Glacier bay HDGMBS4 User manual

THANK YOU
THANK YOUTHANK YOU
THANK YOU
We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this drinking ater
filtration system. We strive to continually create quality products designed to enhance your home. Visit us online to
see our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
Item # 1001 104 020
Model # HDGMBS4
USE AND CARE GUIDE
ULTIMATE DEFENSE DRINKING WATER FILTRATION
S STEM
Questions, problems, missing parts? Before returning to the store,
call Glacier Bay Customer Service
7 a.m. - 6 p.m., CS , Monday - Friday
1
11
1-
--
-800
800800
800-
--
-247
247247
247-
--
-1087
10871087
1087
HOMEDEPO .COM
HOMEDEPO .COMHOMEDEPO .COM
HOMEDEPO .COM/GLACIER
/GLACIER/GLACIER
/GLACIERBAY
BAYBAY
BAY
201-8401420 (rev 00)
System tested and certified by NSF International
against NSF/ANSI Standards 42 & 53.
See performance data sheet for details.
NSF ®
System tested and certified by WQA against
NSF/ANSI Standards 42, 53 and USEPA
microbiological guide for the reduction of the
claims specified on the performance data sheet.
C
USA

2
Table of Contents
Safety Information .................................2
Warranty .................................................2
Pre-Installation ......................................3
Installation .............................................6
Filter Cartridges .................................... 8
Faucet Timer and Battery ..................... 9
Troubleshooting .................................. 10
Service Parts ....................................... 10
Safety Information
Read all instructions before installing and using your
home water filtration system. Follow all steps
exactly to correctly install. Reading this manual will
also help you to get all the benefits from the
filtration system.
All plumbing must be completed in accordance with
national, state and local plumbing codes. Local code
information can be obtained at your local public
works department. In Massachusetts, plumbing
code 248 CMR 3.00 and 10.00 shall be adhered to.
Consult with your licensed plumber.
WARNING:
: :
: Do not use with water that is
microbiologically unsafe or of unknown quality
without adequate disinfection before or after the
system.
WARNING:
: :
: Do not use for the treatment of water
that is visually contaminated (cloudy) or has an
obvious contamination source, such as
contamination by raw sewage.
CAUTION:
: :
: Do not install the filtration system
outside, or in extreme hot or cold temperatures.
emperature of the water supply to the filtration
system must be between 40°F and 100°F. Do not
install on a hot water line.
NOTICE:
: :
: his filtration system works on water pressures of 40
psi (minimum) to 100 psi (maximum). If your house water
pressure is over the maximum, install a pressure reducing valve
in the water supply pipe to the filtration system.
NOTICE:
: :
: Commonwealth of Massachusetts plumbing codes
do not permit the use of saddle valves and require installation by
a licensed plumber. Comply with plumbing code 248-CMR for
installations in the state of Massachusetts. Please consult your
local plumber.
Warranty
GLACIER BAY WA ER FI
GLACIER BAY WA ER FIGLACIER BAY WA ER FI
GLACIER BAY WA ER FIL RA ION SYS EMS
L RA ION SYS EMS L RA ION SYS EMS
L RA ION SYS EMS -
--
- WARRAN Y
WARRAN YWARRAN Y
WARRAN Y
Glacier Bay Water Filtration Systems are manufactured under the highest standards of quality and workmanship.
Glacier Bay Water Filtration Systems warrants to the original purchaser that this system will be leak and drip free
during normal domestic use for a period of one (1) year from date of purchase. If this system should ever develop a
leak or drip Glacier Bay Water Filtration Systems will free of charge provide the parts necessary to put the system
back in good working condition. A replacement for any defective part will be supplied free of charge for installation
by the purchaser. Defects or damage caused by use of other than authorized parts are not covered by this warranty.
his warranty shall be effective from date of purchase as shown on purchaser’s receipt. Glacier Bay Water Filtration
Systems shall be installed per the manufacturer’s installation instructions and specifications. Some states do not
allow limitations on how long a warranty lasts, so the above limitation may not apply to you. his warranty is valid
for the original purchaser only and excludes industrial, commercial, or business use of the product, product misuse,
and product damage due to installation error, whether performed by a contractor, service company, or yourself.
Glacier Bay Water Filtration Systems will not be responsible for labor charges or for damage incurred during
installation, repair or replacement, nor for incidental or consequential damages. Some states, provinces and nations
do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusions or
limitations may not apply to you. Glacier Bay Water Filtration Systems will advise you of the procedure to follow in
making warranty claims.
Simply write to Glacier Bay Water Filtration Systems at the address below. Explain the defect and include proof of
purchase and you name, address and telephone number or you can also call us at 1-800-247-1087.
U.S.A Canada
Glacier Bay Water Filtration Systems Glacier Bay Water Filtration Systems
2455 Paces Ferry Road, N.W. 900-1 Concorde Gate
Atlanta, GA 30339-4024 oronto, ON M3C 4H9

