0 GfS e-Bar® mechatronic with integrated alarm function and emergency switch..................................................... P. 19
5.0 Technical data
5.1.0 Electric data ................................................................................................................................................................. P. 20
7007xx_MA_GfS e-Bar_1211_GB
*GfS e-Bar® mechanical has no display

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
2
GfSSafety at doors
1.0 Introduction
1.1.0 Safety information
The GfS e-Bar® is a push-bar, certified acc. to DIN EN1125 and DIN EN 1634 (fire rated doors), which meets highest quality and
safety requirements. It is made out of stainless steel.
To assure the correct functioning of the GfS e-Bar® and to maintain a safe emergency exit route the following guidelines have
to be respected:
•thedoorshallhaveasmoothoperationwithoutanydistortion
•thedoorleafshallbeplanarandstable
•theexistingdoorsealsshallnotaectthecorrectfunctioningofthedoor
•thedistancebetweendoorframeandlockfacingshallbebetween3and6mm
•thetwoexternalmountingpointshavetobepositionedatthesameheight
•theGfSe-Bar®hastobemountedhorizontallyonoutsideopeningdoors
•theGfSe-Bar®hastobemountedincombinationwithcertiedlocksandlockplates
•theGfSe-Bar®hastobemountedonthedoorleafwiththemax.possiblelength
•theinstallationonglassframeddoorsrequiressafetyglass
•theoperationonswing-doorsisprohibited
•lock,strike,bolthavetobemountedinawaythatassuresasafeengagementinthelockingplate
When changing the cylinder lock (European cylinder): employ cylinder with lockable cam.
The mounting has to be done by qualified personnel only.
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
3
GfSSafety at doors
1.2.0 General function/description
Function GfS e-Bar®
mechanic
700 70*
GfS e-Bar®
mechanic with
floating contact
700 71*
GfS e-Bar®
mechatronic
with integrated
alarm function
700 73*
GfS e-Bar®
mechatronic with
integrated alarm
function and
emergency exit
switch
700 74*
For left/right side opening XXXX
Battery driven
(incl. battery control) X
External power supply X X
Pre-Alarm with
floating contact XXX
Main alarm X X X
Single release
(local or remote) X X
Permanent release
(local or remote) X X
Visual and acoustic
“door-too-long-open” alarm X X
Intrusion alarm X X
Changing of parameters X
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
4
GfSSafety at doors
1.3.0 Functions of GfS e-Bar®
The GfS e-Bar® is innovative thanks to intregrated multiple functions. It complies with the European Norm DIN EN 1125 for
push-bars. As all control functions are integrated into the product, no additional means are required to secure the emer-
gency exits. The GfS e-Bar® might secure single- or double-winged panic doors against abuse. In order to increase the in-
hibition threshold, the GfS e-Bar® works with pre- and main alarm.
Door alarm secured
The panic door is alarm secured. The wired GfS e-Bar® display shines constantly
green. The battery operated GfS e-Bar® is working in an energy saving modus
and doesn’t shine.
Step -1 Pre-alarm
While slightly pressing the GfS e-Bar®, a visual red LED light and acoustic
(95 dBA/1 m) pre-alarm is activated. It expires as soon as the GfS e-Bar® is
released. The door remains closed.
Step 2 – general alarm
When pushing the GfS e-Bar® completely, the emergency exit door opens and
the display emits a flashing green light and a permanent acoustic alarm
(95dBA/1m).Onlyanauthorizedpersonwithakeymayswitchoandreacti-
vate the GfS e-Bar®. An automatic alarm shutdown can be set up.
Single release
By using the integrated key switch or by employing an external access control
system, an authorized person may pass the emergency exit once. In case the
door has been left open for more than 10 seconds a gentle “door-too-long-open”
alarm is emitted.
Permanent release
Byusingtheintegratedkeyswitch,anauthorizedpersonmaydeactivatethe
GfS e-Bar® in order to pass the emergency exit for a longer period of time.
This status is communicated by a rising and ebbing green display.
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
5
970/1130/1290
15
15
6.5
43/50
71.3 84.7
9
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
1.4.0 GfS e-Bar® mechanic
1. GfS e-Bar® mechanic
This model is a push-bar incl. a picto describing the operation of the GfS e-Bar®. Neither contacts nor electric functions are
included.TheGfSe-Bar®mechanicwillbesuppliedinthreedierentlengths,whichmightbeshortenedindividually,inorder
to adjust the length to the width of the door.
Length in mm To be shortened by mm Art.-No.
970 180 700 700
1130 160 700 703
1290 160 700 705
2. GfS e-Bar® mechanic with floating contacts
This model is a push-.bar with floating contacts to generate information on the usage of the push bar.
The items will be delivered with a picto describing the operation of the GfS e-Bar®. The GfS e-Bar® mechanic will be supplied in
threedierentlengths,whichmightbeshortenedindividually,inordertoadjustthelengthtothewidthofthedoor.
Length in mm To be shortened by mm Art.-No.
970 180 700 710
1130 160 700 713
1290 160 700 715
To be shortened by 180/160/160 mm
Distance between fastening points

