GGM gastro HCH2010 User manual

1
HCH2010 CUTTING MIXER MACHINE
OPERATION MANUAL

2
Preface
In order to make sure the machine can be used efficiently, we provide concerned
details and information of the machine in this manual, include specifications, operation
procedures and instructions.
This manual should be submited to the qualified operators, to help them get familiar
with the operation and maintenance of the machine.

3
Chapter 1 General Introduction
1.1 Product Function
HCH2010 Cutting mixer machine produced by our company is mainly used for food
processing fields, which can process different kinds of roots, stems, leaves and vegetable
into paste speedly and effectively, which can process meat and accessories into glue. It can
also mix different kinds of stuffings evenly, which is the ideal equipment for processing
dumpling and buns, and also the best choice for feed processing field.
1.2 Performance and Features
Principle of relative motion is adopted in this machine, which makes the processing
food and high-speed rotating blades-unit to do vertical relative motion, and differential
rotary cut the food into paste. Steamline appearance and fully enclosed box type body are
designed, all motivation and driving devices are installed inside of the body, which make
the machine with fine craftmanship and excellent structure.
The machine blade speed, pot speed, blade material and hardness are designed as the best
combination. The blades are sharp, rable and sophisticated, which ensures good cutting
efficience, slight temperature lifting and short cutting time, which also improves the
emulsification, the elastic, the smooth and the yield of stuffings.
Toutching switch is adopted in the controlling system of HCH2010 Cutting mixer machine,
which is with features of good waterproof properties, safety, reliability, long service life,
low noise, simple operation and easy maintenance.
Chapter 2 Structure and Principle
2.1 Main structure
The machine is mainly composed of frame, turbine driving device, blades-unit, dish basin,
basin cover, pulley mechanism, motor and other main components(see picture 1).

4
Picture 1: structure diagram
2.2 Material safety
The machine parts which contact with food diretly are made of material strictly in
accordance with the requests of food safety and health standards, which is not rust,
corrosion, nontoxic and harmless to buman health even after using for a long time.
2.3 Working principle
When the machine is working, close the basin cover, and put different kinds of roots, stems,
leaves, vegetable, meat and so on into the basin, the food rotates anti-clockwise with the
basin, which will be cut into paste when coming across with vertically rotating blades(size
of the paste is to be controlled by adjusting the cutting time).
2.4 Electrical circuit diagram
The machine is equipped with an input cable with cross section 3X1.5 mm2, length 1.5m.
The machine should be connected to power source as 220V/50Hz.
Attention: socket must be equipped with switch, to make sure power can be cut off on time.
frame
belt pulley mechanism
turbine driving device
blades-unit
dish basin
motor
basin cover

5
Picture 2: electrical circuit diagram
Table 1. Remarks for element symbols
Remark: European voltage: 220-240Vac，50Hz
M
Motor
ES
Emergency stop
SW1
Magnetic switch
SB1
Start button
SB2
Stop button
Chapter 3 Main Technical Data
3.1 Dimension and weight
Picture 3: dimension
3.2 Main techinical data
Table 2: Main techinical data

6
Capacity
（kg / h）
Blade
rotating
speed
（r/min）
Basin
rotating
speed
（r/min）
Motor
power
（KW）
Voltage
（V）
Frequency
（Hz）
Waterproof
grade
Belt
model
Net weight
（kg）
300
1440
12
1.5
220-230
50
IPX1
A550
A860
135
Chapter 4 Packing and Inspection
4.1 Packing inspection
The machine must be packed well before shipment with the following(see picture 4)
a. carton and plate
b. cutting mixer machine
c. operation manual
a b c
Picture 4: Packing composition
4.2 Inspection
Make sure there is no damage on the labels outside of carton before uppacking. If there is
damage while transportation(like scars or labels taken off), please list out all the damaged
parts in 3 days after the date on document, and contact with the supplier. While
transportation, please keep the machine parallel with the ground, please do not inverted the
machine.
4.3 Packing material disposal
All packing material(cartons, plastic bags, polyurethane foam) can be disposed as normal
city garbage. In countries with special requirments and standard on waste disposal, please
dispose strictly obey the local laws.

