Gigaset Gigaset DA610 User manual

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
overv
i
ew.
f
m
/
23.04.2012
en fr fa ar 1
1110-01
Overview Gigaset DA610
Display and keys
1 Display (£page 4)
2 Control key (£page 5)
3 Speed dial key
4Setkey
5 Redial/pause key
6Recallkey
7Mutekey
8 Star key, selecting/deselecting the ring tone (press and hold)
9 Hash key, selecting/deselecting the key lock (press and hold)
10 Hands-free key
11 Keys for setting the volume of the handset, speaker and ring tone
12 Microphone for hands-free use
LED
@Hands-free key
¤flashes on incoming call
¤lights up when the call is transferred to the speaker
12
1
11
8
10
5
9
4
6
7
2
3

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
overv
i
ew.
f
m
/
23.04.2012
2en fr fa ar
1110-01
Connecting the telephone
¤Connect the telephone connector (1) to
the main telephone socket. Use the tele-
phone cable supplied.
You may need a phone adapter depending
on your country. This is provided in most
cases.
Power is supplied over the telephone line.
A mains adapters is not necessary.
¤Guide the cable through the cable
channel (2).
3
1
¤Connect the handset to the telephone
using the coiled cable (3).
First use
1 Lift the handset for 5 seconds and place it back in the cradle.
2 Lift the handset again. You will hear the free tone and the device is now ready to be used.
Please note:
The phone is connected to the power source via the phone line. In case of a power cut (e.g. if the PABX is switched off at night), the above mentioned
steps need to be repeated. Phonebook entries and speed dialling destinations are stored indefinitely.
The device is designed to be used as a single-line system (on the main extension or a telephone system). It cannot be operated as a second phone
on a line splitter.
Operation on a PBX:
The private branch exchange (PBX) must supply the phone with continuous DC voltage, even when ringing. If this is not the case, the phone may
switch off briefly when ringing. As a result, saved information may be lost. Refer to the operating manual for your PBX for information in this regard
or contact the manufacturer.
2

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
DA
610
IVZ
.
f
m
/
23.04.2012
en fr fa ar 3
1110-01
Table of contents
Overview Gigaset DA610 . . . . . . . . . . . . . . . . . . . . 1
Connecting the telephone . . . . . . . . . . . . . . . . . . 2
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting up the telephone for use . . . . . . . . . . . . . 4
Operating the telephone . . . . . . . . . . . . . . . . . . . . 4
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Writing and editing names and numbers . . . . . . . . . . . . . . . . . . . 5
Text input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Telephoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using open listening / hands-free . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Settings during a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the phonebook . . . . . . . . . . . . . . . . . . . . . . . 7
Using the call list (CLIP) . . . . . . . . . . . . . . . . . . . . . . 8
Using speed dialling numbers. . . . . . . . . . . . . . . . 8
Adjusting the telephone . . . . . . . . . . . . . . . . . . . . 8
Changing the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the handset volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Security settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Locking the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Emergency calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Direct calling (baby call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Blocking numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Network services . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Caller display (CLIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting up a dialling code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation on a PABX . . . . . . . . . . . . . . . . . . . . . . . 11
Special functions/Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the dialling mode/flash time . . . . . . . . . . . . . . . . . . . . 11
Setting dialling prefixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Standard characters . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Questions and answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
4en fr fa ar
1110-01
Safety precautions
When installing, connecting and operating the telephone, always
observe the following precautions:
uOnly use the jacks and leads supplied.
uOnly connect the connecting lead to the intended socket.
uOnly connect the approved accessories
uLay the connecting lead where it will not cause accidents.
uPosition the telephone on a non-slip surface.
uFor your safety and protection, the telephone may not be used in the
bath or shower rooms (wet locations). The telephone is not splash
proof.
uNever expose the telephone to sources of heat, direct sunlight or
other electrical devices.
uProtect your telephone from moisture, dust, corrosive liquids and
vapours.
uNever open up the telephone yourself.
uDo not touch the plug contact with pointed or metallic objects.
uDo not carry the telephone by the leads.
uIf you give your Gigaset DA610 to someone else, make sure you also
give them the operating manual. Your Gigaset DA610 has a perma-
nent memory, so you may want to delete any stored numbers before
passing it on.