3 HOMEDEPO .COM/GLACIERBAY
Please contact 1-800-247-1087 for further assistance.
Pre-Installation
ABOU HIS FIL RA IO
ABOU HIS FIL RA IOABOU HIS FIL RA IO
ABOU HIS FIL RA ION SYS EM
N SYS EMN SYS EM
N SYS EM
he Ultimate Defense Drinking Water Filtration System uses a dual filter configuration to remove undesirable
elements in your water. hese elements may include chlorine taste and odor, particulates, lead, virus, bacteria,
cysts, and many organic compounds. At the same time, the system allows the minerals found in water to remain, for
great tasting water. he filters in this system are designed to stop the flow of water when their capability to protect
the user has been exhausted.
A performance data sheet is included listing what the system will reduce from the water supply. See the
performance data sheet for individual contaminants and microbial reduction performance.
INS ALLA ION LOCA IO
INS ALLA ION LOCA IOINS ALLA ION LOCA IO
INS ALLA ION LOCA ION
NN
N
he drinking water system fits under the kitchen or bathroom sink. However, you can install it where it is most
convenient. You need a COLD water supply pipe within a few feet (6 feet of tubing is included). You can purchase
longer lengths of tubing if needed to reach more distant points. Be sure tubing is acceptable for use on potable
water supplies.
DIMENSIONS
DIMENSIONSDIMENSIONS
DIMENSIONS
SPECIFICA IONS
SPECIFICA IONSSPECIFICA IONS
SPECIFICA IONS
Minimum
Minimum Minimum
Minimum –
––
– Maximum Supply Water Pressure
Maximum Supply Water PressureMaximum Supply Water Pressure
Maximum Supply Water Pressure 40 – 100 PSI (276 – 689 kPa)
Minimum
Minimum Minimum
Minimum –
––
– Maximum Supply Water emperature
Maximum Supply Water emperatureMaximum Supply Water emperature
Maximum Supply Water emperature 40 - 100°F (5 - 38°C)
Inlet
Inlet Inlet
Inlet –
––
– Outlet
OutletOutlet
Outlet 3/8 in. quick connect fittings and tubing included
Maximum Supply Water Iron, Manganese, and Hydrogen
Maximum Supply Water Iron, Manganese, and Hydrogen Maximum Supply Water Iron, Manganese, and Hydrogen
Maximum Supply Water Iron, Manganese, and Hydrogen
Sulfide
SulfideSulfide
Sulfide
0
SINK
Yellow tube
WA ER IN
Blue tube
WA ER OU
Filte
r
ed
water faucet
HO COLD
Shutoff
valve
Supply
fitting
4 7/8 in.
12 in.
15 1/4 in.
17 5/8 in.