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
6
970/1130/1290
15
15
6.5
9
43/50
71.3 84.7
GfSSafety at doors
1.5.0 GfS e-Bar® mechatronic
1. GfS e-Bar® with integrated alarm (battery operated and/or wired)
This model works either with a 9V battery which is controlled by the PCB or with an external power supply of 10-30VDC.
The battery control function checks every 10 hours the voltage. If the voltage drops below 7V, all 60 seconds an acoustic alarm
is emitted. The battery has to be exchanged. When battery operated the GfS e-Bar® works in an energy saving mode which ba-
sicallymeansthatthegreenLEDsofthedisplayareswitchedo.
TheintelligentPCBrecognizeswhenanexternalpowersupplyisconnectedtotheGfSe-Bar®.Theenergysavingmodeisswit-
chedo.Thedisplayshinespermanentlygreen.Itindicatesthattheemergencyexitissecuredandthealarmfunctionisinope-
ration.
Delivery includes 1 9V battery, 2 keys, 1 picto for the display and the key switch as well as one sticker explaining the operation
on the door.
Length in mm To be shortened by mm Art.-No.
970 180 700 730
1130 160 700 733
1290 160 700 735
Power supply 901 366
2. GfS e-Bar® with integrated alarm and emergency exit switch for opening electrically locked doors
The power supply works with a 10-30 V DC. When connected to an emergency exit control unit the power is supplied by the
emergency exit control unit. The integrated emergency exit switch with 2 opening contacts might be connected to the
emergency exit control unit, a central display. Besides it is recommended to install additionally a reed-contact, in order to
generate a signal that the door has been left open or that somebody has entered the door from the outside.
Delivery includes 1 integrated emergency exit switch, 2 keys, 1 picto for the display and the key switch as well as one
sticker explaining the operation on the door.
Length in mm To be shortened by mm Art.-No.
970 180 700 740
1130 160 700 743
1290 160 700 755
Power supply 901 366
To be shortened by 180/160/160 mm
Display for GfS e-Bar® mechatronic
Distance between fastening points
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
7
1a
1
11
12
10
10
2
5
6
7
8
9a
9
9
4
5
3
3a
GfSSafety at doors
2.0 Assembly
2.1.0 Disassembly of the GfS e-Bar®
Gfs e-Bar® mechanic (77070x)
Press the push-bar 5 profile. Remove the cylinder head
screws M5 x 20 1 . Tear the cover hood 2 out of the
bajonette joint towards the lock side.
Press the push-bar 5 profile. Remove the cylinder head
screws M5 x 20 1a on the hinge side. Tear the cover hood
3 out of the bajonette joint towards the hinge side.
Remove the fixing bracket 4 (bajonette joint). Lift the
push-bar up to its maximum. Hold the lever arm 9 with one
hand and remove the push-bar from the clamping bolt in
opposite direction 10 .
Gfs e-Bar® mechatronic (70071*/77073*/77074*)
Press the push-bar 5 profile. Remove the cylinder head
screws M5 x 20 1 . Tear the cover hood 2 out of the
bajonette joint towards the lock side.
Turn the key clockwise and unlock the cover hood 3a . Turn
the key in the initial position and remove it. Remove the cover
hood. Lift the push-bar up to its maximum. Hold the lever arm
9 with one hand and remove the push-bar from the clamping
bolt in opposite direction 10 .
After loosening the safety catch, lift carefully the plug of the
ribbon cable 6 from the connection circuit board 11 and
store it well protected in the base profile 12 . Loose the
slotted grub screws M4x4 7 and remove them together with
the console 8 .
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
8
(90)
GfSSafety at doors
2.2.0 Adjusting the pre- and main alarm
7007xx_MA_GfS e-Bar_1211_GB
Reed-contact pre-alarm
Reed-contact main-alarm
Jumper
Alarm constant
until reset
Automatic
Buzzer
Buzzer
Jumper to set alarm mode
ofbuzzer
Release magnet
main-alarm
Release magnet
pre-alarm
Reed-Contact main-alarm
Reed-Contact pre-alarm

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
9
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
2.3.0 Changing the cylinder
Mounting European profile cylinder (PHZ) Mounting Swiss round cylinder (RZ)
Use right drill holes
Use left drill holes
Battery holder
Attention:
Employ European profile cylinder with lockable cam.
Just remove key, put cam on 180°!

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
10
21.5/25
43/50
15
20.5
GfSSafety at doors
2.4.0 Mounting on metal doors
Drill hole for suitable
rivet nut M5
Cylinder head screw M5 x12
(not included in shipment)
Drill hole for external connection cable Ø 10
Door handle height:
Attention:
When installing pay attention to the orientation
of the socket. Cam has to show downwards
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
11
BA
25
18
19
38
50
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
2.5.0 Mounting on wooden doors
(Metal cover sheet 777.013 for wooden doors are not included in shipment)
Standard flat steel base plate
Counter sunk screw M4x8
(respect max. length of screw)
Hinge side Lockside
Cover plate lock side
Counter sunk screw M4x8
(respect max. length of screw)
Cover plate
hinge side
Cylinder head screw
wood screw ø 5 x 25
Sunk-wood screw
Ø 5 x 25
Attention:
When installing pay attention to the orientation
of the socket. Cam has to show downwards
Attention:
Cover clip of the standard flat steel
base plate has to be mounted before
the cover hood is mounted.

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
12
15
20.5Door handle height
GfSSafety at doors
2.6.0 External power supply
External connection cable for GfS e-Bar®
with emergency exit switch Ø 9,7 mm
LIYY 20 x 0,25 x 10 mm
External connection cable for GfS e-Bar®
without emergency exit switch
LIYY 12 x 0,14mm
Attention:
Insert cable in a way that it is not
damaged by the push-bar.
Drill hole for external connection cable Ø10
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
13
1a
4 a
1
11
12
10
2
5
6
7
8
9a
9
4
3
3a
GfSSafety at doors
GfS e-Bar mechanical (700.70x)
Insert console 8 into the base profile 12 . Place standard
flat steel base plate (thickness 0.8 mm) between base profile
and console. Snap-in the fixing bracket 4 4a .
Lift the lever arms 9 up to its maximum. Hold the lever arm
with one hand and pull the push-bar profile 5 from the hinge
side on the clamping bolt 10 until the push-bar profile is
engaged. Lift the lever arm with one hand, give some counter
pressure on the push-bar profile with the other hand in order
to avoid that the push-bar snaps-out again.
Insert the cover hoods 2 and 3 in the bajonette joint and
pull it onto the base profile to the dead stop till it snaps-in.
Fix the cover hood 2 with a cylinder head screw M5 x 20
1 . Then fix the cover hood 3 with a cylinder head screw
M5 x 20 1a .
GfS e-Bar mechatronic (70071x, 70073x, 70074x)
Insert console 8 into the base profile 12 . Place standard
flat steel base plate between base profile and console.
Insert carefully plug of (0,8 mm) ribbon cable 6 into the
connection circuit board 11 . Snap-in safety catch.
Snap-in the fixing bracket 4 to the dead stop (bajonette
joint). Lift the push-bar up to its maximum. Hold the lever arm
9 with one hand and pull the push-bar profile 5 from the
hingesideontotheclampingbolts10,tillyourealizethat
the push-bar profile is engaged.
Lower the lever arm 9 with one hand. Give some counter
pressure on the push-bar profile, in order to avoid that the
pus-bar profile 5 snaps out of the clamping bolts 10 .
Insert the cover hood 2 in the bajonette joint and pull it to
the dead stop till it snaps-in. Fix the cover hood 2 with a
cylinder head screw M5 x 20 1 .
Insert the cover hood 3 in the bajonette joint and pull it onto
the base profile to the dead stop till it snaps-in. Turn the key
anti-clockwise till a “click” can be heard. Turn the key in the
initial position and remove it.
2.7.0 Assembly of GfS e-Bar®
Attention:
The standard flat steel base plate between base
profile 12 and console 8 serves to avoid
pressure marks and deformation by the
clamp-connection with the threaded screws M4.
Fasten the four cylinder pins M4 x 6 7 by
hand. Please mind pressure marks.
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
14
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
2.8.0 Placing of the stickers