Setting up the telephone for use
Recommended installation of telephone:
uDo not expose the telephone to direct sunlight or other sources of
heat.
uOperate at temperatures of between + 5° C and + 40° C.
uMaintain a distance of at least one metre between the telephone
and radio equipment, e.g. radio telephones, radio paging equip-
ment or TV sets. Otherwise telephone communication could be
impaired.
uDo not install the telephone in dusty rooms as this can limit the serv-
ice life of the telephone.
uFurniture lacquer and polish can be adversely affected by contact
with parts of the unit (e.g. feet).
Operating the telephone
The keypad and the display are available to operate your Gigaset DA610.
All usage possibilities are described in the handbook.
Display
Depending on the operating situation the display shows different infor-
mation, e.g. date and time. You can set the date and time and the format
in which they are displayed (£page 9).
Symbols provide information on the status of your telephone.
Display symbols
01 Number of an entry in the phonebook or a call list or of a
speed dial key
oSetting mode activated
fFlashes for a new entry in the call list if the caller's number
transmission (CLIP) is active (£page 11)
gPhonebook open
iKey lock activated
xRinger switched off
mMute mode activated
lFlashes on incoming VIP call
Is indicated if at least one entry with activated VIP mode is
present in the phonebook (£page 7).
Display language
On delivery the display language is set to English. Other languages are
available and you can change the language if you wish (£page 8).
Note
Some of your telephone's functions may only be available without
restriction if they are supported by your and the caller's network pro-
vider, e. g. functions for which information on the caller's telephone
number is required.
This applies for the following functions, for example:
uDisplaying the number of an incoming call (£page 6)
uIndicating a caller with VIP melody (£page 6)
uCall list (£page 8)
Symbol bar: status, date
and time
Display of call duration,
numbers, names, phone-
book and list entries,
settings
m
18:30 01
oi
24.12
01--28
x
Z
f
l

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
en fr fa ar 5
1110-01
Control key
You activate the functions and navigate the menus using the control
key. The functions offered depend on the operating situation.
Writing and editing names and numbers
Text input
~Enter text using the keypad.
Multiple letters and numbers are assigned to each key between
and Oand Q, *and #. You enter a specific character
by pressing the corresponding key several times.
You will find a table of applicable characters in the Appendix £page 12.
Moving the cursor
t s To move the cursor to the left/right in the text, press the
control key upwards/downwards.
Deleting/correcting characters
XPress the left-hand side uof the control key. The char-
acter to the left of the cursor is deleted. Press and hold
down to delete the whole line.
Telephoning
In addition to the handset, you can also call using the speaker (hands-
free function). In the following instructions, the symbol calso always
stands for @.
Making a call
Entering the telephone number using the keypad
c ~ Lift the handset, dial the number.
Instead of lifting the handset:
@Press the hands-free key to make a call via the speaker.
You can switch over at any time during the conversation.
Dialling from the phonebook
If you have already saved numbers in your phonebook (£page 7), you
can make a call directly from the phonebook.
ZOpen the phonebook using the control key s.
Searching for an entry
qSelect an entry.
or
~Enter letters (£page 5). The first entry starting with this
letter is displayed.
Dialling numbers
cLift the handset.
or
[Open the context menu.
qSelect DIAL ENTRY and confirm with [.
The call is initiated via the speaker. To make the call using
the handset, simply lift the handset.
In standby:
tYOpen the call list
sZOpen phonebook
t
s
In lists:
Scrolls one entry upwards/downwards.
Hold down: Scrolls the list fast upwards/downwards.
While editing time setting:
Moves forwards/backwards one position.
uIn menus and lists: Exits the menu or list.
