Side Plate
M8*20(mm) Screws
PM4*12(mm) Screws 5/16’’*1.02(inch)
UNC Screws
(Figure 4)
(Figure 5)
Yoke Mount (Figure 5)
Wiring Diagram
1. Route the cord into the mounting bracket through the wiring hole,
slide the fixture onto the bracket and tighten the two 5/16" screws.
3. Use the hole pattern on the yoke mount to locate the places to drill the
holes in the installation surface, then attach the mount to the surface
using using 3/8"*1-1/2" hex screws (not included).
3. Loosen the center bolts and set screws, rotate the fixture to the desired
angle, then tighten the center bolts.
4. Make wiring connections per the wiring diagram below.
5. After setting the mount to the desired angle, the center bolts and set
screws should be locked using a manual wrench.
(Figure 3)
Wall Mount (Figure 3)
1. Loosen the four PM4*8(mm) screws and remove the side plate from the
mounting bracket.
2. Attach the back plate to the arm bracket using the KM4*10(mm) screws.
3. Use the provided plastic template to locate the places to drill the holes
in the wall, then attach the bracket to the wall using four 3/8" screws
(not included).
4. Route the power cord into the mounting bracket, slide the fixture onto
the bracket, then tighten the two bottom 5/16" screws.
5. Make wiring connections as per the wiring diagram on the next page,
replace the side plate, and fasten the PM4*8(mm) screws.
5/16"*1.02(inch)
UNC Screws
PM4*8(mm) Screws
Side Plate
PM4*12(mm)
Screws OPEN
Back Plate
KM4*10(mm)
Screws
1/2"*1.46(inch)
UNC Screws
Slipfitter (Figure 4)
1. Loosen the two PM4*12(mm) screws and remove the side plate from the
mounting bracket.
2. Route the cord into the mounting bracket through the wiring hole,
slide the fixture onto the bracket and tighten the two bottom 5/16"
screws.
3. Loosen the HM10*25mm hex bolt to adjust the bracket to the desired
angle. Once the fixture is at the desired angle, retighten the HM10*25mm
hex bolt.
4. Make wiring connections per the wiring diagram below.
5. Slip lower fitter over 2 - 3/8" (60 mm) o.d. heavy wall pipe or tenon and
tighten the four M8*20mm hexagon head set screws, making sure not to
pinch any leads.
3.74in. (95mm.)
2in. (51mm.)
ø0.87in.
(ø22mm.)
ø0.43in.
(ø11mm.)
ø0.55in.
(ø14mm.)
5/16’’*1.02(inch)
UNC Screws
Set Screws
Center Bolts
PHOTOCONTROL
MOTION SENSOR
LAMPLOAD
INPUT
WHITE
BLACK RED
Note: Two dimming wires in the the
driver box.
Note: A black/white 12V+ wire may be present and unconnected in some fixtures.
Black
White
Green/Yellow Green
Neutral
Purple
Pink
Ground
Line
5/16"*1.02(inch)
UNC Screws
Adjustable Pole Mount (Figure 2)
1. Loosen the six PM4*12 screws and remove the two side plates.
2. Attach the bracket to the pole using the provided two 3/8" screws.
3. Loosen the M10 screw and adjust the fixture to the desired angle.
3. Route the cord into the mounting bracket through the wiring hole,
slide the fixture onto the bracket and tighten the two bottom 5/16"
screws.
4. Make wiring connections as per the wiring diagram on the next
page, replace the two side plates, and fasten the PM4*12(mm)
screws. When replacing the side plates, make sure that the power
cord is not exposed and does not press against the wiring.
3/8"*1.575(inch)
UNC Screws
HWM4*6(mm)
Screws
PM4*12(mm)
Screws
PM4*12(mm)
Screws
Gasket B
Gasket A Side Plate
M10 Screw
Side Plate
OPEN
(Figure 2)
2
