Gigamon GigaVUE-FM Series Installation instructions

GigaVUE-FM
Hardware Appliance
Guide for GFM-HW1-
FM010 and GFM-
HW1-FM001-HW
GigaVUE-FM
Product Version: 5.16
Document Version: 1.0
(See Change Notes for document updates.)

Copyright 2022 Gigamon Inc.. All rights reserved.
Information in this document is subject to change without notice. The software described in
this document is furnished under a license agreement or nondisclosure agreement. No part
of this publication may be reproduced, transcribed, translated into any language, stored in a
retrieval system, or transmitted in any form or any means without the written permission of
Gigamon Inc..
Trademark Attributions
Gigamon and the Gigamon logo are trademarks of Gigamon in the United States and/or
other countries. Gigamon trademarks can be found at www.gigamon.com/legal-
trademarks. All other trademarks are the trademarks of their respective owners.
Gigamon Inc.
3300 Olcott Street
Santa Clara, CA 95054
408.831.4000
Change Notes
When a document is updated, the document version number on the cover
page will indicate a new version and will provide a link to this Change Notes
table, which will describe the updates.
Product
Version
Document
Version
Date
Updated
Change Notes
5.16.00 1.0 05/26/2022 Original release of this document with
5.16.00 GA.

Contents
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-
FM010 and GFM-HW1-FM001-HW 1
Change Notes 2
Contents 3
About your system 7
Front View of the System 7
8 x 2.5-inch drive system 7
Left Control Panel View 8
Status LED indicators 8
Right Control Panel View 9
Back View of the System 9
LCD Panel 11
Viewing Home screen 12
Setup menu 12
View menu 13
Configuring the GigaVUE-FM Appliance 14
Connecting to the Network 14
Configuring to the GigaVUE-FM 14
Powering on the Appliance Manually 15
Logging in to the GigaVUE-FM application from the appliance 15
Accessing the Appliance Remotely 15
Running Configuration Jump Start 17
Upgrade GigaVUE-FM 19
Supported Upgrade Paths for GigaVUE-FM 19
Important GigaVUE-FM Upgrade Guidance 21
Upgrade GigaVUE-FM from the GigaVUE-FM CLI 22
Upgrade GigaVUE-FM from the UI 25
How to Use the Snapshot Feature 29
Installing and Removing System Components 31
Safety instructions 31
Before working inside your system 31
After working inside your system 31
Recommended tools 32
Front Bezel (Optional) 32
Contents 3
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Removing the front bezel 32
Installing the front bezel 32
System cover 33
Removing the system cover 33
Installing the system cover 34
Inside the System 34
Backplane Cover 36
Removing the backplane cover 36
Installing the backplane cover 36
Air Shroud 37
Removing the air shroud 37
Installing the air shroud 38
Cooling Fans 39
Removing the Cooling Fan 39
Installing Cooling Fan 40
Intrusion Switch 40
Removing the Intrusion Switch 41
Installing the intrusion switch 41
Drives 42
Removing a Drive Blank 42
Installing a drive blank 42
Removing a Hard Drive 43
Installing a Hard Drive 44
Removing the Drive from the Drive Carrier 45
Installing a drive into the drive carrier 46
System Memory 47
System memory guidelines 47
Processors and heat sinks 54
Removing Processor and Heat Sink Module 54
Installing a Processor and Heat Sink Module 55
Removing the Processor from the Processor and Heat Sink Module 56
Installing the Processor into a Processor and Heat Sink Module 57
Internal PERC riser 59
Removing the internal PERC riser 59
Installing the Internal PERC Riser 60
Removing the PERC card from the internal PERC riser 61
Installing PERC card into the Internal PERC riser 62
Expansion cards and expansion card risers 63
Expansion Card Installation Guidelines 63
Expansion bus specifications 68
Installing an expansion card riser 69
Removing an expansion card riser 70
Removing the Expansion card from the Expansion Card Riser 71
Contents 4
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Installing the Expansion Card into the Expansion Card Riser 73
M.2 SSD module 75
Installing the M.2 SSD module 75
Removing the M.2 SSD module 76
Optional MicroSD or vFlash card 77
Removing the MicroSD card 77
Installing the MicroSD card 77
Optional IDSDM or vFlash module 78
Removing the Optional IDSDM or vFlash card 78
Installing optional IDSDM or vFlash card 79
LOM riser card 80