While editing names and numbers:
Deletes the character to the left of the cursor.
Hold down: Deletes the line.
If the entry is empty: Exits the editing mode.
vPhone number entered: Dials the phone number.
In lists: Opens the context menu.
While editing entries: Saves the edits.
W
TU
V
Note
You can also first lift the handset before opening the phonebook.

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
6en fr fa ar
1110-01
Dialling from the call list
The call list contains the numbers of the last 50 incoming calls.
Requirement: Telephone number display is possible for incoming calls
(£page 11).
Multiple calls from one number are only displayed once (with the infor-
mation of the last call). If the name is transmitted or the number is saved
to the phonebook, the accompanying name is also displayed.
YOpen the call list using the control key t.
qSelect the number or name.
either ...
cLift the handset.
... or
[Open the context menu.
qSelect CALL BACK and initiate the call using the speaker
with [. To make the call using the handset, simply lift the
handset.
Last number redial
The last five numbers dialled are automatically saved (each a max. of
32 digits).
Dialling the last saved number:
c I Lift the handset, press the redial key.
Dialling one of the last five numbers saved:
IPress the redial key.
qSelect the number.
cLift the handset.
or
vInitiate the call using the speaker with [.
Deleting all redial numbers
K I # 2 5 Press the key sequence.
KPress the set key or [to confirm.
Speed dialling
10 numbers can be saved for speed dial on the number keys 0 ... 9
(£page 8).
JPress the speed dial key.
Q... OPress the speed dial number key.
cLift the handset, the @key or initiate the call with [.
The number stored on the number key is dialled.
Dialling pauses
One or more dialling pauses can be entered using I(not at 1st digit).
Pauses are transferred to the memory and are necessary for certain
extension systems (e.g. 0 I2368).
The length of the pause can be set to 1, 3 or 6 seconds (£page 12).
Incoming calls
Incoming calls are indicated by the ring tone and in the display.
For number displays (£page 11), the number is visible in the display
and the fsymbol flashes. This symbol disappears when you answer the
call or (if you don't answer) by calling up the call list. The name is also dis-
played for callers who are stored in the phonebook with names.
If the VIP mode is activated (£page 9) the VIP symbol flashes in the dis-
play and the VIP ring tone signals the call.
Accepting a call
cLift the handset.
or
@Press the hands-free key to accept the call via the speaker.
Using open listening / hands-free
Switching open listening on/off
The persons present in the room can listen to the call over the speaker.
During the call using the handset:
@Press the hands-free key to switch open listening on or off.
When the speaker is switched on and the handset is picked up, open lis-
tening is switched on. In this case, the hands-free microphone is
switched off.
When the speaker is switched on and the handset is in the cradle, hands-
free via the hands-free microphone is switched on.
Switching from open listening to hands-free:
@ & Replace the handset while pressing the hands-free key.
Switching hands-free on/off
You can also make a call via the microphone with the handset in the cra-
dle. The optimum distance from the microphone is approx. 50 cm.
Switching on hands-free during a call
@ & Replace the handset while pressing the hands-free key.
Switching on hands-free prior to dialling
@Hands-free key, wait for dial tone.
Switching off hands-free
cLift the handset during the call. The call is transferred to
the handset.
Ending a call
@Press the hands-free key during a call via the speaker.
Note
You can also first lift the handset before opening the call list.
Note
You can also first lift the handset before pressing the speed dial key.

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
en fr fa ar 7
1110-01
Settings during a call
Setting the handset volume
There are three adjustable levels.
E/ DSet the volume using the volume up/volume down keys.
The set volume is shown in the display.
Setting the speaker volume
There are seven adjustable levels.
During hands-free speaking or open listening:
E/ DSet the volume using the volume up/volume down keys.
The set volume is shown in the display.
Mute
You can switch off the microphone or handset and microphone during a
call according to the setting of the mute function (£page 9):
CPress the mute key to switch the mute function on or off.
During muting of the microphone, a melody can be played.
Once the telephone has been muted this is indicated in the display with
the msymbol.
