Global American Inc. 3007680 User manual

User’s Manual
Version 1.0
PC/104 CPU Module 3007680

Table of Contents
Chapter 1 - Introduction
1.1 Copyright Notice.............................................................1
1.2 About User’s Manual .....................................................2
1.3 Warning.............................................................................2
1.4 Replacing the lithium battery ......................................3
1.5 Technical Support ..........................................................3
1.6 Warranty............................................................................4
1.7 Packing List .....................................................................5
1.8 Ordering Information .....................................................5
1.9 Specication....................................................................6
1.10 Board Dimensions........................................................7
Chapter 2 - Installation ......................................................9
2.1 Block Diagrams............................................................ 10
2.2 Jumpers and Connectors ...........................................11
Jumpers................................................................................. 12
JRS1: COM 2 RS-232/422/485 Select.....................12
LLED1: LAN LED Indicators...................................12
JFRT1: Switches and Indicators............................12
JBAT1: CMOS Setup ...............................................13
CON1: RS-422/ 485 Connector...............................13
Connectors ........................................................................... 14
KBM1: Keyboard & Mouse Connector ..................14
LAN1: Fast Ethernet Connector.............................14
IDE1: 44 pin IDE Connector....................................15
PWR1: Power Supply Connector...........................15
PC/104: PC/104 ISA Interface .................................16
IR1: Intrared Connector ..........................................17
VGA1: CRT Connector............................................17
USB1: USB Connector............................................17
FDD1: 20-pin FDD Connector.................................18

CON1: RS-422/ 485 Connector...............................18
LPT1: 20-pin Parallel Port Connector....................18
LCD1: TTL LCD Connector.....................................19
COM1/ COM2: Serial Port Connector ....................19
CFD1: CompactFlash II Socket ..............................20

1Chapter 1
Introduction
Chapter 1 - Introduction

1.1 Copyrights
This manual is copyrighted and all rights are reserved. It does not allow any non
authorization in copied, photocopied, translated or reproduced to any electronic or
machine readable form in whole or in part without prior written consent from the
manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special, incidental
or consequential damages arising from the use of inability to use the product or
documentation, even if advised of the possibility of such damages. The manufacturer
keeps the rights in the subject to change the contents of this manual without prior
notices in order to improve the function design, performance, quality and reliability. The
author assumes no responsibility for any errors or omissions, which may appear in this
manual, nor does it make a commitment to update the information contained herein.
Trademarks
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
All other trademarks, products and or product's name mentioned herein are mentioned
for identification purposes only, and may be trademarks and/or registered trademarks of
their respective companies or owners.
1

1.2 About User’s Manual
This User’s Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.
1.3 Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Single Board Computer, whenever components are separated
from the system.
2

1.4 Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer.
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
1.5 Technical Support
If you have any technical difculties, please consult the user’s manual rst.
Please do not hesitate to call or e-mail our customer service when you still
can not nd out the answer.
3

1.6 Warranty
This product is warranted to be in good working order for a period of two
years from the date of purchase. Should this product fail to be in good
working order at any time during this period, we will, at our option, replace
or repair it at no additional charge except as set forth in the following terms.
This warranty does not apply to products damaged by misuse, modications,
accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made
by any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
but not limited to implied warranties of merchantibility and tness for
a particular purpose, with respect to the hardware, the accompanying
product’s manual(s) and written materials, and any accompanying hardware.
This limited warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.
4

1.7 Packing List
If any of the above items is damaged or missing, contact your vendor
immediately.
1.8 Ordering Information
3007680
PC/104 CPU module with AMD Geode™
LX800 (500MHz), 1 x SO-DIMM, CRT/
LCD & LAN
1208420 (Optional)
Cable Kit
1 x USB Cable
2 x COM Port Cable
1 x FDD Flat Cable
1 x IDE Cable
1 x Parallel Port Cable
1 x LAN Cable
1 x VGA Cable
1 x KB/MS Cable
1 x 3007680 PC/104 CPU Module
1 x CD-ROM
1 x Quick Installation Guide
5