Removing the LOM riser card 80
Installing the LOM riser card 81
Hard drive backplane 82
Hard drive backplane details 82
Installing the hard drive backplane 82
Removing the Hard Drive backplane 83
Cable Routing 85
System Battery 86
Replacing the system battery 86
Optional internal USB memory key 88
Replacing the optional internal USB memory key 88
Optical drive (optional) 88
Removing the optical drive 88
Installing the optical drive 89
Power supply units 90
Removing a Power Supply unit blank 90
Installing a Power Supply Unit blank 91
Removing a Power Supply Unit 91
Installing a Power Supply Unit 92
Removing a non-redundant cabled AC power supply unit 93
Installing a non-redundant cabled AC power supply unit 93
Power interposer board 94
Removing power interposer board 94
Installing power interposer board 95
Control panel 96
Removing the left control panel 96
Installing the left control panel 97
Removing the Right Control Panel 97
Installing the right control panel 98
System Board 99
Removing the System Board 99
Installing the System Board 100
Contents 5
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Restoring the system using Easy Restore 102
Manually update the Service Tag 103
Entering the system Service Tag by using System Setup 103
Trusted Platform Module 104
Upgrading the Trusted Platform Module 104
Removing the TPM 104
Installing the TPM 105
Initializing TPM for BitLocker users 105
Initializing the TPM 1.2 for TXT users 105
Jumpers and Connectors 107
System board jumper settings 108
Disabling forgotten password 108
Using System Diagnostics 110
Embedded System Diagnostics 110
Getting Help 112
Contacting Gigamon 112
Locating your system Service Tag 112
Additional Sources of Information 113
Documentation 113
How to Download Software and Release Notes from My Gigamon 115
Documentation Feedback 116
Contact Technical Support 117
Contact Sales 117
Premium Support 118
The Gigamon Community 118
Glossary 119
Contents 6
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

About your system
The GigaVUE-FM Appliance is a 1U, dual socket rack system that supports:
●Two Intel Xeon Scalable Processors
●16 DIMM slots
●8 x 2.5-inch drives.
●Two redundant power supply units (PSU)
The GigaVUE-FM Appliance has two models which are as follows :
■GFM-HW1-FM010 - This model includes a ten node license.
■GFM-HW1-FM001-HW- This model does not include a ten-node license.
Front View of the System
The front view of the chassis displays the following components.
8 x 2.5-inch drive system
Item Ports, panels,
and slots
Icon Description
1 Left control
panel
N/A Contains the system health and system ID, status LED, and the iDRAC
Quick Sync 2 (wireless) indicator.
●Status LED: Enables you to identify any failed hardware components.
There are five status LED’s and an overall system health LED (Chassis
health and system ID) bar. For more information, see the Status LED
indicators section.
2 Optical drive
(Not Installed)
N/A Slot for slim SATA DVD-ROM drive or DVD+/-RW drive.
3 VGA port Enables you to connect a display device to the system.
4
Right control
panel N/A
Contains the power button, USB port, iDRAC Direct micro port, and
the iDRAC Direct status LED.
5 Drive slots N/A Enable you to install drives that are supported on your system.
About your system
Front View of the System 7
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Left Control Panel View
Item Indicator, button, or connector Icon Description
1 Status LED indicators N/A Indicate the status of the system.
2 System health and system ID indicator iIndicates the system health.
Status LED indicators
NOTE:The indicators display solid amber if any error occurs.
Table 5. Status LED indicators and descriptions
Icon Description Condition Corrective Action
Drive indicator The indicator turns solid amber, if there
is a drive error.
●Check the System event log to
determine if the drive has an error.
●Run the appropriate Online
Diagnostics test. Restart the system,
and run embedded diagnostics
(ePSA).
●If the drives are configured in a
RAID array, restart the system, and
enter the host adapter configuration
utility program.
Temperature
indicator
The indicator turns solid amber, if the
system experiences a thermal error (for
example, the ambient temperature is
out of range or there is a fan failure).
