GLOBAL ASSISTIVE DEVICES VibraLITE 2 User manual

VIBRATION WATCH with:
Vibration Alarm (won't disturb others).
Beep Alarm (optional)
Electro-Luminescent (EL) back light (for viewing display at
night).
Second Clock (great when traveling in a different time zone).
Two Alarm Settings (use for daily reminders, wake up & snooze,
medication)
Countdown Timer with manual reset can be set for minutes &
hours. (Use for reminders such as medication, medical conditions,
timing presentations or procedures, parking, cooking).
Hourly Alert/Chime Option
12 or 24 Hour clock
Stopwatch

OPERATING MODES
Your watch has six operating modes: To go from
one operating mode to another, repeat pressing
the MODE button for each mode to be displayed.
The operating modes will rotate in the order as
listed above.
TO BECOME FAMILIAR WITH THE
OPERATING MODES & THEIR SYMBOLS,
ROTATE THROUGH EACH MODE BY
PRESSING THE ‘MODE” BUTTON.

FIRST TIME SETTING OF YOUR CALENDAR/CLOCK
(You must have this set for your Alarm Settings to be accurate.)
When setting the Calendar & Clock, the rotation for setting is
Seconds, Hour, Minutes, 12/24Hr, Date, Month, Day of Week.
ONLY when the digits are BLINKING can you set or change the
setting. The clock will stop blinking when no button is pressed for
two minutes. You cannot switch to another mode of operation while
the display is blinking. To exit and stop the blinking, push
LAP/RESET button.
1. Repeat pressing the MODE button until the (1) CALENDAR
CLOCK operating mode shows on the display.
2. Press & Hold the LAP/RESET button until the seconds digits
begin to BLINK.
Press START/STOP button to reset the seconds display to 00.
3. Press the MODE button. The hour digits will begin to BLINK.
Press the START/STOP button to rotate to the correct hour of
the day.

WHEN IN THE 12 HR MODE, A PM INDICATOR WILL APPEAR
ON THE DISPLAY ABOVE AND LEFT OF THE HOUR DIGITS.
AS YOU ROTATE TO 12 HOURS THE PM MUST SHOW FOR
SETTING CORRECT TIME FOR AFTERNOON OR EVENING.
BE SURE TO SET CORRECTLY FOR THE CURRENT TIME
OF DAY.
4. Press the MODE button to go to the minute digits. The minute
digits will begin to BLINK.
Press the START/STOP button to rotate to the correct minute.
5. Press the MODE button and the 12H or 24H mode will show and
BLINK on the display. Press the START/STOP button to change
from 12H to 24H or from 24H to 12H preference.
6. Press the MODE button for the date of the month. A number will
BLINK at the top left corner of the display. Press START/STOP
button to rotate to the correct date of the month. (1 - 31)

7. Press the MODE button for the month. A number will BLINK on
the display. Press the START/STOP button to rotate to the
current month of the year. (Example; 6for June, 9for
September)
8. Press the MODE button for the Day of the Week. A two-letter
abbreviation at the top of the display will BLINK. Press the
START/STOP button to rotate to the correct day. (Example TU
for Tuesday; TH for Thursday)
9. Press the LAP/RESET button when you have finished the correct
set up. The display will stop blinking.
HOW TO SET AN ALARM CLOCK (Setting procedure is the same
for BOTH alarms)
1. Repeat Pressing the MODE button to rotate to the alarm
operating mode you want: A1 = 1st ALARM or A2 = 2ND
ALARM.

2. Press & Hold the LAP/RESET button until the hour digits BLINK.
Press the START/STOP button to rotate to the hour wanted.
Note: In the 12 Hr Mode, remember to use the PM indicator for
correct setting.
3. Press the MODE button to go to the minutes. The minutes will
BLINK. Press the START/STOP button to rotate to the minute
wanted.
4. Press LAP/RESET Button when finished. The display will stop
blinking. The set icon will show on the display. Your alarm is set.
When A1 Alarm is set the icon shows beside the PM indicator
under the Alm1.
When A2 Alarm is set the icon shows on the
display beside the A1 icon under the Alm2 icon.
Note: Calendar Clock Timer must be set for Alarm
Time activation to be correct.

HOW TO TURN ON AND OFF THE HOURLY ALERT
Note: Hourly Alert is a short single reminder
1. Repeat Pressing the MODE button and select either 1st ALARM
= A1 or 2ND ALARM = A2
2. Repeat Pressing START/STOP button until the
Hourly Alert indicator (located beside the Alm2
indicator) shows on the display. Hourly alert is on
when icon shows. Hourly alert is off when icon
doesn’t show.
ON/OFF SETTINGS OF ALARMS:
Note: To turn on or off First Alarm you must be in the A1 mode.
To turn on or off Second Alarm you must be in the A2 mode.
Repeat Pressing the MODE button to show alarm you wish to
turn off or on. 1ST OR 2ND ALARM.

Repeat Pressing the START/STOP button to rotate, alarm on
(hourly alert) & alarm off. When Icon(s) shows,
alarm is set. Alarm is off when icon does not show.
(See previous illustration)
HOW TO ACTIVATE OR DEACTIVATE VIBRATION AND BEEP
FUNCTION
1. Repeat Pressing MODE button to CALENDAR CLOCK mode.
2. Repeat Pressing the START/STOP button to rotate through the
selection of settings. When a function is activated, its respective
icon will be highlighted, at the top right corner of the display.
Rotation will be: Vibration ON, Beep ON, Vibration and Beep ON,
Vibration & Beep OFF. Select one of the four functions that you
desire. This can be changed at anytime by following steps 1 and 2.
Alarm will stop automatically after approximately 20 seconds. To
stop alarm before the automatic stop, press any button

NOTE: To verify setting the watch is in at any time, press the
MODE button. With each press of the button the vibration and/or
beep will respond if set.
HOW TO USE THE COUNTDOWN TIMER
1. Repeat Pressing the MODE button to display TR (COUNTDOWN
TIMER) operating mode.
2. Press and hold the LAP/RESET Button until the hour digits
BLINK. Press the START/STOP button to set the hour(s) wanted.
You can select from 0to 23 hours.
3. Press the MODE Button to go to the minutes. The minute digits
will BLINK. Press the START/STOP button to set the number of
minutes wanted. You can select from 0to 59 minutes.
4. Press LAP/RESET button when you have finished. The display
will stop blinking.

TO START THE COUNTDOWN TIMER, press the START/STOP
button (after the countdown timer is set).
The timer will start to countdown. To interrupt, press the
START/STOP button. Pressing the START/STOP button again will
start the countdown from where it last left off.
Note: When Countdown Timer is set for more than ten minutes, a
short single reminder will advise you of 10 minutes remaining and
then at 5 minutes remaining.
HOW TO USE THE STOPWATCH
1. Repeat Pressing the MODE button to show STOPWATCH on
the display.
2. To start the Stopwatch press the START/STOP button. The
Stopwatch will start keeping time and the Icon (symbol at the top
of the display) will flicker to show the action.

TO STOP THE STOPWATCH, press the START/STOP button.
Pressing the START/STOP button again will start the stopwatch
running from where it last left off. The Stopwatch can count up to 23
hours, 59 minutes and 59.99 seconds.
To RESET the stopwatch to zeros, press the LAP/RESET button,
when it is in a stop position.
Split Timing on Stopwatch
1. Start the Stopwatch by pressing the START/STOP button. The
stopwatch will start keeping time.
2. Press the LAP/RESET button. The watch will continue counting
the time even though you do not see it on the display. The Icon at
the top of the display will continue to flicker to show action and that
counting continues.
3. Press the LAP/RESET button again and the display will change
and show the time that has accumulated in total.

4. To RESET the Stopwatch, press the START/STOP button and
then press the LAP/RESET button.
HOW TO SET THE SECOND CLOCK
1. Repeat Pressing MODE button to show SECOND CLOCK (T2)
2. Press & Hold LAP/RESET button until the Hours digits BLINK.
Press the START/STOP button to rotate to the hour you wish to
set. (In 12 Hr Mode, use PM indicator for correct setting of
afternoon or evening.)
3. Press the LAP/RESET button when desired hour has been set.
NOTE: Only the hour can be set in second clock mode. (The
minutes and seconds will be the same as the Calendar Clock)
HOW TO USE THE EL BACK LIGHTPress the LIGHT button to
light up the LCD display at any time. The screen will be lit for
approximately 3 seconds before going off automatically.
(The EL back light will flash when an alarm is activated)

BATTERY INFORMATION
Your watch uses a Standard 3 volt lithium CR2032 or equivalent
battery. Battery life will vary due to how often the EL back light and
vibration function are used. To maintain water resistance, a
qualified person should replace the battery.
ONE YEAR LIMITED WARRANTY
Your VibraLITE 2is warranted to be free from defects in material or
workmanship for One Year from the date of purchase.
This is a limited warranty and covers watch functions only. This
warranty does not apply to the battery, the watchband, or to any
unit which has been subject to misuse, negligence or accident. This
warranty is void if the watch has been tampered with, altered, or
repaired other than by a qualified service center. At its option,
GLOBAL ASSISTIVE DEVICES, INC. may select to replace the
unit, rather than repair it. During the warranty period, return the
watch, with dated proof of purchase, in a secure package, insured
and with shipping charges prepaid. No C.O.D. packages will be
accepted. Please include a note describing the service required and

include $10.00 (check, money order, Visa, MasterCard, American
Express, or Discover) for shipping and handling in the USA. Other
Countries please contact us for pricing.
OUT OF WARRANTY SERVICE
Follow the same procedure for shipping to us as you would for
warranty service. Be sure to include a description of the problem.
An estimate will be submitted for your approval for any labor or
parts not covered by the warranty before any work is performed.
SERVICE:
Before sending your unit for service, have the battery checked
and/or try resetting by pushing all four buttons at the same time and
hold until the display clears. Qualified service personnel should
service this unit. The user should not attempt to service the unit.
Servicing should be referred to:
GLOBAL ASSISTIVE DEVICES, INC.
1121 East Commercial Boulevard, Oakland Park Florida US 33334

DISCLAIMER:
In no event shall Global Assistive Devices, Inc. be held liable for
any special, incidental, indirect or consequential damages
whatsoever including, but not limited to, damages for loss of
property, personal injury, loss of privacy, failure to meet any duty,
negligence, and any other loss whatsoever, however caused, even
if Global has been advised of the possibility of such damages. This
disclaimer of liability applies to any damages or injury, including but
not limited to those caused by any failure of performance of the
product. Responsibility for selection, safety and suitability of any
product rests with the consumer. Circumstances or consequences
arising out of or in any way related to the use of or inability to use
our products is the responsibility of the consumer. Global Assistive
Devices, Inc. cannot be held liable in any way.