1.9 Specication
Form Factor PC/104 CPU module
Processor AMD Geode™ LX Series processor
Cache 64K L1 cache and 128K L2 cache
Chipset AMD LX800 + CS5536
System Memory 1 x 200-pin DDR SO-DIMM socket up to 1GB
SDRAM
VGA/ LCD Controller
AMD Geode LX series CPU integrated VGA
controller with 2D Engine (Shared memory Max.
64MB)
Ethernet Realtek 8100CL 10/100 base-T Ethernet
LCD Supports 18/24-bit TTL up to 1280 x 1024
I/O Chips W83627HG
BIOS Phoenix-Award PnP Flash BIOS
IDE Interface 1 x Ultra DMA 33, support 2 IDE devices
Serial Port 2 x RS-232 ports
COM2: RS-422/RS-422/RS-485 selectable
Parallel Port / Floppy 1 x SPP/EPP/ECP mode
1 x Floppy connector
KBMS Standard PS/2 Keyboard and Mouse
Universal Serial Bus 2 x USB 2.0 ports
PCI to ISA bridge ITE8888G
Expansion Bus 1 x PC/104 interface
Flash Disk 1 x Type II Compact Flash Disk Socket up to 4GB
Hardware Monitor Integrated in W83627HG
RTC AMD Geode CS5536 built-in RTC with lithium
battery
Power Input Connector 1*4-pin power connector
Operation Temp. -40 ~ 80ºC (-40 ~ 176ºF)
Watchdog Timer 1 - 255 Level (Sec. or Min.)
Dimension (L x W) 96 x 90 mm (3.8” x 3.5”)
6

1.10 Board Dimensions
Unit:mm
7

Unit:mm
8

2Chapter 2
Installation
Chapter 2 - Installation
9

2.1 Block Diagrams
1 x 200pin
SO-DIMM Socket
PCI LAN
Controller
LAN
RJ-45
Analog
R.G.B.
TTL
VGA
LCD
AMD Geode
LX800 CPU
500MHz
Memory Bus
USB I/F
IDE ATA I/F
1 x IDE
2 x USB
COM1
COM2
LPT1
FDD IrDA
KB
MS
1 x CF
CS5536
AMD Geode
Super IO
LPC I/F
PC/104
PCI to ISA
Bridge ISA Bus
PCI Bus
10

2.2 Jumpers and Connectors
10
91
2
JBAT1
13
COM1
17
KBM1
1
LAN1
2
IDE1
3
COM2
18
LCD1
16
LPT1
14
FDD1
12
USB1
11
VGA1
10
IR1
9
PWR1
4
JFRT1
8
LLED1
7
JRS1
6
PC/104
5
CON1
15
10
91
2
44 43
9
1
1
2
1
4
1
2
65
1
2
C19
B32
A32
D19
11
1
1
16
15 1
2
C0
A1
B1
D0
9
12
20
19
12
20
19
12
40
39
1
12
11

Jumpers
It can be congured COM2 to operate in RS-232, RS-422 or RS-485 mode
JRS1: COM 2 RS-232/422/485 Select (6)
LLED1: LAN LED indicators (7)
Pin Description
1 LAN1_LED0-
2 ACT_LED+
3LAN1_LED1-
4 LINK_LED+
1
JFRT1: Switches and Indicators (8)
It provides connectors for system indicators that provides light indication of
the computer activities and switches to change the computer status.
Pin Description
1 RESET+
2 GND
3 PWR LED+
4 GND
5 HDD LED+
6 HDD LED-
7 SPK OUT+
8 SPK OUT-
1
2
3
4
5
6
7
8
RESPLEDHLEDSPK
Mode 1-2 3-4 5-6
RS-232 (Default) ON OFF OFF
RS-422 OFF ON OFF
RS-485 OFF OFF ON
65
2
1
65
2
1
65
2
1
12

JBAT1: CMOS Setup (13)
Pin Mode
1-2 Keep CMOS (Default)
2-3 Clear CMOS
1
CON1: RS-422/ 485 Connector (15)
2.0 mm 4-pin wafer connector
Pin RS-422 RS-485
1 TX+ Data+
2 TX- Data-
3 RX+ N/C
4 RX- N/C
1
3
2
4
1
13