Ensure that none of the following
conditions exist:
●A cooling fan has been removed or
has failed.
●System cover, air shroud, or back
filler bracket is removed.
●Ambient temperature is too high.
●External airflow is obstructed.
About your system
Left Control Panel View 8
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Icon Description Condition Corrective Action
Electrical
indicator
The indicator turns solid amber, if the
system experiences an electrical error
(for example, voltage out of range, or a
failed power supply unit (PSU) or voltage
regulator).
Check the System event log or
system messages for the specific
issue. If it is due to a problem with
the PSU, check the LED on the PSU.
Reseat the PSU.
Memory
indicator
The indicator turns solid amber if a
memory error occurs.
Check the System event log or
system messages for the location of
the failed memory. Reseat the
memory module.
PCIe indicator The indicator turns solid amber, if a PCIe
card experiences an error.
Restart the system. Update any
required drivers for the PCIe card.
Reinstall the card.
Right Control Panel View
Table 8. Right control panel
Item Indicator or Button Icon Description
1 Power button Indicates if the system is powered on or off.
Press the power button to manually power
on or off the system.
Press the power button to gracefully shut
down an ACPI-compliant operating system.
2 USB port The USB ports are 4-pin, 2.0- compliant.
This port enables you to connect USB
devices to the system.
3 iDRAC Direct LED N/A The iDRAC Direct LED indicator lights up to
indicate that the iDRAC Direct port is
actively connected to a device
4 iDRAC Direct port (Micro-AB USB) The iDRAC Direct (Micro- USB) AB USB)
port enables you to access the iDRAC
Direct (Micro-AB) features.
Back View of the System
The back view displays the features available on the back of the system.
About your system
Right Control Panel View 9
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Item Ports, panels, or slots Icon Description
1 Serial port Use the serial port to connect a
serial device to the system.
2 iDRAC9 dedicated network port N/A Use the iDRAC9 dedicated network
port to securely access the
embedded iDRAC on a separate
management network.
3 Ethernet ports (2) Use the Ethernet ports to connect
Local Area Networks (LANs) to the
system.
4 Low profile riser right slot N/A Use the card slot to connect half-
height PCIe expansion card on low
profile riser.
5 Low profile riser left slot N/A Use the card slot to connect half-
height PCIe expansion card on low
profile riser.
6 Power supply unit (PSU) N/A For more information about the PSU
configurations, see the PowerEdge
R440 Technical Specs.
7 Power supply unit (PSU) N/A For more information about the PSU
configurations, see the PowerEdge
R440 Technical Specs.
8 USB 3.0 port (2) Use the USB 3.0 port to connect USB
devices to the system. These ports
are 4-pin, USB 3.0-compliant.
About your system
Back View of the System 10
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Item Ports, panels, or slots Icon Description
9 VGA port Use the VGA port to connect a
display to the system.
10 System status indicator cable port N/A Enables you to connect the status
indicator cable and view system
status when the CMA is installed.
11 System identification button Press the system ID button:
●To locate a particular system
within a rack.
●To turn the system ID on or off. To
reset iDRAC, press and hold the
button for more than 15 seconds.
NOTE: To reset iDRAC using system
ID, ensure that the system ID button
is enabled in the iDRAC setup.
LCD Panel
The LCD panel provides system information, status, and error messages to indicate if the
system is functioning correctly or requires attention. The LCD panel can also be used to
configure or view the system’s iDRAC IP address.
The LCD panel is available only on the optional front bezel. The optional front bezel is hot
pluggable. The statuses and conditions of the LCD panel are outlined here:
●The LCD backlight is white during normal operating conditions.
●When the system needs attention, the LCD backlight turns amber, and displays an error
code followed by descriptive text.
NOTE:If the system is connected to a power source and an error is detected, the
LCD turns amber regardless of whether the system is turned on or off.
●When the system turns off and there are no errors, LCD enters the standby mode after five
minutes of inactivity. Press any button on the LCD to turn it on.
●If the LCD panel stops responding, remove the bezel and reinstall it.
●The LCD backlight remains off if LCD messaging is turned off using the iDRAC utility, the
LCD panel, or other tools.