4

5 HOMEDEPO .COM/GLACIERBAY
Please contact 1-800-247-1087 for further assistance.
Pre-Installation (continued)
OOLS REQUIRED
OOLS REQUIREDOOLS REQUIRED
OOLS REQUIRED
Phillips
screwdriver
Pliers
Adjustable
wrench
ubing
cutter
Drill and 1-1/4
in. drill bit
Sealant tape
PACKAGE
PACKAGE PACKAGE
PACKAGE CON EN S
CON EN SCON EN S
CON EN S
Part
PartPart
Part Description
DescriptionDescription
Description Quantity
QuantityQuantity
Quantity
A Filtration system 1
B Feed adapter (water supply fitting) 1
C Filtered water faucet for sink/countertop mounting 1
D 3/8 in. color-coded tubing (used for all connections) 2
E Filter cartridge 2
A
B
C
D
E

6
Installation
1
Connectin
ConnectinConnectin
Connecting the feed water
g the feed water g the feed water
g the feed water
supply fitting
supply fittingsupply fitting
supply fitting
NOTICE:
: :
: Commonwealth of Massachusetts plumbing codes
do not permit the use of saddle valves and
require installation by a licensed plumber. Comply with
plumbing code 248-CMR for installations in the
state of Massachusetts. Please consult your local plumber.
Check and comply with local plumbing codes as you
plan and install a cold feed (supply) water fitting. he
fitting must provide a leak-tight connection to the
water filter 3/8 in. tubing (D). A typical connection
using the water supply fitting (B) is shown in Figure
A.
An optional connection using standard plumbing
fittings (not included) is shown in Figure B.
Installation using the Fitting (Figure A):
□Close the cold water shut off valve that is
immediately upstream of where you will install
the feed water supply fitting. Open the faucet to
drain water from the sink cold water pipe.
□Remove the nut that connects the cold water
faucet to cold water plumbing.
□hread the water supply fitting (B) onto the pipe
and reconnect the nut to the bottom of the fitting.
Installation using Optional Pipe Fittings (compression
type shown – Figure B):
□Close the cold water shut off valve that is
immediately upstream of where you will install
the feed water supply fitting. Open the faucet to
drain water from the sink cold water pipe.
□Install a fitting on the cold water pipe to adapt to
the 3/8 in. OD tubing.
□If threaded fittings are used, be sure to use pipe
joint compound or thread sealing tape on outside
threads.
Figure B
Figure A
B
D
Cold water
pipe
hread sealing
tape on threads
Cold water
faucet stud
Cold water
shutoff
Cold water
shutoff
Ferrule
Cold water
pipe
3/8 in.
Compression
fitting Insert
3/8 in. tubing
to W
ater Filter
inlet

7 HOMEDEPO .COM/GLACIERBAY
Please contact 1-800-247-1087 for further assistance.
Installation (continued)
2
Installing the faucet
Installing the faucetInstalling the faucet
Installing the faucet
IMPORTANT:
: :
: o avoid damaging the sink, consult a
qualified plumber or installer for drilling procedures in
porcelain or stainless steel. Special drill bits are made for
this.
Before you begin, ensure there is room underneath
the sink or countertop so you can make the needed
connections. If drilling is required in the sink top or
countertop next to the sink, make a 1-1/4 in. dia.
(minimum) hole for the faucet (C).
□Insert one end of the blue tube into the faucet (C)
(see Step 3 – Connecting the tubes). Feed the
other end of the blue tube through the mounting
hole.
□Slide the toggle bolts through the mounting hole
until the faucet (C) base is square against the
mounting surface (sink or countertop)
. ighten the
toggle bolts to secure the base flat on the
mounting surface. Do not over-tighten.
□urn the faucet (C) 1/4 clockwise to attach the
faucet (C) to the base.
3
Connecting the tubes
Connecting the tubesConnecting the tubes
Connecting the tubes
Remove and discard the protective foam plugs (if
present) before connecting tubes.
□
Allowing some slack, measure and cut a length of
3/8 in. tubing (D) to connect between the supply
fitting and the filter system inlet. Cut the ends of
the tubing square.
□Insert tubing all the way into the supply fitting
and inlet fitting. Pull on the tubing to be sure that
it is securely set in the fittings.
□Repeat the first two bullets to connect the tubing
from the faucet to the filter system outlet.
ubing Connecti
ubing Connectiubing Connecti
ubing Connection (all push
on (all pushon (all push
on (all push-
--
-in fitting
in fittingin fitting
in fittings):
s):s):
s):
his system includes push-in fittings for quick tubing
connections. If working with the fittings, do the
following:
□Cut the end of the tubing square. Inspect the end
(about 1 in.) of the tubing to be sure there are no
nicks, scratches or other rough spots. If needed,
cut the tubing again.
□Push tubing through the collet and through the
fitting. Full engagement is 3/4 in. length of tube
into the fitting. If tubing other than supplied with
the system is used, be sure it is of high quality,
exact size and roundness with a smooth surface.
C
1/4 turn to connect
faucet to base
Toggle bolt
Screw
Faucet base
Rubber washer
Hole in sink
or counter
End of tubing round and smooth,
with no cuts, nicks or flat spots
Correct full 3/4 in.
engagement
Tubing correctly cut and connected
Incorrect partial
engagement
To disconnect, push the collet inward and
hold with a finger while pushing the tubing out:
Remove and discard foam plugs
Foam plug
Push
in
fitting

8
Installation (continued)
4
Installing the filter cartridges
Installing the filter cartridgesInstalling the filter cartridges
Installing the filter cartridges
5
Completing the installation
Completing the installationCompleting the installation
Completing the installation
□Remove the plastic cap from the filter cartridges (E).
□Install the filter cartridges (E) into the two holes in
the filter body. Note the filter cartridges are labeled
Filter 1 and Filter 2. urn clockwise to tighten. Do
not over tighten.
□Open the shutoff valve that you closed at the
beginning of this installation.
□Open the filtered water faucet (C) to purge air
from the system. When the water runs smooth
with no bubbles or spurting close the faucet
(C) and check the installation for leaks.
□Open the filtered water faucet (C) and let
water run for 10 minutes to rinse system.
Filter Cartridges
FIL ER CAR RIDGE LIF
FIL ER CAR RIDGE LIFFIL ER CAR RIDGE LIF
FIL ER CAR RIDGE LIFE
EE
E
Lead, Chlorine Taste and Odor, and Purifying Filter Cartridges: Lead, chlorine taste and odor, and purifying filter
cartridges contain activated carbon. When new, open the filtered water faucet and allow fine, carbon particles to
purge from the cartridges. Flush for 10 minutes. It is recommended to replace filter cartridges every six months or
350 gallons of use. here are several variables that determine how long a cartridge will last. hese include:
1. How much water you use, and
2. How much sediment, taste and/or odor, or other unwanted substance, is in the water.
Use the following information as a guide. However, no matter which type of filter cartridge you are using, you will
know it is time to replace it when you first notice the return of the unwanted substance in your water.
Glacier Bay Ultimate Defense Water Filtration System model HDGMBS4 with replacement elements HDGMBF4
conforms to NSF/ANSI 42 and 53 for the specific performance claims as verified and substantiated by test data. he
rated capacity for this system is 350 gallons (1325 liters) at a rated service flow of 0.74 gallons per minute.
State of Wisconsin Required Statement: Do not use in Wisconsin with water that is microbiologically unsafe, or of
unknown quality, without adequate point of entry (i.e. whole house) disinfection before this device.
FIL ER CAR RIDGE REP
FIL ER CAR RIDGE REPFIL ER CAR RIDGE REP
FIL ER CAR RIDGE REPLACEMEN
LACEMENLACEMEN
LACEMEN
1. urn the filter cartridges counterclockwise to remove and dispose of them properly.
2. Install the new filter cartridges by turning them clockwise.
3. Remove and replace the timer battery. See the Changing the Faucet Battery section for more information.
Lead, Chlorine Taste and Odor, and Purifying Filter Cartridges: Lead, chlorine taste and odor, and purifying filter
cartridges contain activated carbon. When new, open the filtered water faucet and allow fine, carbon particles to
purge from the cartridges. Flush for 10 minutes.
E A
Turn filter cartridge
counterclockwise to remove
Turn filter cartridge
clockwise to install

9 HOMEDEPO .COM/GLACIERBAY
Please contact 1-800-247-1087 for further assistance.
Faucet Timer and Battery
FAUCE IMER
FAUCE IMERFAUCE IMER
FAUCE IMER
Inside the faucet base is a battery-operated 6 month timer.
An amber LED indicator is also located in the front of the faucet base. his LED flashes continuously after 6 months
have passed. his indicates that it is time to replace the battery and filters.
CHANGING HE FAUCE
CHANGING HE FAUCE CHANGING HE FAUCE
CHANGING HE FAUCE BA ERY
BA ERYBA ERY
BA ERY
o change the battery, complete the following steps:
1. Loosen the screw on the right side of the faucet base.
2. Press the battery housing upwards from the faucet base until it releases from the base.
3. Replace the battery (CR 2032 or equivalent). Place battery into the holder with the positive (+) side
facing the back of the holder.
4. When the battery is first replaced, the light in the base will flash six times and turn off. his indicates
the battery is fully charged. After the six flashes, the timer enters the 6 month time cycle. If it
repeatedly flashes two times, the battery is weak and needs to be replaced.
5. Re-install the battery housing and firmly tighten the mounting screw.
Battery housing
Screw
Battery
negative (-) side
facing the front

10
Troubleshooting
Problem
ProblemProblem
Problem Probable Cause
Probable CauseProbable Cause
Probable Cause Solution
SolutionSolution
Solution
here is either no or a decreased
water flow.
he prefilter is clogged. Replace the prefilter cartridge.
Flow through the purifying filter will
decrease and eventually clog when
exposed to an excess of
microbiological loading materials in
the water. his failsafe feature
reduces the chance of product use
beyond its intended life, and will
shut down the filter when it is
exposed to contaminated water.
Replace all filter cartridges.
he water tastes bad and has an
odor.
he filters are expended. Replace the filter cartridges.
he system is contaminated. Sanitize the system. Call 1-800-247-
1087 for instructions.
Faucet LED indicator light does not
function after a battery change.
he battery is dead. Replace the battery.
he battery is not installed correctly. Install the battery correctly, paying
attention to the polarity.
Water leaks at the push connect
fittings.
he tubing is not pushed in all the
way.
Push tubing in all the way into
fittings.
he tubing is not cut square. Cut the tubing square.
he tubing is nicked. Remove the nicked portion and
reinsert the tubing into the fitting.
he outer tubing surface is not
smooth.
Remove the rough portion, and
reinsert the tubing into the fitting.
Service Parts
Key
Key Key
Key
Number
NumberNumber
Number
Part Number
Part NumberPart Number
Part Number Description
DescriptionDescription
Description Key
Key Key
Key
Number
NumberNumber
Number
Part Number
Part NumberPart Number
Part Number Description
DescriptionDescription
Description
1 119-8600048 Faucet with base and
electronics
5 3/8 x 3/8 in. coupler
2 1073-24-01 Cabinet, left 6 1073-24-02 Cabinet, right
3 1073-23-HC Head assembly
(includes #5)
7 HDGMBF4/HCGMBF5 Replacement filter
cartridge, 2-pack*
4 1073-23-05 Elbow fitting 8 7228536 ee, feed adapter
** 7157280 ubing, 3/8 in. x 20
ft., white
9 1073-22-09 3/8 x 3/8 in. union,
yellow
*Please purchase replacement cartridges from the retailer where you purchased this system.
** his tubing is not included. ubing lengths for remote installation, direct replacement for colored lengths of tubing.