Connectors
KBM1: Keyboard & Mouse Connector (1)
6-pin Keyboard & Mouse wafer connector
Pin Description
1 KB_DATA
2 GND
3 MS_DATA
4 KB_CLK
5 KB_VCC
6 MS_CLK
1
LAN1: Fast Ethernet Connector (2)
Pin Description Pin Description
1 TX+ 2 TX-
3 RX+ 4 N/C
5 N/C 6 RX-
7 N/C 8 N/C
9 GND 10 N/C (Key)
10
9
12
14

IDE1: 44-pin IDE Connector (3)
Pin Description Pin Description
1 IDE RESET 2 GND
3 DATA7 4 DATA8
5 DATA6 6 DATA9
7DATA5 8 DATA10
9 DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C (Key)
21 REQ 22 GND
23 IO WRITE 24 GND
25 IO READ 26 GND
27 IO READY 28 N/C
29 DACK 30 GND
31 IRQ14 32 N/C
33 ADDR1 34 ATA66 DETECT
35 ADDR0 36 ADDR2
37 CS#2 38 CS#3
39 IDEACTP 40 GND
41 +5V 42 +5V
43 GND 44 N/C
4443
21
PWR1: Power Supply Connector (4)
Pin Description
1 +5V
2 GND
3 GND
4+12V
1
2
3
4
15

PC/104: PC/104 ISA Interface (5)
Connector type: PC104 press t 2x20-pin connector
A1
B1
A32
B32
D19
C19
D0
C0
Pin Description Pin Description Pin Description Pin Description
D0 GND C0 GND A1 IOCHCK# B1 GND
D1 MEMCS16# C1 SBHE# A2 SD7 B2 RST_DRV
D2 IOCS16# C2 LA23 A3 SD6 B3 +5V
D3 IRQ10 C3 LA22 A4 SD5 B4 IRQ9
D4 IRQ11 C4 LA21 A5 SD4 B5 N/C
D5 IRQ12 C5 LA20 A6 SD3 B6 DREQ2
D6 IRQ15 C6 SA19 A7 SD2 B7 N/C
D7 IRQ14 C7 SA18 A8 SD1 B8 0WS#
D8 DACK0# C8 SA17 A9 SD0 B9 +12V
D9 DREQ0 C9 MEMR# A10 IOCHRDY B10 GND
D10 DACK5# C10 MEMW# A11 AEN B11 SMEMW#
D11 DREQ5 C11 SD8 A12 SA19 B12 SMEMR#
D12 DACK6# C12 SD9 A13 SA18 B13 IOW#
D13 DREQ6 C13 SD10 A14 SA17 B14 IOR#
D14 DACK7# C14 SD11 A15 SA16 B15 DACK3#
D15 DREQ7 C15 SD12 A16 SA15 B16 DREQ3
D16 +5V C16 SD13 A17 SA14 B17 DACK1#
D17 MASTER# C17 SD14 A18 SA13 B18 DREQ1
D18 GND C18 SD15 A19 SA12 B19 REFRESH#
D19 GND C19 GND A20 SA11 B20 SYSCLK
A21 SA10 B21 IRQ7
A22 SA9 B22 IRQ6
A23 SA8 B23 IRQ5
A24 SA7 B24 IRQ4
A25 SA6 B25 IRQ3
A26 SA5 B26 DACK2#
A27 SA4 B27 TC
A28 SA3 B28 BALE
A29 SA2 B29 +5V
A30 SA1 B30 ISA_CLK
A31 SA0 B31 GND
A32 GND B32 GND
16
Table of contents
Other Global American Inc. Computer Hardware manuals

Global American Inc.
Global American Inc. 330827 User manual

Global American Inc.
Global American Inc. 3308290 User manual

Global American Inc.
Global American Inc. 3301825 User manual

Global American Inc.
Global American Inc. 3301730 User manual

Global American Inc.
Global American Inc. 3304280 User manual

Global American Inc.
Global American Inc. 3308130 User manual
Popular Computer Hardware manuals by other brands

ARM
ARM Cortex-M3 DesignStart Technical reference manual

ST
ST STM32Cube quick start guide

Fibocom
Fibocom FM150-NA Series user manual

MF DIGITAL
MF DIGITAL Scribe 9100 series Quick connect guide

Addonics Technologies
Addonics Technologies AD5U2SA installation guide

Atmel
Atmel ATSAMB11 BluSDK SMART user guide