About your system
LCD Panel 11
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Item Button or
display
Description
1 Left Moves the cursor back in one-step increments.
2 Select Selects the menu item highlighted by the cursor.
3 Right Moves the cursor forward in one-step increments. During message scrolling:
● Press and hold the right button to increase scrolling speed.
● Release the button to stop.
The display stops scrolling when the button is released. After 45 seconds of
inactivity, the display starts scrolling.
4 LCD display Displays system information, status, and error messages or iDRAC IP address.
Viewing Home screen
The Home screen displays user-configurable information about the system. This screen is
displayed during normal system operation when there are no status messages or errors.
When the system turns off and there are no errors, LCD enters the standby mode after five
minutes of inactivity. Press any button on the LCD to turn it on.
1. To view the Home screen, press one of the three navigation buttons (Select, Left, or
Right).
2. To navigate to the Home screen from another menu, complete the following steps:
a. Press and hold the navigation button until the up arrow is displayed.
b. Navigate to the Home icon using the up arrow .
c. Select the Home icon.
d. On the Home screen, press the Select button to enter the main menu.
Setup menu
NOTE:When you select an option in the Setup menu, you must confirm the option
before proceeding to the next action.
About your system
LCD Panel 12
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Option Description
iDRAC Select DHCP or Static IP to configure the network mode. If Static IP is selected, the available
fields are IP, Subnet (Sub), and Gateway (Gtw). Select Setup DNS to enable DNS and to view
domain addresses. Two separate DNS entries are available
Set error Select SEL to view LCD error messages in a format that matches the IPMI description in the
SEL. This enables you to match an LCD message with an SEL entry. Select Simple to view
LCD error messages in a simplified user-friendly description.
Set home Select the default information to be displayed on the Home screen. See View menu for the
options and option items that can be set as the default on the Home screen.
View menu
NOTE:When you select an option in the View menu, you must confirm the option
before proceeding to the next action.
Option Description
iDRAC IP Displays the IPv4 or IPv6 addresses for iDRAC9. Addresses include DNS (Primary and
Secondary), Gateway, IP, and Subnet (IPv6 does not have Subnet).
MAC Displays the MAC addresses for iDRAC, iSCSI, or Network devices.
Name Displays the name of the Host, Model, or User String for the system.
Number Displays the Asset tag or the Service tag for the system
Power Displays the power output of the system in BTU/hr or Watts. The display format can be
configured in theSet home submenu of the Setup menu.
Temperature Displays the temperature of the system in Celsius or Fahrenheit. The display format can be
configured in the Set home submenu of the Setup menu.
About your system
LCD Panel 13
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Configuring the GigaVUE-FM
Appliance
This section provides the procedures for making the physical connections to the appliance
and how to access and configure the GigaVUE-FM application after the appliance is
powered up.
Connecting to the Network
After installing the GigaVUE-FM Appliance, you will need to connect to your management
switch or switches to access to the GigaVUE-FM application and use iDRAC for managing
the appliance remotely.
Prerequisites
■Ethernet cables
Connecting to GigaVUE-FM
1. Locate Ethernet connector 1 on the rear panel and plug in the Ethernet cable. This is
used for eth0.
2. Connect the other end of the cable to the management switch.
3. Locate the iDRAC port on the back panel and plug in the second Ethernet cable.
4. Connect the second Ethernet cable to the same management switch. You can connect
to a different management switch if you want to access iDRAC from a different subnet.
5. Connect the peripherals to the appliance if you plan to configure the GigaVUE-FM
application locally.
6. Power on the appliance manually if you will use the peripherals connected to the
appliance to configure the GigaVUE-FM application.
7. Remote power on can be done through iDRAC.
Configuring to the GigaVUE-FM
You can configure the GigaVUE-FM application that is pre-installed on the appliance by
connecting peripherals to the appliance and powering it on. Once the appliance is powered
on you can log in to GigaVUE-FM and run the configuration jump-start program.
NOTE:The USB ports on the front panel of the GigaVUE-FM Appliance are disabled.
