GGM gastro GGM-BRG01-E15-0001 User manual

GGM GASTRO INTERNATIONAL GMBH
WEİNERPARK 16 – 48607 OCHTRUP
TEL:[phone] / 7220 0 –FAX: [phone]
www.ggmgastro.com –[e-mail]
USER GUIDE
BURGER MACHINE

2
CONTENTS
A –GENERAL INFORMATION
Page 3
A1 –PRODUCT DESCRIPTION
Page 4
A2 –TECHINICAL INFORMATION
Page 4
A3 –TRANSPORTATION AND STORAGE CONDITIONS
Page 4
A4 –UNPACKING
Page 5
B –INSTALLATION
Page 5
C –SAFETY INSTRUCTIONS
Page 6
D –OPERATION INFORMATION
Page 7
E –CLEANING AND MAINTENANCE
Page 10
F –TROUBLESHOOTING
Page 11
G –EXPLODING DRAWING AND SPARE PART LIST
Page 12
H –ELECTRICAL CIRCUIT DIAGRAM
Page 13

3
A –GENERAL INFORMATION
READ CAREFULLY ALL INSTRUCTIONS AND WARNINGS IN THIS USER MANUAL.
THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE SAFE
INSTALLATION, USE AND MAINTENANCE OF YOUR PRODUCT AND NECESSARY
WARNINGS FOR YOU TO USE THE MOST USEFUL FROM YOUR DEVICE.
KEEP THIS MANUAL IN A SAFE AND EASY REACH FOR FUTURE USE.
THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY DAMAGES TO HUMAN,
ENVIRONMENT, OR OTHER MATERIALS CAUSED BY THE IMPROPER USE OF THE
DEVICE, RESULTING FROM THE TRANSLATION OR EDITION OF THIS BOOKLET.
WILFUL DAMAGE TO DEVICE, OMISSION, AND DAMAGES CAUSED BY NOT
SUITABLE TO INSTRUCTIONS AND REGULATIONS OR WRONG CONNECTIONS
AND UNAUTHORIZED INTERVENTION TO THE DEVICE WILL VOID THE
WARRANTY OF THE PRODUCT.
.

4
A1 –PRODUCT DESCRIPTION
This appliance is a burger machine designed for use in industrial kitchens and recommended
for use by professional users.
A2 –TECHINICAL INFORMATION
Product Code
GGM-BRG01-E15-0001
Dimensions (mm)
400x810x500
Weight (kg)
64
Gross Dimensions (mm)
450x830x640
Gross Weight (kg)
76
Electric Input (V)
230
Cable (mm²)
5x2,5
Power (KW)
6,2
Fuse (A)
3x25
A3 –TRANSPORTATION AND STORAGE CONDITIONS
- The device should be placed in the box vertically.
- If the transport distance is far, it should be moved slowly, if necessary, the device should
be fixed to the pallet against shaking or its balance should be maintained by a person.
- While carrying the product, do not hit or drop it.
- If the product is to be stored before the first use, the original packaging must be stored
unopened.
- If it is to be stored after the device, it must be protected by cleaning and packaging.
- During pallet transport, forklift legs should be placed under the pallet while transported.
You must contact the main body at minimum two points with the forks of the forklift.
Otherwise, the pallet cannot be transported in a balanced way.

5
A4 –UNPAKING
- Please unpack the package according to the security codes and ordinances of current
country and get rid from the pack. Parts which contacts with food are produced by stainless
steel. All plastic parts are marked by material’s symbol.
- Please check that all parts of appliance had come completely and if they are damaged or
not during the shipping.
- After the installation of the device, please throw away of the packaging materials by paying
attention to safety and environmental conditions. For reuse of waste packages, throw them
into the relevant recycling bins according to their properties (foil, cardboard, styrofoam). When
throw away of any electrical equipment, make it unusable by cutting the cable.
B –INSTALLATION
- Installation should be done by a qualified technician according to the instructions. Our
company cannot be held responsible for any damage to people, animals or property due to
incorrect installation.
- In case the device malfunctions, turn off the device. Only a service center authorized by the
manufacturer should service the device. Ask for original spare parts.
- The ground on which the device will be placed must be flat and it must be ensured that the
device operates on a scale. Take necessary precautions against the risk of the product tipping
over.
- Connection to the electrical power supply must be made by a competent person.
- Please be sure that the voltage connected to appliance must be equal with the voltage which
is on appliance’s label.
- The ground connection of the device must be made in accordance with standards and safety
rules.
- The grounding of the device should be connected to the grounding line which is the closest
panel of electrical installation.
- Device electrical connection, main fuse and leakage current fuse must be made in accordance
with the current regulations and rules.
- In places with high electrical noise, an isolation transformer and line filter should be used on
the supply line.
- If more than one electronic device is used, a separate supply line must be installed for each
device.

6
- No control circuit should be connected to the supply line of the device.
- Cables that carry the sensor and input signals to the device should be carried as far as
possible and separately from the supply, control, switched inductive load cables and they
should be prevented from being affected.
- Necessary precautions should be taken to prevent liquid leakage and metal parts to become
conductive into the device. Otherwise, accidents such as fire and electric shock may occur.
C –SAFETY INSTRUCTIONS
- This device must be installed in accordance with current regulations and used only in
a well-ventilated area. Consult instructions for setting up the device and before use.
- The device is made for industrial use and should only be used by personnel trained in
the device.
- Do not interfere with the device without using appropriate protective equipment.
- Keep the device cable away from hot surfaces.
- For the long lasting of the device, never run it idle for a long time. When the device is
not used, it must be turned off. In long-term use, the device should be turned off and
rested for at least 10 minutes every 4 hours.
- All kinds of flammable solid liquid materials (clothes, alcohol and derivatives, petro-
chemical products, wood and plastic materials, curtains, etc.) should never be kept in
the area where the device is operated.
- Because of any reason if there is a fire or flame flare where the appliance is used, turn
off all gas valves and electric contractor switch quickly and use fire extinguisher.Never
use water to extinguish the fire.
- Damages caused by lack of grounding connection will not be covered under warranty.
- Do not use non-original spare parts on the device. In case you use for the device spare
parts not supplied by our company, the device will be out of warranty.

7
D –OPERATION INFORMATION
It should payed attention to warnings as below:
When the device is energized, no button should be touched until the ON / OFF
button lights up.
Information about the touch type is given in figure 1 above.
Figure 1: Touch Alerts

8
Figure 2: Control Paneel
If P1 stage is selected while the device is on, RL1 gives an
output for a preset of 10 seconds. Press button to
change the duration of P1 step.
Hold buttons to change. For registration keep
button pressed.
If P2 stage is selected while the device is on, RL1 gives an
output for a preset of 20 seconds. Press button to
change the duration of P2 step.
Hold buttons to change. For registration keep
button pressed .
If P3 stage is selected while the device is on, RL1 gives an
output for a preset of 30 seconds. Press button to
change the duration of P3 step.
Hold buttons to change. For registration keep
button pressed.

9
RL1 (10A) relay output becomes active when information comes from SW1 input
while the device is on. The relay continues to give an output for the selected time
value. When information comes from SW2 input or STOP button is pressed, the
relay stops giving output directly.
If P4 stage is selected while the device is on, RL1 gives an
output for a preset of 40 seconds. Press button to
change the duration of P4 step.
Hold buttons to change. For registration keep
button pressed .
If P5 stage is selected while the device is on, RL1 gives an
output for a preset of 50 seconds. Press button to
change the duration of P5 step.
Hold buttons to change. For registration keep
button pressed .
If P6 stage is selected while the device is on, RL1 gives an
output for a preset of 60 seconds. Press button to
change the duration of P6 step.
Hold buttons to change. For registration keep
button pressed .
To Change the predetermined times, press the button
And to change time set use buttons.
For recording keep presses.
If the STOP button is pressed while the device is running, the
relay stops giving an output.
It is used for turning the device on and off.

10
E –CLEANING AND MAINTENANCE
Cleaning and maintenance after every use;
Make sure that the plug is not plugged in or the switch is turned off while cleaning the
device.
Clean the surface of the device after each use.
If the device will not be used for a long time, the surfaces should be covered with a thin
layer of Vaseline.
Do not use abrasive cleaning chemicals as these can leave harmful residues.
Do not use pressurized water and steam while cleaning the device.
Do not clean the outer stainless surface of the device with cleaner that can scratch the
material such as wire wool.
Periodic cleaning and maintenance;
Maintenance should be done by qualified person.
Parts that need to be removed during periodic cleaning should be removed and
reassembled by technical service personal.
According to the frequency of use, the electrical maintenance of the device should be done
by spraying dry air after the electrical connection is cut.

11
If any of the security functions are not working, do not use the device and contact our
authorized services.
F –TROUBLESHOOTING
PROBLEM
REASON
HOW TO REMOVE
THE APPLIANCE
DOESN’T
OPERATE
- The device may not be
receiving electricity.
- Circuit breaker may not be
open.
- Check the electrical connection.
- Check the fuse box
connection.
DEVICE STOPPED
- The device may stop due to
low voltage.
- Check the voltage.

12
G –EXPLODING DRAWING AND SPARE PART LIST

13
G –EXPLODING DRAWING AND SPARE PART LIST
BURGER MACHINE
NO
PART NAME
P.CODE
3
BASE FRAME
-
29
BUTTON BUFFER
OMK-YP-00028
30
RED LED
OMK-YP-00029
46
SWITCH
OMK-YP-00045
58
PLASTIC
OMK-YP-00057
59
FEET
OMK-YP-00058
60
ENERGY INPUT
OMK-YP-00059
68
BUTTON APPARAT
OMK-YP-00067
89
BUTTON
OMK-YP-00088
169
MAGNET
OMK-YP-00165
199
THERMOSTAT
OMK-YP-00195
200
BUTTON BUFFER
OMK-YP-00196
289
SWITCH
OMK-YP-00285
290
HANDLE CENTER PIN
OMK-YP-00286
291
HANDLE CENTER RING
OMK-YP-00287
292
VOLAND
OMK-YP-00288
293
BUTTRESS GEAR SHAFT
OMK-YP-00289
294
BUTTRESS GEAR BEARING
OMK-YP-00290
295
ACORN NUT
OMK-YP-00291
296
HANDLE CONNECT
OMK-YP-00292
297
HANDLE LIFT BUTTON
OMK-YP-00293
298
GIGON
OMK-YP-00294
299
HANDLE PIPE
OMK-YP-00295
300
ELEVATION-MIDDLE
OMK-YP-00296
301
POLIAMID FLAKE
OMK-YP-00297
302
REINFORCEMENT PART
OMK-YP-00298
303
SPRING
OMK-YP-00299
304
ELEVATION-FRONT-BACK
OMK-YP-00300
305
SCREW ELEVATION
OMK-YP-00301
306
PIN
OMK-YP-00302
307
RESISTANCE
OMK-YP-00303
308
RING
OMK-YP-00304
309
TENSION SHAFT
OMK-YP-00305
310
TEFLON BAND
OMK-YP-00306
311
TOP TABLE
-
312
LUBRICATOR
-
313
ELECTRONIC CARD
OMK-YP-00307
314
RESISTANCE
OMK-YP-00308
315
PISTON
OMK-YP-00309
316
ELEVATION SHEET
OMK-YP-00310
317
GLASS FIBER
____-
318
HANDLE PIN PIPE
OMK-YP-00311
319
ELEVATION BOLT
OMK-YP-00312

14
H –ELECTRICAL CIRCUIT DIAGRAM
S1
LID SWITCH
T1
BOTTOM THERMOSTAT
T2
TOP THERMOSTAT
M
MAGNET
D
DIODE
L1
BOTTOM THERMOSTAT SIGNAL LAMP
L2
TOP THERMOSTAT SIGNAL LAMP
R1
BOTTOM RESISTANCE GROUP 2X1500 W
R2
TOP RESISTANCE GROUP 2X1500 W