7
Chapter 5 Installation
5.1 Place the machine
Placed the machine in dry and ventilated level surface, to ensure the smooth and safe machine work.
Choose the placement space should satisfy the size in figure 1 (based on the model), can accommodate.
5.2 Connection
Stretching elongation power cord, with grounding symbol of wire core, reliable grounding, three other
line core (single-phase motor for two) respectively received a matching circuit breaker (the user should
bring along their own) extension line terminal blocks, reliable and marks on equipotential connection
wires.
5.3 Preoperational check
Before the first operation, need to press these steps:
1. Carefully unwrapped the package and read the "instruction manual".
2. Inspection on each parts, whether the fasteners loose in transit, switch and the power cord is
damaged due to transport, and check the power supply voltage and existing product use voltage
is matched.
3. Check whether there is foreign body inside the dish basin, if there is any foreign body clean up in
time, so as to avoid external hard impurities caused damage of cutting tools and other machine
parts.
Chapter 6 Operation
6.1 Switch control
Control switch button(picture 5):
1—Green button means “start”
2—Red button means “stop”
3—Rotating red button means emergency stop
3
2
1

8
6.2 Instructions
Note: when the motor stops rotating, the food can be loaded
According to the following steps:
1. Plug in the power supply.
2. Open the cover, put in the right amount of ingredients, pay attention to not too full, with no access to
the pot cover advisable. Large pieces of vegetables should be cut into small pieces, throw food do not
wrong to foreign bodies during the process of food basin, otherwise will damage the cutting tool.
3. Close the cover.
4. Press the green button, startup power, machine works, the machine should be smooth operation, no
abnormal sound.
5. According to the raw material used to set up the reasonable technical parameters, too much charge, or
a plate of chopping time is too long will not achieve the ideal process effect.
6. Each time before machine works, check and make sure if there are no foreign bodies in the basin, and
must not be mixed in the cut material is hard and foreign body, so as not to damage the blades or other
equipment failure.
7. After finish cuting material in the basin, press the red button, dish basin and cutting blade all stop
running, power off.
8. With the special shovel, remove the basin of chopped turnip.
9. Cleaning after using in every time after work, should be effectively clean, and keep the machine dry.
10. The machine after use, downtime, pull out the power supply.
Chapter 7 Regular Cleaning
Note: Don’t put hands into the running machine.
Cleaning and maintenance work only at the time of machine stop and power off.
7.1 General
1. To disconnect the power and pull out the plug before cleaning machine.
2. The machine must be to clean after work every day, all come into contact with the food of the
mechanical parts to clean and in place.

9
3. Because of the waste residue will damage the machine, the machine to clean both inside and
outside.
4. Don’t use water detergents, industrial cleaners, iron brush, hoses, and beneath the surface of the
machine cleaning equipment.
Chapter 8 Machine Maintenance and Daily Inspection
Note: before the maintenance operation work: please unplug the power before servicing the
machine, make sure the machine away from the power.
8.1 The necessity for regular maintenance
1. Regularly for cutting mixer machine maintenance, can effectively extend the service life.
2. Periodically for cutting mixer machine cleaning, can ensure food quality and safety.
8.2 Daily inspection of key components
1. Cutting blade
Should check the cutting blade whether installation firm, have any damage, before starting the
machine.
2. Belt
Belt should be regularly adjusted, after 2-3 years belts will be replaced, it is necessary to contact
"service center".
3. FEET
With the passage of time, the feet damage will cause unstable machines placed, if this happens,
please replace the feet.
4. Cable
Regularly check the cable, replace if necessary, please contact the service center.
8.3 Regarding how to adjust the gap between the blade and the chopping pot, the operation
steps are as follows:
1. When the gap between the blade and the bottom of the chopping pot is too large, first
remove the lock-blade screw nut with an open-end wrench, and then remove the shaft end
pad, blade and blade seat in turn, as shown in the following figure.

10
2. Stack the 3 cutting blades together, use the 6-inch semicircle file provided by the
machine to grind the bulge on the blades to the appropriate size, and ensure that the
grinding size of the three blades is the same, that is, the bulge should be of the same height.
As shown below.
3.Finally, install the blade holder, blade, shaft end pad and lock-blade screw nut in place
according to the previous dismantling sequence, and use an open-end wrench to lock the
lock-blade screw nut.
bulge
lock-blade screw nut
shaft end pad
blade
blade seat

11
Chapter 9 Recycling Method
9.1 No repairing
For some reason the machine cannot be repaired, to ensure the machine can't use again, cancel all
electrical connections.
9.2 Discard
When the machine can't repair it abandoned, please contact the waste disposal company, will be
qualified materials used in the manufacture of a variety of other components.
9.3 Electrical and electronic waste
According to the standard of 2002/95 / EC, 2002/96 / EC and 2002/108 / EC, limit the use of certain
hazardous substances in electrical and electronic equipment.
The logo on the products or packaging, means that the product cannot be discarded as household waste.
Waste collection to classification, managed by the manufacturer, the user has the responsibility to
contact the manufacturers, manufacturers should be classified collection of waste in accordance
with the waste disposal system.
Classified collection and recycling of waste disposal equipment will help to protect the natural
resources.
To ensure recycling that can protect human health and the environment. (export dedicated )