Glatz Palazzo M8 User manual

Sunshade
Palazzo M8
Service Manual
Palazzo M8

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
The following tasks are described in this service manual:
1. Replace top .........................................................................................................3
2. Change cover ......................................................................................................3
3. Change bar..........................................................................................................5
4. Change cable wire and gear................................................................................6
5. Remove bracing ring for change of cable wire or gear ........................................6
6. Remove torsional bearing for change of cable wire or gear ................................7
7. Disassemble roller block for change of cable wire or gear ..................................8
8. Replace telescopic tube, cable wire or gear........................................................9
9. Replace spindle...................................................................................................9
10. Replace cable wire or gear ............................................................................10
11. Change of gear ..............................................................................................10
12. Assembling after change of gear (disassemble the sunshade according to items 1-11) ...........11
13. Change slide..................................................................................................12
14. Sunshade type marking S8............................................................................12
15. Serial numbers Palazzo M8 ......................................................................13-14
16. Exchange of the lighting.................................................................................15
17. Finished frame ..............................................................................................16
Subject to technical changes.
© Glatz AG 09/2010
GLATZ AG . Neuhofstrasse 12 . 8500 Frauenfeld . Switzerland . www.glatz.ch

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 3
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
Preparation: Provide clean pad to put down the sunshade
Tools: Hex key with wrench size 4.5 and 6 mm (or cordless drill),
open-end wrench with wrench size 10 mm and
19 mm. Cross-head screwdriver.
1. Replace top
Proceed as follows when the sunshade is in vertical or horizontal position:
•Screw of the lifting eye bolt at the top, screw in the new top
2. Change cover
•Loosen the screw at the rod extensions. Push the extension into the bar,
then pull out the fabric pocket and afterwards pull the extension out of the
bar. Loosen cable straps at the cornerbars.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 4
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
•Loosen the Velcro fastening
•Screw off the top. Unhook the hooks of the cover at the bars. Pull out the
fabric over the crown.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 5
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
3. Change bar
•First of all remove the pan head screws at the slide.
•Afterwards screw off the pan head screws at the crown and remove the
serrated lock washers as well as the bars.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 6
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
4. Change cable wire and gear
•First of all remove the fabric, then disassemble all bars
(see items 1 to 3)
•Remove nut from the cable wire at the slide and pull out the cable wire.
5. Remove bracing ring for change of cable wire or gear
•Remove 4 screws at the bracing ring, remove the bracing ring.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 7
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
6. Remove torsional bearing for change of cable wire or gear
•Loosen hex-head screws with an open-end wrench and remove them and
pull out the torsional bearing.
Torsional bearing; 2 hex-head screws

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 8
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
7. Disassemble roller block for change of cable wire or gear
•Remove screws of the roller block holder and pull out the cable wire
•Remove the two hex-head
screws on both sides (with and
without hole)
Slide stopper
roller block holder; exchange it and introduce the cable into it

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 9
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
8. Replace telescopic tube, cable wire or gear
•Disassemble the sunshade according to the procedure in items 1 to 7
•Pull out the telescopic tube
9. Replace spindle
•Disassemble the sunshade according to the procedure in items 1 to 8
•Loosen both hexagon socket screws and pull out the spindle

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 10
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
10. Replace cable wire or gear
•Disassemble the sunshade according to the procedure in items 1 to 9.
•Single parts of the spindle fixing
•cable length has to be adjusted at the slide
11. Change of gear
old version:
•Disassemble the sunshade according to the procedure in items 1 to 9
•Loosen 2 screws, remove the gear and put on the new gear.
New version (gear and spindle have a round diameter):
With an old spindle and new gear a connecting piece is needed.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 11
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
12. Assembling after change of gear
(disassemble the sunshade according to items 1-11)
•Insert the telescope and the gear into the mast and screw with the two
hex-head screws M16 and the two cross-head screws.
•Screw in the hexagon nut M 16 mm on both sides (with a hole and without
a hole).
●pull out the cable at the pulley
●attach the torsional bearing
●attach the roller block
●attach the cable at the slice and adjust the length
●set up the pole
●attach the struts
●install the textil cover
●attach the top

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 12
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
13. Change slide
•Remove the fabric according to items 1-2 and disassemble the rods
according to item 3.
•Remove the hex-head screws M16 (with and without hole) and the cable
wire fastening according to item 7 and pull the slide down out of the mast.
14. Sunshade type marking S8
•If it is a Palazzo S8, the name of the type is affixed to the slide. Another
feature is the rivetted hinge supports.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 13
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
15. Serial numbers Palazzo M8
•In case of Palazzo M8 of the first series the serial number is affixed to the
bottom of the mast.
•In case of the latest version the serial number is at the slide.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 14
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
•Another feature of the Palazzo M8 are the hinge supporters which are
rivetted and fixed at the bars and which are screwed together with the
slide by pan head screws and serrated lock washers.

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 15
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
16. Replacement of the lighting, lamp glass, shining tool
Replace the lighting. First of all unscrew the 4 screws on the bracing ring
(according to item 5). Then solve the lamp cable at the distribution box. To
remove the lamp glass unscrew the 8 screws at the lighting. Install the new
glass in reverse order.
glass parts (two pieces)

Sunshade
Palazzo M8
G latz AG 2011_Servicemanual Palazzo M8_en 16
Pfad:K:\Marketing&Verkauf\Drucksachen\Service Manual\Palazzo M8\Word Dateien\2011_Servicemanual Palazzo M8_en.doc
Created: Dino Aeschbacher/29.09.2010 Checked: Werner Maag/28.09.2010 Released: Sergio Malacarne/29.09.2010
17. Finished frame