Changing the ringer and ringer volume
While the telephone is ringing, the volume and ringer can be changed.
Changing the volume
E/ DSet the ringer volume with the volume up/volume down
keys (5 levels, 0=silent).
Changing the melody
Q... OSelect the ringtone with the numeric keys (choice of 10).
Using the phonebook
Your Gigaset DA610 contains a phonebook in which you can save up to
50 entries, each with a maximum of 32 digits for numbers and 14 char-
acters for names.
You can make a call (£page 5), add new entries and manage and mod-
ify entries (£page 7) using the phonebook.
You can manually enter numbers and names or transfer them from the
call list (£page 8). You can also allocate VIP mode to a number.
The Zsymbol is indicated in the display if the phonebook has been
opened. The phonebook entry number is also visible (01... 50). If there is
at least one VIP entry in the phonebook, this is indicated in the display
via the lsymbol.
The phonebook provides the following functions in a menu:
Opening the phonebook
In standby:
ZPress the control key s.
Searching for an entry
qSelect an entry.
or
~Enter letters (£page 5). The name of the first entry start-
ing with this letter is displayed.
Showing the number of an entry
#Press the hash key to switch between number and name
display.
Saving numbers
ZOpen the phonebook.
The first entry in the list is displayed.
tSelect NEW ENTRY and confirm with [.
~Enter number and confirm with [.
~Enter name and confirm with [.
The entry is saved and shown in the display.
*Press the star key to turn the entry into a VIP entry. Press
again to delete the setting.
Editing an entry
ZOpen the phonebook.
The first entry in the list is displayed.
qSelect the entry and open the context menu with [.
qSelect EDIT ENTRY and confirm with [.
~Change the number and confirm with [.
~Change the name and confirm with [.
[Confirm the saving of the entry in the phonebook.
Deleting an entry / Deleting all entries
ZOpen the phonebook.
The first entry in the list is displayed.
qSelect an entry and open the context menu with [.
qSelect DELETE ENTRY to delete the selected entry or
DELETE ALL to delete all entries and confirm with [.
[Press the control key to confirm the action.
NEW ENTRY
Entry 1-50 DIAL ENTRY
. . . EDIT ENTRY
NEW ENTRY
DELETE ENTRY
DELETE ALL
Note
If you press *, the entry is set as a VIP entry or the setting is
deleted.

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
8en fr fa ar
1110-01
Using the call list (CLIP)
Incoming calls are saved if the number is transmitted (£page 11). Up to
50 calls are saved. If the number is the same, only the last incoming call
is saved. The oldest call is automatically deleted when there are more
than 50 calls. If transmitted, the caller’s name is also displayed. If the
caller is saved to the phonebook, the phonebook name is used. If there
are any missed calls in the list the f symbol flashes.
You can use the call list for the following functions:
¤Calling a number from the list (£page 6).
¤Saving a number in the phonebook.
The call list provides the following functions in a menu:
Opening the call list
You can open the call list in idle mode or when the handset is lifted.
YPress the control key t.
Viewing an entry
qSelect an entry.
If the number and name are available the name is shown first. To view
the number:
#Press the hash key. Use this key to switch between the
number and name display.
Transferring a number from the call list to the phonebook
YOpen the call list.
qSelect the entry and open the context menu with [.
qSelect SAVE NUMBER and confirm with [.
~Change the number (if required) and confirm with [.
~Enter or edit the name and confirm with [.
Deleting an entry / Deleting all entries
YOpen the call list.
qSelect an entry and open the context menu with [.
qSelect DELETE ENTRY to delete the selected entry or
DELETE ALL to delete all entries and confirm with [.
[Press the control key to confirm the action.
Using speed dialling numbers
You can save 10 numbers for speed dial on the number keys (each with
max. 32 digits).
Storing a speed dial number
You can enter the number in idle mode or when the handset is lifted.
K J Press the set key, press the speed dial key.
Q... OChoose a speed dial key and press [.