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
15
15
6.5
15
158 300
83.5
50
Distance between fasteninng points
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
3.0 Shortening of the GfS e-Bar®
3.1.0 Define the required length of the GfS e-Bar®
Distance between fastening points
Front vision
Distance between fastening points
Door handle height
Order length LG = BA + 30
Order lengths To be shortened by max
970 mm 180 mm
1130 mm 160 mm
1290 mm 160 mm
Center of socket

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
16
165
1
2
34
y
y
GfSSafety at doors
3.2.0 Shortening
1. Insert shortening tool into the corresponding profile.
2. Fix the base profile in a bench vice as demonstrated.
The clamp jaws are used as block for the lug of the shortening tool.
Attention: In order to avoid scratches on the surface of the profile,
the profile has to be protected with wooden/ plastic protective sleeves.
3. Position a regular metal saw right next to the lug. Cut the profile parallel to the cover surface.
Light pressure towards the lug makes it easier to cut straight.
4. After having shortened the GfS e-Bar® bur carefully the edges, in order to avoid injuries
Attention: Do not employ “lubricants and coolants” when shortening the GfS e-Bar with mechatronic.
Remove the swarf in the GfS e-Bar® before assembling it. Otherwise risk of short circuit failure.
Order length Length of base profile Length of push-bar
profile
970 mm
67 mm 108 mm1130 mm
1290 mm
Base profile
Base Profile LB ± 1 mm
Standard length
Push-bar profile
Push-bar profile LP ±1 mm
Standard length
always to be shortened
on the hinge side
Order length
Measured distance
between fastening
points
Cuto
940 mm
X
BA 940 - x = y
1100 mm BA 1100 - x = y
1260 mm BA 1260 - x = y
Shortening tool for base profile
Art.-No. 770 712
Lug
Lug
Shortening tool for push-bar
Art.-No. 770 712
Length of base profile
Length of push-bar profile
LD/LT ± 1mm
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
17
1
NO
Pre-alarm Main-alarm
2
NC
3
COM
4
NC
5
NO
6
COM
GfSSafety at doors
7007xx_MA_GfS e-Bar_1211_GB
4.0 Electrical connection
4.1.0 GfS e-Bar® mechanic with floating contact
Clamp Signal Function
1NO Relay 1: Pre-alarm
2NC Relay 1: Pre-alarm
3COM Relay 1: Pre-alarm
4NC Relay 2: Main-alarm
5NO Relay 2: Main-alarm
6COM Relay 2: Main-alarm

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
Rel 1 Rel 2
NC
NO
1
2
4
18
GfSSafety at doors
Clamp Signal Color Function
1NC Relay 2: Main-alarm
2CRelay 2: Main-alarm
3NO Relay 2: Main-alarm
4NC Relay 1: Pre-alarm
5CRelay 1: Pre-alarm
6NO Relay 1: Pre-alarm
7OV Intrusion alarm: When 7-8 are bridged there is no intrusion alarm
8OV Intrusion alarm
9OV Entry for single release (intermittent or permanent signal)
10 GND Entry for single release (intermittent or permanent signal)
11 OV External reed contact (recommended, otherwise bridge 11-12)
12 OV External reed contact (recommended, otherwise bridge 11-12)
13 Emergency Exit Control Units (EECU) – open
14 Emergency Exit Control Units (EECU) – closed
15 CKey switch (reset/programming)
16 NO Key switch (reset/programming)
17 Emergency Exit Control Units (EECU) – Relay
18 Emergency Exit Control Units (EECU) – Relay
19 CInternal emergency switch 1
20 NC Internal emergency switch 2
21 CInternal emergency switch 3
22 NC Internal emergency switch 4
4.2.0 GfS e-Bar® with integrated alarm function, wired
Incoming
Connection
COMMON
Opener
Shutter
Main-alarm EECU-RelNC
Main-alarm EECU-RelC
Main-alarm Key switchNO
Pre-alarm Key switch
Reed contact
NO
T.-intrusion
Pre-alarm EECU-close
Reed contact
C
T.-intrusion
Pre-alarm EECU-open
GND
NO
E/D. open
1
5
3
7
2
6
4
8
9
18
14
16
12
17
13
15
11
10
19
20
21
22
+12-30 V
GND
+9 V Batt
23
25
24
Switching circuit F4
7007xx_MA_GfS e-Bar_1211_GB
Cable diameter LIVY 4x 0,25
}

