GLOBAL ASSISTIVE DEVICES GLOBAL 360 User manual

Congratulations on your purchase of “GLOBAL
360”. This quality product is the answer for people
with special needs for wake up providing the unique
feature of an Auto Repeat Countdown Timer.
BEFORE using your unit, take a few minutes to
read the following instructions. The understanding
of the features will allow you ease in setting and
ensure effective use.
POWER SOURCE: Power Supply and Universal
Adapter Plugs Included
Insert the small barrel plug of the Power Supply
(Output: DC 12V, 1000 mA; Input 100-240 Volt 50-
60 Hz) into the jack at the back of the clock labeled
12V DC Adapter.
Connect the power supply with the adapter plug that
is required for your electrical outlet.
Plug into an Electrical outlet near your bedside.
Note: 12:00 will flash on the clock display. When
you set the time, the display will stop flashing.
BATTERY BACK UP: CR2032 Button Cell
Included
In the event of a power failure, the clock will keep
the clock time running and the preset times for

alarm and countdown timer. The clock display will
not light to save battery energy.
Note: If you have a long power failure you may
need to make a slight adjustment to the clock time
after the AC power returns.
To activate the battery backup function, open the
Circular Battery Door located on the bottom of the
clock by a turn counter clockwise and pull the
protective plastic tab out.
Note: Replace Battery as required.
The life expectancy of CR2032 battery is
approximately 2 years.
SETTING THE CLOCK TIME
Slide the SET MODE switch to “TIME”position.
Press and Hold the SET button and press the
HOUR button to set the hours.
Note: When using the 12 Hour Clock, note the
Yellow PM INDICATOR LIGHT located at the top
left of the clock display for accurate setting. When
the clock is reading PM time, the light will be "on".
The light will be off when the clock is reading AM
time.
Press and Hold the SET button and press the
MINUTE button to set the minutes.

SELECT 12 HOUR (AM/PM Time) OR 24 HOUR
TIME.
Slide the SET MODE switch to “TIME”position.
Press and Hold the SET button and press the
START/STOP button to change to your desired
format.
SELECT THE ALERT MODE: Vibrate, Audible or
Both
Slide the ALERT MODE switch (3-position switch
located on the left side of the clock) to select the
desired alerts for Clock Alarm and Countdown
Timer.
VIBRATE activates bedshaker.
AUDIBLE activates sound.
BOTH activates both bedshaker and sound.
When using the AUDIBLE Alert, the sound can be
adjusted.
Slide the AUDIBLE switch on the top of the clock to
“LOUD” or “SOFT”.
BEDSHAKER:
Insert the mini barrel plug of the Bedshaker cable
into the jack at the back of the clock labeled
BEDSHAKER.

Slide the ALERT MODE switch (3-position switch
located on the left side of the clock) to VIBRATE or
BOTH.
Place the Bedshaker under your pillow or mattress.
Slide the ALARM/COUNTDOWN TIMER switch (4
position switch located on the right side of the clock)
to BOTH ON position.
When the Alarm or Countdown Timer is activated,
the Bedshaker will pulse vibrate.
Press the START/STOP button to stop the vibration
alert.
ALARM CLOCK
Alert(s) set (VIBRATE, AUDIBLE or BOTH) will be
activated when the alarm time is reached.
Activated Alerts can be manually stopped by
pressing the START/STOP button (or will
automatically stop after approximately 20 minutes)
Set Alarm Time will remain set for daily alerts and
can be turned off when not wanted with
ALARM/COUNTDOWN TIMER switch.
SETTING THE ALARM TIME
Slide the SET MODE switch to “ALARM” position.
Press and Hold the SET button and press the
HOUR button to set the hours.

Note: When using the 12 Hour Clock, use the
Yellow PM INDICATOR LIGHT located at the top
left of the clock display for accurate setting. When
the display is reading PM time, the light will be "on".
The light will be off when the clock is reading AM
time.
Press and Hold the SET button and press the
MINUTE button to set the minutes.
The Blue ALARM Indicator light (located at the
bottom left of the clock display) will show.
The Alarm Time will remain set and will be activated
daily at the same time unless turned off or manually
changed.
TO CHECK THE ALARM TIME SETTING
Slide the SET MODE switch to “ALARM”. The
Clock Display will then show the alarm time that has
been set.
TURNING OFF CLOCK ALARM
Slide the ALARM/COUNTDOWN TIMER switch (4-
position switch located on the right side of the clock)
to CLOCK ALARM OFF or BOTH OFF when you
do not want the alarm clock to wake you.
The Alarm time will remain set for future use.

Note: The Blue ALARM indicator light will not show
on the display.
USING THE SNOOZE FEATURE
After the alarm is activated, press the SNOOZE
button to stop alert activity (audible, Bedshaker or
both).
Note: The Blue ALARM indicator light will flash.
In approximately 9 minutes the alert(s) will start
again automatically.
You can press the SNOOZE button to repeat this
cycle again and again.
COUNTDOWN TIMER
Program a Countdown Time for any amount of
minutes and/or hours up to 23 hours 59 minutes.
Alert(s) set (VIBRATE, AUDIBLE or BOTH) will be
activated when the countdown reaches “00.00”.
Activated Alerts can be manually stopped by
pressing the START/STOP button. (Clock display
can be in any MODE -TIME, ALARM or TIMER.)
Note: The auto stop feature will stop the alert(s)
automatically after approximately 30 minutes if
timer is set for 31+ minutes; after approximately 5
minutes if set for 6-30 minutes; and after
approximately 30 seconds if set for 1-5 minutes.