If the key is already allocated, the content is displayed.
either ...
~Enter the phone number for speed dial.
... or
Take over the phone number from the call or redial list
t/ IOpen the call/redial list.
qSelect the desired entry in the list and press [.
Storing the speed dial entry
KPress the set key or [.
Notes
When storing speed dial numbers, please note the following:
u*and #are saved regardless of the set dialling mode but are
only dialled with tone dialling mode (£page 11).
uIf the number entered is longer than 32 digits, only the first 32 digits
are stored.
A single speed dial number cannot be deleted but only overwritten.
Adjusting the telephone
To adjust the settings of your telephone you use the Kset key. You
can make settings in idle mode and when the handset is lifted.
Changing the language
You can change the language for display messages. There are six lan-
guages to choose from.
K Activate setting mode.
5 L Press the key code for setting the language.
Press the key for the desired language:
KSave your settings and exit the setting mode.
Entry 1-50 CALL BACK
SAVE NUMBER
DELETE ENTRY
DELETE ALL
QEnglish 3Spanish
German 4Italian
2French 5Dutch

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
en fr fa ar 9
1110-01
Setting the date and time
You can adjust the current date manually and change the format of the
display. The time is updated by incoming calls with telephone number
displays. You can adjust this setting if necessary (£page 12).
Setting the date and time
K 3 Activate setting mode for the date and time. The date and
time display becomes editable.
~Enter a 4-digit date and a 4-digit time. Use the qcontrol
key to move one position forwards/backwards.
KSave your settings and exit the setting mode.
The date setting format is according to the one currently set. The time
setting format is always 24-hour, regardless of the set time format.
Setting the date format
K Activate setting mode.
5 Press the key code for setting the date format.
Press the key code for the desired date format:
KSave your settings and exit the setting mode.
Setting the time format
K Activate setting mode.
5 Q Press the key code for setting the time format.
Press the key for the desired time format:
KSave your settings and exit the setting mode.
Setting the handset volume
The handset volume can be set using the setting mode or changed
directly during the telephone conversation using the keys (£page 7).
There are three adjustable levels.
K O Activate setting mode for the handset volume.
Press the key code for the desired volume:
KSave your settings and exit the setting mode.
Setting the mute behaviour and music on hold
You can define the behaviour of the microphone and the handset when
the telephone is muted and whether or not a melody is played.
K Activate setting mode.
O # Press the key code for mute setting.
Press the key code for the desired behaviour:
KSave your settings and exit the setting mode.
The mute function is activated according to these settings using the
mute key during a call (£page 7).
Setting the ringer
The following optional settings are available:
¤Melody and volume
¤VIP melody
¤Switching the ringer off
Setting the ring tone and volume
You can set the ring tone and volume or switch the ringer off. There are
10 different ring tones available and the volume can be adjusted to 5 lev-
els (0=silent).
You can also change both settings directly using the keys while the tele-
phone is ringing (£page 7).
Changing the ringer volume
K 5 Activate setting mode for the ringer volume. The currently
set ringer is played.
D / EIncrease or decrease the volume for the ringer.
or
Q... 4Select the desired value using the number keys.
KPress the set key or [to save your settings and exit the
setting mode.
Changing the ring tone
K M Activate setting mode for the ring tone. If you lift the hand-
set, you will hear the currently set ring tone.
Q... OSelect the required ring tone.
KPress the set key or [to save your settings and exit the
setting mode.
Setting the VIP ring tone and volume
You can set one of the ringers as a VIP ring tone. If you have assigned VIP
status to a number from the phonebook (£page 7), an incoming call
from this number will be indicated by the VIP ring tone.
Qfor MM/DD e.g. 12/31 for 31 December
for DD/MM e.g. 31/12
2for MM.DD e.g. 12.31
3for DD.MM e.g. 31.12
12-hour format
224-hour format
low 2medium 3high
QMicrophone and receiver off, melody on.
While in mute mode, the person on the other end of
the line hears a melody.