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
19
GfSSafety at doors
4.3.0 GfS e-Bar® with integrated alarm function and
emergency exit switch for Emergency Exit Control Unit (EECU)
FWS 01 GfS e-Bar®
4
1
3
2
14
28
1
1
8
15
7
14
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
!!! NULL !!!
Flash light + 113
214 315 416 517 618 719 820 921
10 22 11 23 12 24
25 26
Siren +
NC EECU-Rel.
118
19 20 21 22
23 24 25
217 316 415 514 613 712 811 910
CEECU-Rel. NO Key switch NO Key switch CEECU close
NO EECU open T.-Aufbr. Reedcontact T.-Aufbr. Reedcontact
E/D.oen GND
Not1 Not2 Not3 Not4 +12 30V GND +9V Batt
Siren - Lamp emergeny switch (-24 V) Central firealarm system Central firealarm system mergeny switch1-1 mergeny switch1-2 mergeny switch2-1 mergeny switch2-2 Magnet+ Magnet- Magnet NO Magnet COM Magnet NC
Flash light -
Relay NO
Relay NC
Relay COM-
Lamp Emergency switch
(GND)
Sabotage line Sabotage line
Reed contact Reed contact
Openening impuls Openening impuls
7007xx_MA_GfS e-Bar_1211_GB

GfS – Gesellschaft für Sicherheitstechnik mbH · Tempowerkring 15 · D-21079 Hamburg
Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · [e-mail] · www.gfs-online.com
20
GfSSafety at doors
Voltage 9V battery or 12–30V DC power supply
Current draw in battery operation mode
door alarm secured 4 µA
door open 0,5mA, briefly 90mA short-term, intermittent
pre-alarm 190 mA
main-alarm in average 160mA intermittent
Current draw with external power supply
door alarm secured 130 mA
door open 6 mA, briefly 130 mA short-trem intermittent
pre-alarm 235 mA
main-alarm in average 190mA intermittent
Battery low signal below 7V (measured during operation)
Automatic alarm switch o when jumper is set: after 3 minutes
Alarm activation delay in EECU mode 15 sec.
Attention: The code switch has to be positioned on “0”. When releasing the GfS e-Bar® with a key switch, a signal is sent to the
EECU, which releases the magnet. After 15 sec. the magnet will be activated again (or when closing the door again). Therefore
another external reed contact on the door is required. Otherwise a bridge has to be placed on the PCB. The functionality of the reed
contact might lead to an unintentional alarm in case that the activated GfS e-Bar is pushed while the door is still standing open.
Turning angle of pint 40°,9erpin–incasethat45°arerequiredGfSmayoeradierentversion
Power supply unit 230 V AC/12 – 30 V DC
Reed contact with sabatoge line, incl. 2 m cable,
surface or flush mounted (Art-No. 30110/930 210)
External connection cable for GfS e-Bar®
GfS e-Bar®mechanic/mechatronic Recommendation: 12 wires, 12 x 0,14 LIYY
GfS e-Bar®mechatronic + emergency switch Recommendation: 20 wires, 20 x 0,25 LIYY (Art.-No. 770 719)
Suitable cable sleeves:
Metal doors KÜ 480 (Art.-No. 901 802)
Cable sleeve with housing, INOX
Cable sleeve 370 mm, Housing 22 x 480 x 17 mm
Wood doors KÜ-R 480 (Art.-No. 901 902)
Cable sleeve with housing, INOX
Cable sleeve 370 mm, Housing 22 x 480 x 17 mm
Surface mounted KS 370 (Art.-No.. 901 805)
Cable sleeve 370 mm, INOX
5.0 Technical data
5.1.0 Power supply
7007xx_MA_GfS e-Bar_1211_GB