GFW LANCASTER User manual

LANCASTER - SLIDING COFFEE TABLE ASSEMBLY INSTRUCTIONS
Thank you for purchasing the SLIDING COFFEE TABLE.
Please read the instructions carefully to ensure safe operation of the product.
Batch No : PO# 3900
Size: (W)1050 x (D) 470 x (H)415mm
Colour : Bianco Oak / Lancaster Grey
PagePage 1 of 11
1
V1 9/18

Page 2 of 11
The Product is intended for a maximum load of 15kg with the Top in the closed Position .
It is recommended that any heavy items over 5kg removed from the top before sliding
open to maintain the stability of the table .
The top compartment and bottom Shelf are designed to hold evenly distributed loads upto a maximum of 10kg .
Due to the size of this product we recommend that is assembled in the room intended for use.
When you ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly
Unwrap all packaging materials and place the components on top of the carton box or not on a clean floor to
prevent it from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Make sure the legs remain in contact with the ground.
Tools not included.
DO NOT use power tools to construct this product.
DO NOT tighten screw until fully assembled.
DO NOT over tighten screw or bolts.
DO NOT stand or sit on this Table.
DO NOT place hot items or liquids directly onto the top surface otherwise this will permanently damage the item.
Always use a heat resistant mat if placing such items on the surface.
Never use scourers, abrasives or chemical cleaners.
Any spilled liquids must be wiped up and removed immediately .
Clean with a gentle sponge or clean cloth using warm soapy making sure that any residual liquid is fully removed.
Do not use Solvent based cleaners or Detergents as they can bleach and damage the product.
To clean wipe with a sponge and soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.
V1 9/18

Side Panel (L) (15 x 395 x 390mm)A 1
BSide Panel (R) (15 x 395 x 390mm) 1
CTop Panel (25 x 470 x 1050mm) 1
DBottom Panel (15 x 365 x 920mm) 1
EFront Bar (15 x 100 x 920mm) 2
FBottom Bar (15 x 50 x 920mm) 2
GFront Panel (L) (15 x 50 x 390mm) 2
HFront Panel (R) (15 x 50 x 390mm) 2
ISupport Bar (15 x 60 x 365mm) 1
JSupport Bar (15 x 60 x 365mm) 1
KSupport Bar (15 x 80 x 365mm) 2
ZCenter panel (2.5 x 374 x 929mm) 1
Page 3 of 11 V1 9/18
I
C
G
E
A
B
E
H
G
H
Z
J
K
K
D
F
F

5
3
12x
a
Unitar Screw
D6.3 x 40mm
28x
b
Wooden Dowel
D8 x 30mm
18x
c
Minifix Bolt
M5 x 29mm
Page 4 of 11V1 9/18
18x
f
Minifix Cam
D15 x 12mm
4x
e
Nail Leg
5 x 8 x 13.5mm
1x
i
Allen Key
M4
16x
h
Round Sticker
(D-19mm)
16x
d
Csk Screw
M3.5 x 15mm
1sets
g
Extention Drawer Slide
(2way)
400mm

STEP 1
28 x
b
Page 5 of 11 V1 9/18
A
Parts Required Qty
Panel (A)
Panel (B)
Panel (D)
1
1
1
Parts Required Qty
Panel (E)
Panel ( I )
Panel (J)
2
1
1
Panel (K) 2
X2
B
D
E
J
I
K
X2
b
b
b
b
b
b
b
b

STEP 2
STEP 3
Page 6 of 11 V1 9/18
d
f
18 x
c
Parts Required Qty
Panel (E)
Panel (F)
2
2
Parts Required Qty
Panel (G)
Panel (H)
2
2
Parts Required Qty
Panel (A)
Panel (B)
1
1
c
E
F
H
G
c
c
c
f
f
A
G
H
G
H
B
14 x
f
Panel (D) 1
Panel (F)
Panel (G)
2
2
Panel (H) 2
f
D
F
F
X2
X2
X2
X2

STEP 4
STEP 5
Page 7 of 11 V1 9/18
E
Parts Required Qty
Panel (E)
Panel (I)
Panel (J)
2
1
1
Panel (K) 2
Parts Required Qty
Panel (B) 1
4 x
f
E
K
K
I
J
f
a
i
B
E
E
K
K
I
J
H
4 x
a
i
i
a

STEP 6
STEP 7
g
f
Page 8 of 11V1 9/18
c
Z
a
i
2 x
a
i
a
i
K
K
EB
H
J
B
H
D
E
F
F
Parts Required Qty
Panel (Z) 1
Parts Required Qty
Panel (D) 1

STEP 8
STEP 9
Page 9 of 11V1 9/18
Parts Required Qty
Panel (A) 1
g
1 sets
8 x
d
Panel (I / J)
g
d
d
g
g
d
A
D
ZE
F
A
D
Z
E
F
G
4 x
e
6 x
a
i
e
a
i

STEP 10
STEP 11
Page 10 of 11 V1 9/18
6 x
d
2 x
d
C
A
C
A
E
D
d
d
C
Z
Parts Required Qty
Panel (C) 1
d
g
d
g
h
16 x
h
d
*Slide top to
opposite side
C
d