GGM gastro HLP-15 User manual

,QVWUXFWLRQIRU3RWDWR3HHOHU.6+
GGM Gastro International GmbH
Weinerpark 16
48607 Ochtrup
Tel: [phone]
Fax: [phone]
[email protected]
www.ggmgastro.com
Geschäftsführer: Ferit Inan & Ömer Elma
Es gelten unsere auf der Website www.ggmgastro.com ausgewiesenen AGB‘s.

INTRODUCTION
zThis manual has been written to provide the client with all information concerning the
machine and the norms pertaining to it, apart from the use and maintenance instructions
which enable it to be used in the best way possible, therefore maintaining its efficiency
through time.
zThis manual must be given to all personnel who will use or do maintenance on the machine.
INDEX OF CHAPTERS
CHAP.1 - MACHINE INFORMATION
1.1 —GENERAL PRECAUTIONS
1.2 —SAFETY DEVICES INSTALLED ON THE MACHINE
1.3 —DESCRIPTION OF THE MACHINE
1.3.1 _General description
1.3.2 _Constructive features
1.3.3 _Machine makeup
1.3.4 _Intended use
1.3.5 _Improper use
1.3.6 _Residual risk
CHAP.2 – TECHNICAL DATA
2.1 —DIMENSIONS,WEIGHT,CHARACTERISTICS...
CHAP.3 – RECEIVING THE MACHINE
3.1 —SHIPPING THE MACHINE
3.2 —CHECKING THE PACKAGE UPON RECEIPT
3.3 —DISPOSING OF THE PACKAGE
CHAP.4 – INSTALLATION
4.1 —MACHINE PLACEMENT
4.2 —ELECTRICAL CONNECTIONS
4.2.1—HLP with single-phase motor
4.3—ELECTRICAL DIAGRAMS
4.4—OPERATIONAL CHECK
CHAP.5 –MACHINE USE
5.1 —CONTROLS
5.2 —LOADING AND WORKING THE PRODUCT
CHAP.6-ROUTINECLEANING
6.1 —GENERALITIES
1

CHAP.7-MAINTENANCE
7.1—GENERALITIES
7.2—BELT
7.3—FEET
7.4—FEEDING CABLE
CHAP.8-DISMANTLING
8.1—PUTTING IT OUT OF WORK
8.2—DISPOSAL
8.3—WEEE Waste of Electric and Electronic Equipment
CHAP.9- RESOLUTION TO ACCIDENT OR BREAKDOWN OFTHE MACHINE
2

CHAP.1 - MACHINE INFORMATION
1.1-GENERAL PRECAUTIONS
zThe machine must only be used by trained personnel who are perfectly aware of the safety
norms contained in this manual.
zIf there is a turnover of staff, promptly provide proper training for new personnel.
zEven if safety devices are installed on the machine do not place hands near moving parts and
avoid touching the machine with wet or damp hands.
zBefore carrying out any type of maintenance or cleaning ,disconnect the machine plug from
the electrical outlet.
zWhen intervening for maintenance or cleaning purposes (therefore the protections are
removed) carefully evaluate residual risks.
zDuring maintenance or cleaning always concentrate on the operation in progress.
zRegularly check the state of the feeding cable (completely unwinding the cable, avoiding
twisting it , is advisable to avoid potential risks); a worn or broken cable can present serious
danger of the electrical kind; aviod compressing the wire with weights, leaving it in contact
with hot or sharp surfaces and pulling on it to unplug it from the outlet.
zIf the machine shows signs of malfunctioning or does not work, do not use it or try to repair it;
contact the “Assistance Center”, indicated on the back of this manual.
zThe OUT pushbutton must only be used for unloading the worked product.
zThe potato shall be washed cleanly before put into food process chamber.
zWarning: Don’t move the grounding terminal without instructed by qualified personnel.
zWarning: This machine should be placed the location away from the children can touch, and
the machine should be operated under qualified personnel.
zIf the fuse breakdown or out of function, please replace the following fuse rated 10A or call
the maintenance servicer for replacement.
(a) Model 5F-Series or 5T-Series made by XC Electronics (Shen Zhen) Corp. Ltd;
(b) Model 522 made by Dongguan Better Electronic Technology Co., Ltd
zWarning: Don’t remove the fix guard on the motor enclosure and control panel without the
instruction of qualified personnel.
The manufacturer is not responsible in the following cases:
→if the machine is mishandled or the safety devices are installed by unauthorized personnel;
→if components are replaced with unoriginal parts;
→if the instructions in this manual are not followed carefully;
→if the machine surfaces are treated with inappropriate products(inflammable, corrosive or
harmful substances).
3

