Glasdon ECO NEXUS Quick start guide

ECO NEXUS CUP RECYCLING STATION
1.
To access the internal
compartments, lift the Lid
(ITEM 1) off the Bin Body
(ITEM 2).
PLACING SACK INTO POSITION
To install sacks, rstly insert into
the Sack Retention Slots (ITEM 3)
then stretch over the outer rim
Lower Lid to replace, ensuring
sacks are neatly secured
underneath.
2. 3.
Ensure that all personnel read the points listed within this leaet and that a copy is given to staff involved with
the installation and maintenance of this product. Glasdon recommends that a full Health and Safety analysis
is carried out prior to use.
COMPONENTS:
ITEM 1 - Lid
1 of 4
4
1
6
2
ITEM 3 - Sack Retention Slots
ITEM 4 - Internal Cradle
ITEM 5 - Cup Stacking Tubes
3
ITEM 2 - Bin Body
5
ITEM 6 - Liquid Reservoir
ECO NEXUS CUP RECYCLING STATION
OPERATIONAL INSTRUCTIONS
TM

Remove the Internal Cradle by
pulling it out of the Sack
Retention Slots in the Bin Body.
Remove the Liquid Reservoir
(ITEM 6) by lifting upwards,
pulling them out of the Internal
Cradle.
Release each sack individually
from the bin rim and lift
upwards out of the Bin Body.
Return the Cradle to the centre.
Remove the Cup Stacking
Tubes (ITEM 5) by lifting
upwards, pulling them out of
the Internal Cradle.
Rotate the Cup Stacking Tubes
180 degrees to allow the stacks
of cups to be removed.
Open the lid, move the Cradle
(ITEM 4) across to one side
2 of 4
EMPTYING THE ECO NEXUS CUP RECYCLING STATION
4. 5. 6.
7. 8. 9.
With bin body upside down,
click screw and wheel into
moulded slot. Repeat with
second wheel.
Push both socket caps
into the moulded recesses
opposite wheels.
From kit provided, place 1 screw
through a wheel.
ATTACHING THE WHEELS
10. 11. 12.

3 of 4
From the inside of the Bin Body
thread the Socket Screw
(ITEM 1) through the Bin.
Lay the Bin Body on its side on
a soft oor surface. From the
outside of the Bin Body place
the Extruded Spacer (ITEM 2)
onto the Socket Screw
Empty the internal components
from the inside of the Bin
Body. See steps 4-9 to assist in
emptying the bin.
13. 14. 15.
ECO NEXUS CUP RECYCLING STATION
SIGN KIT INSTALLATION INSTRUCTIONS
TM
ECO NEXUS CUP RECYCLING STATION SIGN KIT
Ensure that all personnel read the points listed within this leaet and that a copy is given to staff involved with
the installation and maintenance of this product. Glasdon recommends that a full Health and Safety analysis
is carried out prior to installation.
COMPONENTS:
ITEM 1 - Socket Screw x 1
5
ITEM 3 - Foamex Sign x 1
ITEM 4 - Nyloc Nut M6 x 1
ITEM 5 - Washer M6 x 2
8
ITEM 2 - Extruded Spacer x 1 4
ITEM 6 - Screw M6 x 2 3
7
2
1
ITEM 7 - Spacer x 2
TOOLS REQUIRED:
4mm Allen Key
6
ITEM 8 - Lug Nut x 2
INSTALLING THE SIGN KIT

.
Issue 2 - December 2017 - Stock No. C000/0511 - DWG No. 07B338-64
NEXUS IS A TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON GROUP OR ITS
SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
A planned maintenance schedule or regular inspection is
recommended, replacing components as necessary.
Replacement components are available direct from GLASDON.
GLASDON cannot be held responsible for claims arising from incorrect
installation, unauthorised modications or misuse of the product.
© Copyright DECEMBER 2017
Glasdon UK Ltd reserve the right to alter specications without prior notice.
Glasdon U.K. Limited
Preston New Road
BLACKPOOL
Lancashire FY4 4UL
Tel. : [phone]
Fax : [phone]
e-mail: [email protected]
web: www.glasdon.com
4 of 4
Repeat steps 18-19 for both
xing points. securely tighten the
xings with the Allen Key.
Thread the Nyloc Nut M6
(ITEM 4) onto the Socket Screw,
lightly tighten by hand.
Assemble the xings as shown
placing the Washer M6 (ITEM 5)
onto the Screw M6 (ITEM 6)
Place the spacer (ITEM 7)
between the Lug Nut
(ITEM 8) and the Foamex Sign.
Thread the assembled xings
through the Foamex Sign and
lightly tighten by hand.
Place the Foamex Sign (ITEM 3)
onto the Socket Screw ensuring
the graphic side is face down.
INSTALLING THE SIGN KIT
16. 17. 18.
19. 20.