Configuring the GigaVUE-FM Appliance
Connecting to the Network 14
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

1. Connect the mouse and key board to the USB ports on rear panel.
2. Connect the monitor to the video connector on the rear panel.
NOTE:Use this procedure if you want to configure the GigaVUE-FM application
directly from the appliance.
Powering on the Appliance Manually
The following procedure is used to manually power on the appliance. You can also power on
the appliance through iDRAC.
1. Remove the front bezel.
2. Press the power button located in the upper-left corner of the front panel.
3. Replace the front bezel.
4. Log.
Logging in to the GigaVUE-FM application from
the appliance
1. Power on the appliance. See Powering on the Appliance Manually. The appliance will boot
up and load the software. When it is completed, you will see the login screen for GigaVUE-
FM.
2. At the login prompt, enter admin.
3. When the system prompts for a password, enter admin123A!!
The system will automatically run the configuration jump-start script the first time you log
in.
Accessing the Appliance Remotely
You can manage the GigaVUE-FM appliance remotely through iDRAC. iDRAC is always
available where there is power to the system. This allows you to power on/off the host and
connect through the Integrated Remote Access Controller UI with a Web browser. Before
you can access the appliance remotely, you need the iDRAC IP address.
1. Locate the LCD display on the front panel.
2. Click the Select button.
3. When you see the Home icon, click the Right button to select the View menu.
4. Click the Select button to choose the iDRAC menu.
Configuring the GigaVUE-FM Appliance
Logging in to the GigaVUE-FM application from the appliance 15
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

5. Click the Select button to choose IPv4.
6. Record the IPv4 address.
Powering on the Appliance through iDRAC
The following is the procedure for powering on the appliance through the iDRAC connect.
This allows you to power on/off the device remotely.
1. Log in to the iDRAC interface.
a. Open a Chrome browser and enter the IP address in the URL field. The following
screen displays in the browser.
b. Enter the default username and password (root, admin123A!).
c. Click Submit.
a. Enter the default username and password (root, admin123A!).
NOTE:It is highly recommended that you change the default password.
2. The Integrated Remote Access Controller displays.
Configuring the GigaVUE-FM Appliance
Logging in to the GigaVUE-FM application from the appliance 16
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Running Configuration Jump Start
This section describes the configuration jump-start script that runs the first time you log in
to GigaVUE-FM. After running the configuration script, you can log in to the GigaVUE-FM UI
from a Web browser or a remote console such as TeraTerm or PuTTY to use the command
line interface (CLI) to re-run jump-start or use other CLI commands.
The following are the steps in the configuration jump-start and an explanation of each step.
■Hostname?
Provide a unique hostname for GigaVUE-FM. The hostname may contain letters, numbers,
periods (.), and hyphens (-), but may not begin with a hyphen. No other special characters
are permitted. This will also appear as part of the command line prompt after jump-start
completes.
■Use DHCP on eth0 interface?
The default for this step in the configuration is no. If you answer yes. GigaVUE-FM acquires
the DHCP address from the local server.
■Primary IP address and masklen?
Select Yes or No to mask you Primary address.
■Default gateway?
Provide the default gateway address for reaching the management domain.
Configuring the GigaVUE-FM Appliance
Running Configuration Jump Start 17
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

■Primary DNS server?
Provide the default gateway address for reaching the management domain.
■Domain name?
Enter a domain name to use instead of the IP address to open the GigaVUE-FM login page.
For example, fmappliance.com.
■Admin password?
This sets the password for the admin user in GigaVUE-FM, which you will use to log in to for
the first time. The default is admin123A!. It is highly recommended that you change the
default password.
■Additional Domain Name Server IP addresses?
Enter the address of any additional name servers required. This must be provided as a set of
IP addresses with spaces. For example, 10.10.10.10 11.11.11.11.
■Additional DNS Domains?
You can add multiple DNS domains by entering the names configuration with spaces. For
example, abc.com def.com.
■Enable NTP?
If you respond yes to this option, you will be asked to provide the address of an NTP server
and its NTP version number.
When you have completed the steps in the configuration jump-start, you can change any of
the configurations by entering the step number. Otherwise, press enter to complete the
configuration.
