Gigaset 5015 User manual

Gi
gase
t
5015
/
IM
en-
f
r-ru-
h
r
/
A30350
-
M208
-
A801
-
7
-
UP19
/
5015
.
f
m
/
23
.
02
.
2011
1
EN
Gigaset 5015 Quick Guide
Keys
1 Repertory keys
2 Last number redial key
3 Recall key
4Mutekey
5Shiftkey
6Quietkey
7 Loudspeaker key (handsfree)
8Loudkey
9Setkey
10 Lock key
11 Reset key (call duration)
12 Pause key
Display symbols
PIn setting mode
‡Shift key pressed
--- Ready for use
yMicrophone off
oEntry mark when setting (e.g. volume)
u Recall key pressed
P Pause
z
No memory content
---- PIN entry
zzzz
Telephone locked
0 – 9 Phone number
With tone dialling:
n – *key pressed
- – #key pressed
With additional services from public network providers:
ëCall waiting
™Call forwarding immediately
˜Call forwarding on no reply
—Call forwarding when busy
Safety precautions
When installing, connecting and operating the telephone,
always observe the following precautions:
◆Only use the plugs and leads supplied.
◆Only connect the connecting lead to the socket/jack
provided for that purpose.
◆Only connect approved accessories.
◆Arrange the connecting lead where it will not cause
accidents.
◆Position the telephone on a non-slip surface.
◆For your safety and protection, the telephone must not
be used in bath or shower rooms (wet locations).
The telephone is not splash proof.
◆Never expose the telephone to sources of heat, direct
sunlight or other electrical devices.
◆Protect your telephone from moisture, dust, corrosive
liquids and vapours.
◆Never open up the telephone yourself.
◆Do not touch the plug contact with pointed or metallic
objects.
◆Do not carry the telephone by the leads.
◆If you give your Gigaset 5015 to someone else, make
sure you also give them the user guide.
1
23
45
6
7
8
1211109

Gi
gase
t
5015
/
IM
en-
f
r-ru-
h
r
/
A30350
-
M208
-
A801
-
7
-
UP19
/
5015
.
f
m
/
23
.
02
.
2011
2
EN
All electrical and electronic equipment must be disposed of
separately from general household waste using the sites
designated by local authorities.
If a product displays this symbol of a crossed-out rubbish bin,
the product is subject to European Directive 2002/96/EC.
The appropriate disposal and separate collection of used equipment
serve to prevent potential harm to the environment and to health.
They are a precondition for the re-use and recycling of used electrical
and electronic equipment.
For further information on disposing of your used equipment, please
contact your local authority or your refuse collection service.
Preparing the telephone for use
Recommended installation of telephone
◆Do not expose the telephone to direct sunlight or other
sources of heat.
◆Operate at temperatures between +5°C and +40°C.
◆Maintain a distance of at least one metre between the
telephone and radio equipment, e.g. wireless
telephones, wireless pagers or TV sets. Otherwise,
telephone communication could be impaired.
◆Do not install the telephone in dusty areas as this can
shorten the service life of the telephone.
◆To clean, wipe with a moist or antistatic cloth only, never
with a dry cloth (risk of electrostatic charging and
discharge) or harsh cleaning agent.
◆Furniture lacquer and polish can be damaged by contact
with parts of the unit (e.g. device feet).
Connecting
Insert the short end of the coiled handset cord in the socket
provided in the handset and the long end in the socket
marked with an aon the underside of the device. Plug the
phone cord into the outlet on the wall and the other end
into the socket marked with a Yon the underside of the
device. Then your telephone is ready to use.
Making calls
Dialling a number
co Lift handset, dial number.
Any digits after the 20th digit are moved from right to left in
the display. The Pause key <can be used to insert pauses
when dialling, starting from the 2nd digit.
Last number redial (one of the last 5 call numbers)
The last 5 different call numbers dialed are automatically
saved (max. 32 digits each).
cLift handset (or press the Loudspeaker key L
until the dialling tone is audible).
;...;Press the Redial key repeatedly until the
required call number appears with the place
number (1...5 on the left).
oEnter the place number (1...5).
The relevant call number is redialed.
Dialling using the repertory keys
cLift handset (or press the Loudspeaker key L
until the dialling tone is audible). (If necessary,
press =for a 2nd level repertory key).
:Press repertory key.

Gi
gase
t
5015
/
IM
en-
f
r-ru-
h
r
/
A30350
-
M208
-
A801
-
7
-
UP19
/
5015
.
f
m
/
23
.
02
.
2011
3
EN
Saving numbers
Different telephone settings must be completed with the
Set key ?so that they are available permanently.
In order to cancel without saving, e. g. after an incorrect
entry, replace the handset instead of pressing ?at the
end. The original setting is then retained.
Saving with notebook function
You can also save phone numbers during a conversation
with the notebook function.
Saving repertory numbers
You can save up to 20 phone numbers (or even functions,
see page 6) on both levels of the repertory keys.
c? Lift handset, press the Set key. (For 2nd mem-
ory level, also press =.)
:Press the repertory key under which you want
to save the repertory number.
A number that has already been saved is
shown in the display. If the memory for this
repertory key is empty,
z appears in the display
o Enter the number to be saved (up to 32 digits).
or ...
Saving from the redial list:
;...;Press the Redial key repeatedly until the
desired phone number is displayed on the
screen.
?a Press the Set key. Replace handset.
Pressing <allows you to save pauses (not at the 1st digit).
After the 20th digit, any following digits are moved from
right to left in the display.
Delete all repertory numbers
c?1251
Lift handset, initiate function.
?a Press the Set key. Replace handset.
Adjusting the telephone
Adjusting the ringer volume
The volume of the ringer can be set to one of 7 levels and
can also be deactivated completely (default setting: level 7,
highest level) or deactivated completely. When the ringer is
deactivated an incoming call is notified in the display only.
◆To adjust when the telephone is idle:
c?5 Lift handset, initiate function.
H...IAdjust the volume with the Loud/Quiet key.
?a Press the Set key. Replace handset.
◆To adjust while the telephone is ringing:
Press H...Ibefore lifting the handset.
The last value set is saved.
Setting the ringer frequency
The frequency (speed) of the ringer can be set to one of
three levels (default setting: level 3).
c?6 Lift handset, initiate function.
1...3Press one of the keys 1...3:
1: highest frequency; 3: lowest frequency.
?a Press the Set key. Replace handset.
Setting the ringtone
Ten different ringtones can be set for the ringer (default
setting: ringtone 0).
c?7 Lift handset, initiate function.
0...9Press one of the keys 0 ... 9
?a Press the Set key. Replace handset.
Setting the handset volume
The volume on the handset can be set to one of 3 levels and
saved (default setting: level 1).
c?9 Lift handset, initiate function.
H...IAdjust the volume with the Loud/Quiet key.
?a Press the Set key. Replace handset.
Mute
You can deactivate the telephone's handset and
microphone. Then the other party can no longer hear you.
JDuring a call: Press the Mute key
Activate: Press the key again.

Gi
gase
t
5015
/
IM
en-
f
r-ru-
h
r
/
A30350
-
M208
-
A801
-
7
-
UP19
/
5015
.
f
m
/
23
.
02
.
2011
4
EN
Adjusting the loudspeaker
While in handsfree mode, you can set the volume to one of
7 levels and save it (default setting: 7).
H...IAdjust the volume with the Loud/Quiet key.
Activating/deactivating open listening
The built-in loudspeaker means anyone in the room can lis-
ten-in on a call.
LDuring a call:
press the Loudspeaker key.
To deactivate open listening: press the key
again.
When the loudspeaker is activated and the handset is
lifted,open listening is activated. The handsfree micro-
phone is switched off.
When the loudspeaker is activated and the handset is
replaced, handsfree talking via the handsfree microphone
is activated.
Activating/deactivating handsfree mode
With this telephone you can also make calls without lifting
the handset. The optimum distance for speaking into the
microphone is around 50 cm.
◆Activating via the handset during a call:
L+ aReplace the handset while pressing the Loud-
speaker key.
◆Activating before dialling a phone number
LBefore you dial: press and hold the Loud-
speaker key until the dialling tone is audible.
Deactivating handsfree mode:
cLift the handset during a call.
Activating/deactivating the mute melody
You can activate and deactivate the mute melody for the
mute (default setting: on).
c?19#
Lift handset, initiate function.
0/10: deactivate; 1: activate.
?a Press the Set key. Replace handset.
Baby call (direct call) number setting
If a phone number is set for the Baby Call function, it is
dialled automatically when the telephone is locked after
you lift the handset (or press the Loudspeaker key) and
press any key (except ?, M, L, Hand I). The
telephone does not allow other phone numbers to be
dialled, but incoming calls can be received.
c?M8
Lift handset, initiate function.
oEnter the PIN (default setting: 0000).
Activating
oEnter direct call number (max. 32 digits; not
<for pause function!).
or ...
Deleting
;Press the Last number redial key.
?a Press the Set key. Replace handset.
Locking/unlocking the telephone
Only the Baby call number can be dialed when the tele-
phone is locked.
c?M Lift handset, then start the function.
1or 20: unlock; 1: lock
oEnter the PIN (default setting: 0000).
?a Press the Set key. Replace handset.
If the telephone is locked, the display shows
zzzz
.
Temporarily deactivating the telephone lock (for one call)
cMo Lift the handset, press the lock key, enter the
PIN (default setting: 0000).
oDial a call number.
The telephone lock is active again when the handset is
replaced.
Locking/unlocking repertory numbers so they cannot
be changed
c?M6
Lift handset, initiate function.
(If necessary, press =in order to lock/unlock
the repertory key on the 2nd level.)
oEnter the PIN (default setting: 0000).
0 / 10: Repertory keys not locked
1: Repertory keys locked.
?a Press the Set key. Replace the handset.

Gi
gase
t
5015
/
IM
en-
f
r-ru-
h
r
/
A30350
-
M208
-
A801
-
7
-
UP19
/
5015
.
f
m
/
23
.
02
.
2011
5
EN
Changing the PIN
c?M9
Lift handset, initiate function.
oEnter the current PIN (default setting: 0000).
oEnter a new PIN (four digits).
oEnter the new PIN again to confirm.
?a Press the Set key. Replace the handset.
Call duration display
The telephone can display the approximate call duration in
the display (up to 99 min. 59 sec.). If the call duration dis-
play is activated, the time display begins 12 seconds after
the last digit is dialled.
Resetting the counter
After dialling the first digit or at any point during a call:
NPress the Reset key.
The counter goes back to 0 min. 0 sec.
Deactivating/activating
The call duration display is activated by default.
c?18#
Lift handset, initiate function.
0/10: deactivate; 1: activate.
?a Press the Set key. Replace handset.
Setting the pause time
If necessary, the pause time of the Pause key <(pause
function from second input position) can be changed to 1,
3 or 6 seconds (default setting: 3 seconds).
c?102
Lift handset, initiate function.
0...20: 1 sec.; 1: 3 sec.; 2: 6 sec..
?a Press the Set key. Replace handset.
Changing the dialling mode
c?# Lift handset, initiate function.
1/21: Tone dialling.
2: Pulse dialling without flash function.
?a Press the Set key. Replace handset.
Changing dialling modes during a call
If your telephone is set to pulse dialling and you want to use
functions that require tone dialling (e.g. remote access to
an answering machine), you can change the dialling mode
during a call.
*With an open connection: press the star key.
oEnter digits for remote control/data transfer.
The telephone is reset to the original dialling mode by hang-
ing up the handset.
Operation on a PABX
Enter/delete an external line prefixe
If you are using your telephone on a PABX, you may have to
save one or more external line prefixes. A dialling pause is
set automatically with the external line prefixe. You can save
up to three external line prefixes.
c?0 Lift handset, initiate function.
If no external line prefixe has been set in a
location,
z appears in the display.
If several external line prefixes are saved, these
are displayed next to one another; the current
external line prefixe to be edited flashes.
If necessary, use the ;key to toggle
between the external line prefixes displayed,
to edit them as follows:
To delete an external line prefix:
?a Press the Set key. Replace handset.
To enter an external line prefixe:
oEnter a one- to three-digit code.
Enter additional external line prefixes:
;oPress the Last number redial key, enter next
external line prefixe.
?a Press the Set key. Replace handset.
Recall key (on a PABX)
During an external call, you can make a recall or divert the
call. To do this, press the Recall key >. The subsequent
procedure depends on your PABX. By default, the Recall key
is preset to a flash time (interruption time) of 90 ms for use
of new features on public telephone systems. With a
connection to a PABX, it may be necessary to change the
flash time (e.g. 600 ms). To do this, please refer to the
operating instructions for your PABX.