Microphone, receiver and melody off.
The telephone is completely muted.
2Microphone off, receiver on, melody off.
You are still able to hear the person on the end of
the line, however they cannot hear you.
Note
The ring tones are played over the speaker if you lift the handset
before commencing with the settings.
Note
The ring tone can only sound perfectly when the ring pulse arriving
from the telephone network is long enough. The length of the pulses
may differ from network to network. It is therefore possible that some
ring tones for selection may sound clipped. If this is the case please
select another ring tone.

Gi
gaset
DA
610
/
en
/
A
30350-
M
212-
A
601-1-
UZ
19
/
te
l
ep
h
ony.
f
m
/
23.04.2012
10 en fr fa ar
1110-01
Changing the VIP ringer volume
K 5 *
Activate setting mode for the VIP ringer volume. If you lift
the handset, you will hear the VIP ringer at the currently
set volume.
D / EIncrease or decrease the volume for the ringer.
or
Q... 4Select the desired value using the number keys.
KPress the set key or [to save your settings and exit the
setting mode.
Changing the VIP ring tone
K M *
Activate setting mode for the VIP ring tone. If you lift the
handset, you will hear the currently set VIP ring tone.
Q... OSelect the required ring tone.
KPress the set key or [to save your settings and exit the
setting mode.
Switching the ringer off
If you do not wish to be disturbed, you can switch off the ringer. The fol-
lowing three settings are available: all tones off, VIP only on, all tones on.
*Hold down the key to switch all ring tones off.
or
K * K
Press the key sequence to switch the ringer off for normal
callers but leave it on for VIP contacts.
Pressing the key sequence again will switch off the ringer
for all callers.
Once the ring tone has been switched off, the xsymbol appears in the
display.
Switching the ringer back on
*Hold down the key to switch all ring tones on.
Security settings
Locking the telephone
You can secure your telephone against unauthorised access by using the
key lock. When the key lock is activated, all keys are locked, with the
exception of the #key and the stored emergency number (see
below).
Activating the key lock
#When the telephone is on standby, press and hold down
the lock key.
Once the key lock has been switched on, the isymbol and the KEYS
LOCKED message appear in the display. If the handset is lifted, the key
lock is indicated by .
Deactivating the key lock
#Hold down the lock key.
Emergency calls
There are two emergency numbers stored in the telephone by default
(110, 112). You can store an additional emergency number with up to 32
digits. These emergency numbers can also be selected when the key
lock is switched on.
Selecting an emergency number with activated key lock
c Lift the handset. is displayed.
~Enter the emergency number.
Saving the emergency number
K N 3
Activate setting mode for the emergency number. If an
emergency number is already set, it is displayed. Hold
down the ukey to clear the number.
Q... O/ */ #/ H/ I
Enter the emergency number.
KPress the set key or [to save your settings and exit the
setting mode.
Direct calling (baby call)
When direct calling is activated, the stored number (max. 32 digits) is
dialled by pressing any key (except for the key sequence
K N 2).
Activating direct calling
K N 2
Activate setting mode for direct calling.
Q... O/ */ #/ H/ I
Enter the direct calling number.
KPress the set key or [to activate direct calling and exit
the setting mode.
Deactivating direct calling
K N 2
Activate setting mode for direct calling.
XHold down the ukey to clear the direct call number.
KPress the set key or [to deactivate direct calling and exit
the setting mode.
Blocking numbers
You can block phone calls to specific dialling codes (e.g. chargeable
codes), max. 3 numbers with 5 digits each.
K 2 Activate setting mode for blocking numbers. If a dialling
code is already set, it is displayed. Hold down the ukey
to clear the entry.
Q... OEnter the dialling code to be blocked (max. 5 digits).
To edit the next dialling code:
vConfirm with [and continue.
To save the settings:
KSave your settings and exit the setting mode.
Note: The names of persons, whose numbers are stored in the phone-
book with the area code defined here, are no longer displayed. Change
the appropriate phonebook entries, where necessary.