1.2–SAFETY DEVICES INSTALLED ON THE MACHINE
The safety devices against risks of electrical nature conform with the norms EN60335-1,EN
55014 and the directives 2006/95/CEE, 2004/108/CEE ，while the mechanical safety devices
conform with the directives2006/42 CEE.
The machine is equipped with:
za starting device consisting of a control card insulated in IP 34,24 Volts, which enables:
—turning the machine on and off;
—controlling the unloading of the product;
—controlling the safety micros;
za micro,which causes the machine to stop in case the cover or discharge door opens(see FIG.n
° 1),does not allow the machine to turn on if it is not in the closed position;
zan N.V.R. device in the control circuit which requires the machine to be restarted if there is
an accidental lack of electricity and it enables restarting the machine only by using the
START pushbutton;
Furthermore the machine is equipped with an upper transparent cover which enables checking the
working of the product in progress without any risks.
1.3–DESCRIPTION OF THE MACHINE
1.3.1–Genneral description
The line of CE professional HLP has been designed and manufactured by our company with the
precise objective of guaranteeing:
zmaximum safety during use ,cleaning and maintenance;
zmaximum hygiene, the result of the careful selection of materials which come into contact
with foodstuffs and due to the elimination of sharp edges from the part which comes into
contact with the product ,in such a way to guarantee easy and thorough cleaning;
zall the components are robust and stable;
zmaximum silence thanks to the belt trasmission.
1.3.2–Constructive features
Professional I HLP is made of Stainless steel, Aluminum and magnesium.
The discharge door is polished aluminum; the adjustable feet are stainless steel; the cover is a
plastic material, while the hopper is made of Aluminum and magnesium steel, the work plate is
aluminum with the disk made of Stainless steel, Aluminum and magnesium; the internal walls of
the container are in abrasive resin to enable a higher lever of abrasion with the product to be
worked.
1.3.3–Machine makeup
FIG.n
° 1-General view of the machine
4

KEY:
1. pushbutton strip
2. hopper
3. cover block hinge
4. pan
5. pan block hinge
6. maintenance door
7. feet
8. structure
9. discharge door
10. cover
11. feeding tap
12. hangdle
13. stand
NB: there is the possibility of adding the sieve
to the stand to collect waste.
Note: The Machine shall be fitted with four
feet first to ensure its stability.
1.3.7 – Intended Use
Our p tato peeler is inten
o ded to used
indoor and for commercial use, not for
outdoor use. This machine is only
designed to peel the cleaning potato and
use the public water circulation to carry
away the waste. Following is the normally
working condition according to the model
no described in Page 6:
zAmbient temperature range: +5 ° C - +40 ° C
zHumidity range:> 50% (Maximum temperature: +40 º C)
zAltitude: <1000 m
1.3.8 – Improper Use
–This machine is not designed for continuous operation and household use;
–Rigidity object is not allowed to put in peeling chamber;
–This machine is not allowed working under explosive environment, please do not place
machine near hot resource or other dangerous place;
Please take properly protection to prevent particles of
–dirt, duct etc, into your eyes, Always be
attention to keep a safety distance from your work area during normal use;
–Please wear ear shield to prevent high noise emission during normal use.
5

1.3.9 – Residual risk
Even with proper use of equipment always remains some residual risk that can not be excluded.
From the type and design of the device, the following potential hazards can be derived:
- The operator forgets to wear hearing protection.
- The operator opens the valve before connecting the water hose.
If the details provided in your instruction manual instructions are not followed, the residual risks
can occur because of improper use
CHAP.2 – TECHNICAL DATA
2.1 – DIMENSIONS, WEIGHT, CHARACTERISTICS...
FIG.n
° 2 — Drawings of dimensions
TAB.n°1-MEASUREMENTS AND TECHNICAL FEATURES
Model HLP-15 HLP-20
Power source 220-240V/50HZ
A*B mm 245*360 290*370
C*D*E mm 410*550*1060 460*590*1100
F mm 1490 1520
Capacity kg 15 20
Output/h. kg/h 165 225
Motor Hp 1 1.5
Power watt 1000 1250
Net weight kg 61 68
Volume of bottle L 27.4 36.6
Sound pressure level dB 74.5 74.5
Uncertainty dB 2.5 2.5
ATTENTION: The electrical characteristics the machine is prearranged for are indicated by a
plate (attached to the back);before connecting the machine see 4.2 electrical connection.
6

CHAP.3 – RECEIVING THE MACHINE
3.1--SHIPPING THE MACHINE (see FIG.n
° 3)
The machine leaves our warehouses correctly packaged, such a package consists of:
a) An external box in robust cardboard and a wooden pallet;
b) The machine;
c) This manual;
d) Stand with sieve.
b) a)
d）c)
FIG.n
° 3-Package description
WARNING: THIS MACHINE SHOULD ONLY BE TRANSPORTATION AND STORAGE
WHIN THE RANGE OF TEMPERATURE -25°C to +55°C.70°C COULD BE ONLY
GUARANTEED FOR A SHORT PERIODS (24H).
3.2–CHECKING THE PACKAGE UPON RECEIPT
When the package is received, if there is no external damage, open the package and check that all
the material is inside(see FIG.n
° 3)
If the package shows signs of mishandling, bumps or falls upon delivery, the shipping company
7

must be made aware of the damage within 3 days of the delivery date indicated on the documents,
and a detailed report must be written on the damage to the machine. Do not overturn the
package!! when the package is being moved make sure that it is firmly held in the four
fundamental points(keeping it parallel to the floor).
3.3–DISPOSING OF THE PACKAGE
The package components (cardboard, pallets,plastic and polyurethan foam strap)are produced like
solid urban waste, therefore they can easily be disposed of.
If the machine id installed in countries with particular norms, dispose of the packages according to
the laws in force.
CHAP.4 – INSTALLATION
4.1 – MACHINE PLACEMENT
When choosing the plane the machine will be placed on the
dimensions shown in Tab.1 must be considered (based on
model),therefore the surfaces must be wide enough to hold
it ,and it must be well-levelled and dry.
Prearrange a discharge tube (φ60mm.)under the machine and a
drain trap on the floor, or a floor grate to collect the water or
other waste material.
Furthermore the machine must be placed as near as possible to
a faucet (φ12mm.), which enables
the feeding tube to be easily and safely attached(see FIG.n°4 )
Once the machine is placed proceed to blocking it by fastening
it to the floor with the setscrews on the flanged feet(see
FIG.).Furethermore the machine must be placed in an
environment with a maximum humidity of 75%,which is not
salty and has a temperature between +5℃and +25℃; in any
case in environments which do not bring about its malfunctioning.
FIG.n
° 4-Discharge diagram
4.2 --ELECTRICALCONNECTIONS
4.2.1—HLPwith single-phase motor
The machine is outfitted with a feeding cable with a cross section area of 3x1.0mm2, length 1.5m.
Connect the machine to 220-240V.50HZ
Please bonded the wiring marked the symbol together during the connection.
If finding the cable is out of function or destroy, please contact the local service for replacement.
Furthermore check that the data shown on the serial number-technical plate(FIG.n°5) correspond
to the data on the delivery notes.
8

FIG.n°5-Serial number-technical plate
Before finally connecting the machine to the three-phase feeder line ,check the direction of
rotation of the cap by pressing the START pushbutton(see FIG.n
° 8)then immediately stop it by
pressing the STOP pushbutton.
The direction of rotation of the cap seen from the discharge outlet must be counterclockwise;if the
direction of rotation is not exact, invert two of the three feeding wires in the plug or outlet(see
FIG.n ° 7).
9

4.3- ELECTRICALDIAGRAMS
FIG.n
° 6-1ph electrical diagram
Note: SQ1 and SQ2 is the interlocking switch provided on the feeding opening and output opening
guards. When open the feeding lid or output door, interlock switch will be on OFF position and
cut off the power.
10

4.4-OPERATIONAL CHECK
Before proceeding to testing make sure the upper cover and the discharge door are well-blocked,
then check the running of the machine with the following procedure:
1check that the upper cover and the discharge door are closed well;
2press the START pushbutton and then the STOP one;
3repeat the same operation, checking that the cap rotates in a counterclockwise direction(see
FIG.n
° 7) through the closed transparent upper cover;
4check if the machine stops when running by opening the cover or discharge door, and once it
is closed if the machine restarts by pushing the START pushbutton;
5to discharge the material open the discharge door , keeping it open with your right hand and
at the same time pushing the OUT and START buttons on the pushbutton strip with your left
hand ; the machine will start by unloading the potatoes by centrifugal force(see FIG.n
° 10).
FIG.n ° 7-Cap rotation
CHAP.5 –MACHINE USE
5.1 –CONTROLS
The controls are located on the pushbutton
strip above.
1 OUT is pushbutton for the automatic
discharge of the product; it works only if it is
pressed at the time as START button.
2 STOP is the pushbutton to stop the
machine.
3 START is the pushbutton to start the
machine.
4 Timer(max time 5 min.).
FIG.n
° 8-Position of controls
11

5.2-LOARDING AND WORKING
THE PRODUCT (see FIG.n
° 9)
NB: The goods to be worked are loaded gradually on the cap from the upper cover when the
motor is off.
Adhere to the following procedure:
per cover,
2e machine is not too full and
3ocal public water
5ater flow using the faucet on
.n
° 9-Loading the product
unning: desired work time with the timer(max time 5 min.);
r moved while the machine is
4peatedly unload the slag tray, to avoid the
nloading the worked product:
er faucet and put a big container
2the discharge door ,
3e the unloading is complete the machine
1load the product from the up
making sure that the discharge door is
closed well;
check that th
that the level of the product does not go
over the abrasive band inside the machine;
close the upper cover;
4Connect the tap to l
supply;
open the w
the hopper;
FIG
Note: The connection of public water supply
shall comply with local law or relevant
regulations.
R
1set the
2then start the machine by pressing the START pushbutton;
3if the cover and/or discharge door are accidentally opened o
running, the machine will stop; when closed press the START button;
open the water flow using the faucet on the hopper;
5if the machine is outfitted with a stand with sieve, re
water dripping.
U
(see FIG.n
° 10)
1close the wat
near the discharge outlet;
to unload the material open
keeping it open with your right hand ; press
the OUT and START pushbutton at the same
time with OUT your left hand; the machine
will start unloading the product by
centrifugal force;
FIG.n
° 10-Unloading the product
onc
12

will stop by releasing the pushbuttons and the discharge door;
.:
N.B an empty machine turn.
Avoid making
HAP.6-ROUTINE CLEANING
TTENTION: never put hands inside the moving machine.
C
A
leaning and maintenance operations are carried out only when the
.1-GENERALITIES hine the feeding plug must be disconnected
C
machine is off and the feeding cable is unplugged.
6
Before cleaning the mac
from the network to completely isolate the machine.
zThe machine must be cleaned at least once in week and all the
zthe outside of the machine must be cleaned
zThe machine must not be cleaned w es,
zh a sieve repeat-edly empty the slag tray to avoid the water
zrocedure:
ne and draw out of the plug;
lly, and separated from the live parts;
;
ualified personnel.
HAP.7-MAINTENANCE
.1-GENERALITIES aintenance activity it is necessary to:
e the machine from the rest of
.2-BELT s not need any adjustments. Usually, after 3/4 years it must be replaced, in this case
parts of the machine (completely removable) which come into
direct or indirect contact with the worked foodstuff must be
carefully cared for.
Both the inside and
because the residual waste can be seriously damaging.
FIG.n
° 11
ith water cleaners, high-pressure jets of water, brush
and anything else which can damage it on the surface.Acidic, corrosive or inflammable
substances must not be used.
If the machine has a stand wit
dripping.
Cleaning P
- Power off the machi
- Take the machine away from dangerous place;
- Dismantle the assembly needed cleaning carefu
- Cleaning the assembly with tap water, using the rag or other soft cloth to rub the waste
- Take the assembly to dry location and cleaning machine;
- Installation the machine according to the FIG.n°11 or under q
C
7
Before carrying out any m
Disconnect the plug from the electrical outlet to completely isolat
the system.
7
The belt doe
call the “ASSISTANCE CENTER”.
13

7.3-FEET deteriorate with time, thus reducing the stability of the machine. therefore they
.4-FEEDING CABLE ar of the cable and call the “ASSISTANCE CENTER” to replace it.
HAP.8-DISMANTLING
T OUT OFWORK e machine out of work make sure that it cannot be used by
.2-DISPOSAL ut out of work the machine can be eliminated. To correctly dispose of the
te of
Equipment
irective 2002/95/EC,2002/96/EC and 2003/108/EC on the restriction of the use of certain c
rossed out wheelie bin , on the product or in its packaging indicates that this
eparate waste collection of this appliance is organised and managed by the manufacturer. It is
he separate collection and recycling of your waste equipment at the time of disposal will help to
HAP.9 – RESOLUTION TO ACCIDENT OR BREAKDOWN OF THE MACHINE
ARNING: If found the breakdown or abnormal operation of machine, please disconnect the
M
The feet could
must be replaced.
7
Periodically check the we
C
8.1-PUTTING I
If for some reason it is decided to put th
anyone: unplug the electrical connections.
8
Once it has been p
machine get infirmation from any company responsible for such a service and take careful no
the material used for the various components.
8.3-WEEE Waste of Electric and Electronic
D
hazardous substances in electrical and electrical equipment ,and waste electrical and electroni
equipment
This symbol, c
product must not be disposed of with your other household waste.
S
the user’s responsibility to contact the manufacturer and follow the waste treatment system the
manufacturer has adopted for separate waste collection.
T
conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment.
C
W
power supply, remove the machine from hazardous location and contact the “ASSISTANCE
CENTER” for maintenance. PLEASE NOT OPEN THE COVER TO CHECK THE PROBLE
BYYOURSLEF UNLESS THE QUALIFIED PERSONNEL.
14

15 15

No. Name No. Name
1 Fixed Guard 29 203 Bearing
2 Timer 30 Sleeving
3 Arm Spacer 31 O Type Sealing
4 Arm Shaft 32 Belt Wheel
5 Cam 33 Electric Box
6 Limited Pad 34 B-Ribbed Belt
7 Arm Switch 35 Motor
8 Arm Tubing 36 Motor Bracket
9 Glass Lid 37 Transmission Base
10 Switch Box 38 Adjust. Foot Mat
11 Button（White） 39 Supporting Bar
12 Button（Red） 40 Foot Mat
13 Button（Green） 41 Water Output
14 Knob 42 Water Reservoir
15 Water Inlet Valve 43 Strain less Nut
16 Strain less Nut 44 Screen Pot
17 Top Lid 45 Bottom Board
18 Rotating Plate 46 Power Cord
19 Rotating Assembly 47 Plut
20 Side Peeling Sheet 48 Side Board
21 Bottle 49 Rear Board
22 Output 50 Enclosure
23 Output Handle 51 Interlock Switch
24 Bolt 52 Buckle
25 Level 53 Buffer Screw
26 Switch Actuator 54 Drive Base
27 Sealing 55 Frame
28 Bearing Assembly
16