Programmed time will automatically repeat each
time the countdown reaches “00.00” unless turned
off manually.
SETTING THE COUNTDOWN TIMER:
Slide the SET MODE switch to “TIMER” position.
Press and Hold the SET button and press the
HOUR button to set the hours.
Press and Hold the SET button and press the
MINUTE button to set the minutes.
The Green COUNTDOWN TIMER Indicator light
(located at the bottom right of the clock display) will
show.
Press the START/STOP button to start the counting
down.
The Green Countdown Timer Indicator Light will
flash.
Note: The display will show the seconds counting
down when the time reaches the last minute.
To reset the Countdown Timer,
Press the START/STOP button to stop the
Countdown.
Press the SET button and the last set time will show
on the display.

Reset using the SET button and HOUR and
MINUTE buttons as noted above.
TO CHECK THE COUNTDOWN TIME SETTING:
Slide the SET MODE switch to “TIMER”. The Clock
Display will show the countdown time that has been
set or remains.
To check original time set, Press the START/STOP
button and then press the SET button.
Press the START/STOP button to continue
counting down the remaining time.
TURNING OFF COUNTDOWN TIMER:
Slide the ALARM/COUNTDOWN TIMER switch (4-
position switch located on the right side of the clock)
to COUNTDOWN TIMER OFF or BOTH OFF when
you do not want the countdown timer alerts.
The Countdown time will remain set.
Note: The Green COUNTDOWN TIMER indicator
light will not show on the display
STOPPING REPEAT OF COUNTDOWN TIME:
Slide the SET MODE switch to “TIMER”.
Press the START STOP button once.

Note: If the Alerts (Vibrate, Audible or Both) are
currently activated, Press the START/STOP button
twice.
CARE AND MAINTENANCE
GLOBAL 360 has been carefully designed and
manufactured to provide you with accuracy and
dependability. The following suggestions will help
you care for your clock/countdown timer so that you
can enjoy the maximum from it.
Keep the clock dry. If it gets wet, wipe it dry
immediately. Liquids can contain minerals that
corrode the electronic circuits.
Use only a fresh battery of the recommended size
and type. Always remove an old or weak battery. It
can leak chemicals that can damage electronic
circuits.
Handle the clock gently and carefully. Dropping it
can damage the circuit boards and case and can
cause it to work improperly.
Use and store the clock only in normal temperature
environments. Extreme temperatures can shorten
the life of electronic devices and distort or melt
plastic parts.

Keep the clock away from dust and dirt, which can
cause premature wear of parts.
Wipe the clock with a dampened cloth occasionally
to keep it looking new. Do not use harsh chemicals,
cleaning solvents, or strong detergents to clean the
clock.
Modifying or tampering with your clock's internal
components can cause a malfunction and will
invalidate the clock's warranty.
SERVICE:
Qualified service personnel should service the unit.
The user should not attempt to service the unit. All
servicing should be referred to:
ONE YEAR LIMITED WARRANTY
Your GLOBAL 360 is warranted to be free from
defects in material or workmanship for One Year
from the date of purchase. This is a limited warranty
and covers functions only. The warranty is void if
the unit has been tampered with, altered, abused,
or subjected to extreme conditions for which it was
not designed, or repaired other than by a qualified
service center. At its option, GLOBAL ASSISTIVE
DEVICES, INC. may select to replace the unit,
rather than repair it.

During the warranty period, return the unit, with
dated proof of purchase, in a secure package,
insured and with shipping charges prepaid. No
C.O.D. packages will be accepted. Please include a
note describing in detail the reason for return, your
return address and include $9.95 (check, money
order, Visa, MasterCard, American Express, or
Discover) for shipping and handling in the USA.
Other Countries please contact us for pricing.
OUT OF WARRANTY SERVICE
Follow the same procedure for shipping to us as
you would for warranty service. Be sure to include a
description of the problem. An estimate will be
submitted for your approval for any labor or parts
not covered by the warranty before any work is
performed.
DISCLAIMER:
In no event shall Global Assistive Devices, Inc. be
held liable for any special, incidental, indirect or
consequential damages whatsoever including, but
not limited to, damages for loss of property,
personal injury, loss of privacy, failure to meet any
duty, negligence, and any other loss whatsoever,
however caused, even if Global has been advised

of the possibility of such damages. This disclaimer
of liability applies to any damages or injury,
including but not limited to those caused by any
failure of performance of the product. Responsibility
for selection, safety and suitability of any product
rests with the consumer. Circumstances or
consequences arising out of or in any way related to
the use of or inability to use our products is the
responsibility of the consumer. Global Assistive
Devices, Inc. cannot be held liable in any way.
When an accessory that is not manufactured by
GLOBAL is used with this product, GLOBAL will not
accept any liability for the performance or
malfunction of the connected product.
GLOBAL ASSISTIVE DEVICES, INC.
Oakland Park, FL USA 33334
www.GlobalAssistive.com
“Global 360” is a trademark of GLOBAL ASSISTIVE DEVICES, INC.