After configuration is complete, you can log in to the GigaVUE-FM application by going to
your Web browser and entering the IP address specified during configuration jump-start in
the URL field. When the GigaVUE-FM login page opens, enter admin in the user name field
and the password you entered in step 7 of the configuration jump-start.
Configuring the GigaVUE-FM Appliance
Running Configuration Jump Start 18
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Upgrade GigaVUE-FM
This section describes how to upgrade GigaVUE-FM to the latest revision in either a VMware
ESXi host or in Microsoft HyperV environment.
Before you upgrade, read Important GigaVUE-FM Upgrade Guidance for special
guidelines and caveats related to upgrading from specific versions of GigaVUE-FM.
At a high level, the upgrade process involves the following steps:
1. Before starting an upgrade to GigaVUE-FM, get the latest image, upgrade information,
and Release Notes from the Software & Release Notes download page (login required)
on the Gigamon Community.
2. Be sure to review the GigaVUE Release Notes for the latest release before performing
the upgrade.
lEnsure your environment supports any specified system requirements.
lCheck the minimum memory requirements in the new release as they may change
between releases.
3. Once the GigaVUE-FM image is obtained, download it to a server within your
environment. This must be a server that your current GigaVUE-FM instance can access
to upload it.
4. (Important) Save your current configuration using the facilities provided by the
hypervisor before upgrading.
5. Verify that the GigaVUE-FM instance time is set correctly to ensure accuracy of the
trending data that is captured.
6. Perform the upgrade using either the Command-Line Interface (CLI) or the GigaVUE-
FM User Interface (UI).
7. After upgrading your GigaVUE-FM instance, upgrade your GigaVUE-VM deployments.
Refer to “Bulk Upgrading GigaVUE-VM Nodes” in the GigaVUE Cloud Suite for
VMware—GigaVUE V Series Guide.
Upgrade Methods:
■Upgrade GigaVUE-FM from the GigaVUE-FM CLI
■Upgrade GigaVUE-FM from the UI
■How to Use the Snapshot Feature
Supported Upgrade Paths for GigaVUE-FM
The supported upgrade paths for GigaVUE-FM is as follows:
o5.8.01 > 5.10.02 > 5.11.01*
Upgrade GigaVUE-FM 19
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

o5.9.01 > 5.11.01*
o5.10.02 > 5.11.01*
o5.10.02 > 5.12.01**
o5.11.01 > 5.12.01**
o5.11.01 > 5.13.00**
o5.12.01 > 5.13.00**
o5.12.01 > 5.13.01**
o5.13.00 > 5.13.01**
o5.12.01 > 5.14.00**
o5.13.00 > 5.14.00**
o5.13.01 > 5.14.00**
o5.13.01 > 5.15.00**
o5.14.00 > 5.15.00**
o5.14.00 > 5.16.00**
o5.15.00 > 5.16.00**
*Password change is mandated for all passwords during upgrade.
**Password change is only mandated if the current password is using the default
password.
GigaVUE-FM Upgrade Rules and Notes
lBest Practice: Always upgrade your GigaVUE-FM instance before upgrading the
GigaVUE-OS nodes. You can upgrade the attached nodes from the device or from
GigaVUE-FM. The latter is recommended. Refer to “Upgrading Software on a GFM-HW1-
FM010,GFM-HW1-FM001-HW Node or a Cluster from GigaVUE-FM” in the GigaVUE
Fabric Management Guide.
lIf upgrading from GigaVUE-FM versions lower than 5.10.xx: You cannot directly
upgrade your GigaVUE-FM instance to release 5.10.00 from a release prior to 5.8.xx. If your
current version of GigaVUE-FM is 5.7.xx or lower and you want to upgrade to software
version 5.13.xx, you must first migrate to GigaVUE-FM5.10.xx and then upgrade to 5.11.xx.
NOTE:For instructions on how to migrate refer to Migrate GigaVUE-FM in
GigaVUE 5.10 Documentation.
lIf upgrading from GigaVUE-FM versions lower than 5.5.00: While upgrading from any
version lower than 5.5.00, an association of more than one VPort to the same GigaSMART
group needs to be removed for any existing GTP GigaSMART operation.
Upgrade GigaVUE-FM 20
GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW