GFW Polar LED Coffee Table User manual

Size:
Colour:
Finish:
100 x 50 x 46 cm (WDH)
White or Grey
High Gloss
POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Polar LED Coffee Table.
Please read the instructions carefully to ensure safe operation of this product
Version 1 - 200505
PO No：
Page 1of 9
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking.
Tools Required
1/2 Hr
Set Up

Version 1 - 200505
Page 2of 9
INFORMATION
CARE INFORMATION
To clean, wipe with a damp cloth.
Never use scourers, abrasives or chemical cleaners as surface shall be scratched.
Do not use solvent based cleaners or detergents as they can bleach or damage the paint.
This product is designed to hold 10Kg in total, spread evenly over the whole unit.
Do not exceed this weight.
Never sit on this product or drag it across the floor as doing this can damage the joints.
We recommend that this unit is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and
a clean, dry area for assembly.
Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent them from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly
Tools not included unless specified in parts list.
WARNINGS
DO NOT
DO NOT
DO NOT
DO NOT
use power tools to construct this product.
tighten screws until parts are assembled or as advised in this guide.
over tighten screws or bolts.
use this product if parts are missing, damaged or worn.
POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
IMPORTANT -READ CAREFULLY -RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.

POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Version 1 - 200505
Page 3of 9
Parts and Fittings Checklist
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer.
The fittings pack contains small items that should be kept away from children.
All parts are packed in one carton
Description: Central Shelf
Qty: 1
Size: 390 x 500 x 35 mm
Carton No: 1/1
Carton No: 1/1
4
Qty: 1
Size:1000 x 500 x 35 mm
123
Description: Top Panel Description: Base Panel
Qty: 1
Size: 1000 x 500 x 35 mm
Carton No: 1/1
lenaPediSllamS:noitpircseD
Qty: 1
Size: 175 x 498 x 35 mm
Carton No: 1/1
5
Description: Large Side Panel
Qty: 1
Size: 385 x 498 x 35 mm
Carton No: 1/1

8
C
Item QuantityCode
Dowel 8x30mm
Version 1 - 200505
Page 4of 9
Fittings (not to scale)
QuantityCode Item
M6 Box Spanner
Metal Tubular
Support
Cover Cap for
Tubular Support
3
1
LLong M6 Double
Ended Bolt
2Q Short M6 Double
Ended Bolt
M
5
DM6 Nut
5
ESpring Washer
For M6 Bolt
Flat Washer
For M6 Bolt 5
F
N
P
2
4
QuantityCode Item
1
LED Clip
1
HBattery Box with
25cm LED Strip
3G Screw for
LED Cable Clips
J
K 1
1
Fittings (packed in each LED pack).
Cable Clip
R
POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Y 4
70 80
10 20 30 40 50 60
Fittings (to scale)
Floor Cushion
Sticky Pads
Battery Box 2
Sided Sticky Pad

Version 1 - 200505
Page 5of 9
Fittings required
For this step:
Tools required
STEP 1
STEP 2
POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
L
Lx3
Cx4
L x3
C x8
Cx4
Place top (1) face down on a clean blanket or non-scratch surface .
Screw in the 3 rods (L) until they stop - do not overtighten.
For this step:
Tools required
Fittings required

Fittings required
POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
Version 1 - 200505
Page 6of 9
STEP 3
STEP 4
For this step:
Tools required
P
P
N
N x1
P x2
J x1
H x1
K x1
G x3
K
G
G
J
R
H
G
R x1

POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
Version 1 - 200505
Page 7of 9
STEP 5
STEP 6
For this step:
Tools required
Fittings required
Q x2
P
P
N
N x1
P x2
Qx2
Screw in the 2 rods (Q) until
they stop - do not over-tighten
Q

POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
Version 1 - 200505
Page 8of 9
STEP 7
ii
i
iii iv
CHANGING THE BATTERIES
SLIDE OFF THE LID CHANGE BATTERIES
SLIDE LID BACK ON
USE GOOD QUALITY AA BATTERIES. FOR BEST RESULTS USE RE-CHARGEABLES.
F x5
M
D x5
E x5
E
F
M
D
Yx4
Y x4
Peel off

POLAR HIGH GLOSS LED COFFEE TABLE ASSEMBLY INSTRUCTIONS
Version 1 - 200505
Page 9of 9
Assembly Completed
Your Polar Coffee Table is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference