GLOBAL ASSISTIVE DEVICES VibraLITE 3 User manual

VIBRATION WATCH with:
Vibration Alarm won't disturb others.
Beep Alarm option
Auto Reload Countdown Timer can be
set for seconds, minutes & hours. Use for
reminders such as medical conditions,
medication, timing presentations or procedures,
parking, cooking. Will automatically reload to
preset countdown time.
Electro-Luminescent backlight For viewing display at night
Second Clock great when traveling in a different time zone.
Two Alarm Settings use for daily reminders, wake up, snooze, medication
Hourly Alert/Chime Option
12 or 24 Hour clock
Stopwatch
OPERATING MODES
Your watch has six operating modes:
To go from one operating mode to another,
repeat pressing the MODE button for each
mode to be displayed. The operating modes
will rotate in the order as listed above.
TO BECOME FAMILIAR WITH THE
OPERATING MODES & THEIR SYMBOLS,
ROTATE THROUGH EACH MODE BY
PRESSING THE „MODE” BUTTON.
FIRST TIME SETTING OF YOUR
CALENDAR/CLOCK
(You must have this set for your Alarm Settings to be accurate.)
When setting the Calendar & Clock, the rotation for setting is Seconds, Hour, Minutes,
12/24Hr, Date, Month, Day of Week. ONLY when the digits are BLINKING can you set or
change the setting. The clock will stop blinking when no button is pressed for two

minutes. You cannot switch to another mode of operation while the display is blinking. To
exit and stop the blinking, push LAP/RESET button.
1. Repeat pressing the MODE button until the CALENDAR CLOCK operating mode
shows on the display.
2. Press & Hold the LAP/RESET button until the second‟s digits begin to BLINK.
Press the START/STOP button to reset the second‟s display to 00.
3. Press the MODE button. The hour digits will begin to BLINK.
Press the START/STOP button to rotate to correct hour of the day.
WHEN IN THE 12 HR MODE, A PM INDICATOR
WILL APPEAR ON THE DISPLAY ABOVE AND
LEFT OF THE HOUR DIGITS. AS YOU ROTATE
TO 12 HOURS THE PM MUST SHOW FOR
SETTING CORRECT TIME FOR AFTERNOON
OR EVENING. BE SURE TO SET CORRECTLY
FOR THE CURRENT TIME OF DAY.
4. Press the MODE button to go to the minute digits. The minute digits will begin to
BLINK.
Press the START/STOP button to rotate to the correct minute.
5. Press the MODE button and the 12H or 24H will show and BLINK on the display.
Press the START/STOP button to change from 12H to 24H or from 24H to 12H.
6. Press the MODE button for the date of the month. A number will BLINK at the top left
corner of the display. Press the START/STOP button to rotate to the correct date of the
month. (1 - 31)
7. Press the MODE button for the Month. A number will BLINK on the display. Press the
START/STOP button to rotate to the current month of the year. (Example; 6 for Jun, 9
for Sept)
8. Press the MODE button for the Day of the Week. A two-letter abbreviation at the top of
the display will BLINK. Press the START/STOP button to rotate to the correct day.
(Example TU for Tuesday; TH for Thursday)
9. Press the LAP/RESET button when you have finished the correct set up. The display
will stop blinking.
HOW TO SET AN ALARM CLOCK (Setting procedure is the same for BOTH alarms)
1. Repeat Pressing the MODE button to rotate to the alarm operating mode you want: A1
= 1st ALARM or A2 = 2ND ALARM.
2. Press & Hold the LAP/RESET button until the hour digits BLINK.
Press the START/STOP button to rotate to the hour wanted.
Note: In the 12 Hr Mode, remember to use the PM indicator for correct setting.
3. Press the MODE button to go to the minutes. The minutes will BLINK. Press the
START/STOP button to rotate to the minute wanted.

4. Press the LAP/RESET Button when
finished. The display will stop blinking.
The set icon will show on the display.
Your alarm is set.
When A1 Alarm is set the icon shows
beside the PM indicator under Alm1.
When A2 Alarm is set the icon shows on the display beside the A1 icon under Alm2.
Note: Calendar Clock Time must be set for Alarm Time activation to be correct.
HOW TO TURN ON AND OFF THE HOURLY ALERT
Note: Hourly Alert is a short single reminder
1. Repeat Pressing the MODE button and
select either 1st ALARM=A1 or 2ND
ALARM=A2
2. Repeat Pressing START/STOP button
until the Hourly Alert indicator (located
beside the Alm2 indicator) shows on the
display. Hourly alert is on when icon shows.
Hourly alert is off when icon doesn‟t show.
ON/OFF SETTINGS OF ALARMS
Note: To turn on or off First Alarm you must be in the A1 mode.
To turn on or off Second Alarm you must be in the A2 mode.
Repeat Pressing the MODE button to show alarm you wish to turn off or on: 1ST OR
2ND ALARM.
Repeat Pressing the START /STOP button to rotate, alarm on (hourly alert) & alarm off.
When Icon(s) shows, alarm is set. Alarm is off when icon does not show. (See previous
illustration)
HOW TO ACTIVATE OR DEACTIVATE VIBRATION AND BEEP FUNCTION
1. Repeat Pressing the MODE button to the
CALENDAR CLOCK mode.
2. Repeat Pressing the START/STOP button to
rotate through the selection of settings. When
a function is activated, its respective icon will
be highlighted, at the top right corner of the
display. Rotation will be: Vibration ON, Beep
ON, Vibration and Beep ON, Vibration & Beep
OFF. Select one of the four functions that you desire.
This can be changed at anytime by following steps 1 and 2.
Alarm will stop automatically after approximately 20 seconds. To stop alarm before the
automatic stop, press any button. NOTE: To check setting the watch is in at any time,
press the MODE button. With each press of the button the vibration and/or beep will
respond if set.

HOW TO USE THE COUNTDOWN TIMER
1. Repeat Pressing the MODE button to display TR (COUNTDOWN TIMER) operating
mode.
2. Press & Hold the LAP/RESET Button until the Seconds digits BLINK. Press the
START/STOP button to set to the seconds wanted. You can select from 0 to 59
seconds. If you do not wish to set the seconds, go to #3 below.
3. Press the MODE Button to go to the hours. The hour digits will BLINK. Press the
START/STOP button to set the number of hours wanted. You can select from 0to 23
hours.
4. Press the MODE Button to go to the minutes. The minute digits will BLINK. Press the
START/STOP button to set the number of minutes wanted. You can select from 0to 59
minutes.
5. Press LAP/RESET button when you have finished. The display will stop blinking.
To reset the Countdown Timer for a different time see "How to Use the Countdown
Timer" and follow instructions.
TO START THE COUNTDOWN TIMER,
Press the START/STOP button (after the countdown timer is set).
The timer will start to countdown.
To interrupt, press the START/STOP button. Pressing the START/STOP button again will
start the countdown from where it last left off.
Note: When Countdown Timer is set for more than ten minutes, a short single reminder
will advise you of 10 minutes remaining and then at 5 minutes remaining.
AUTO RELOAD COUNTDOWN TIMER will automatically reload for the time preset,
when the timer reaches “0”
If you do not wish to start the countdown again immediately, press the START/ STOP
button twice, if alarm is activated. Press once to stop the countdown if alarm is not
activated.
To restart the preset countdown at any time, press the START/STOP button while in the
COUNTDOWN - TR mode.
TO USE THE REPEATABLE COUNTDOWN TIMER WITH PAUSES IN BETWEEN
When the auto-repeat countdown timer reaches zero it automatically alarms and starts to
countdown again for the preset time. You can cancel the countdown before it reaches
zero and return to the original countdown time as needed.
You must be in the Countdown Timer Mode to reset to the original countdown time.
PUSH the LAP/RESET button and HOLD IT for approximately 2 to 3 seconds. Digits will
flash showing the amount of time that the countdown was set for originally.

Push the LAP/RESET button once, and the digits will stop flashing. (If you do not push
the LAP/RESET button to stop the flashing, the digits will stop flashing automatically after
2 minutes.)
To activate the start of the countdown when you need it, push the START/STOP button
once.
HOW TO USE THE STOPWATCH
1. Repeat Pressing the MODE button to show STOPWATCH on the display.
2. To start the Stopwatch press the START/STOP button. The Stopwatch will start
keeping time and the Icon (symbol at the top of the display) will flicker to show the
action.
TO STOP THE STOPWATCH, press the START/STOP button. Pressing the
START/STOP button again will start the stopwatch running from where it last left off. The
Stopwatch can count up to 23 hours, 59 minutes and 59.99 seconds. Each hour
accumulated shows at the top left of the display.
To RESET the stopwatch to zeros, press the LAP/RESET button, when it is in a stop
position.
Split Timing on Stopwatch
1. Start the Stopwatch by pressing the START/STOP button. The stopwatch will start
keeping time.
2. Press the LAP/RESET button. The watch will continue counting the time even though
you do not see it on the display. The Icon at the top of the display will continue to flicker
to show action and that counting continues.
3. Press the LAP/RESET button again and the display will change and show the time that
has accumulated in total.
To RESET the Stopwatch, press the START/STOP button and then press the
LAP/RESET button.
HOW TO SET THE SECOND CLOCK
1. Repeat Pressing the MODE button to show SECOND CLOCK (T2)
2. Press & Hold the LAP/RESET button until the Hours digits BLINK.
Press the START/STOP button to rotate to the hour you wish to set. (In 12 Hr Mode,
use PM indicator for correct setting of afternoon or evening.)
3. Press the LAP/RESET button when desired hour has been set.
NOTE: Only the hour can be set in second clock mode. (The minutes and seconds will
be the same as the Calendar Clock)
HOW TO USE THE EL BACK LIGHT
Press the LIGHT button to light up the LCD display at any time. The screen will be lit for
approximately 3 seconds before going off automatically.
The EL back light will flash when an alarm is activated

BATTERY INFORMATION
Your watch uses a Standard 3 volt lithium CR2032 or equivalent battery. Battery life will
vary due to how often the EL back light and vibration function are used. To maintain
water resistance, a qualified person should replace the battery
ONE YEAR LIMITED WARRANTY
Your VibraLITE 3 is warranted to be free from defects in material or workmanship for One
Year from the date of purchase. This is a limited warranty and covers watch functions
only. This warranty does not apply to the battery, band or to any unit which has been
subject to misuse, negligence or accident. This warranty is void if the watch has been
tampered with, altered, or repaired other than by a qualified service center. VibraLITE
watches are not intended to be worn during swimming, diving, or showering. At its option,
GLOBAL ASSISTIVE DEVICES, INC. may select to replace the unit, rather than repair it.
During the warranty period, return the watch, with dated proof of purchase, in a secure
package, insured and with shipping charges prepaid. No C.O.D. packages will be
accepted. Please include a note describing the service required and include $10.00
(check, money order, Visa, MasterCard, American Express, or Discover) for shipping and
handling in the USA. Other Countries please contact us for pricing.
OUT OF WARRANTY SERVICE
Follow the same procedure for shipping to us as you would for warranty service. Be sure
to include a description of the problem. An estimate will be submitted for your approval
for any labor or parts not covered by the warranty before any work is performed.
SERVICE:
Before sending your unit for service, have the battery checked and/or try resetting by
pushing all four buttons at the same time and hold until the display clears. Qualified
service personnel should service this unit. The user should not attempt to service the
unit.
Servicing should be referred to:
GLOBAL ASSISTIVE DEVICES, INC.
1121 East Commercial Boulevard
Oakland Park FL US 33334
DISCLAIMER:
In no event shall Global Assistive Devices, Inc. be held liable for any special, incidental,
indirect or consequential damages whatsoever including, but not limited to, damages for
loss of property, personal injury, loss of privacy, failure to meet any duty, negligence, and
any other loss whatsoever, however caused, even if Global has been advised of the
possibility of such damages. This disclaimer of liability applies to any damages or injury,
including but not limited to those caused by any failure of performance of the product.
Responsibility for selection, safety and suitability of any product rests with the consumer.
Circumstances or consequences arising out of or in any way related to the use of or
inability to use our products is the responsibility of the consumer. Global Assistive
Devices, Inc. cannot be held liable in any way

QUICK REFERENCE Model VL300
SELECTION OF VIBRATION, BEEP, BOTH OR OFF SIGNAL (S)
Press MODE button until the CALENDAR CLOCK mode shows on the display. Repeat pressing START/STOP
button to select desired function. Icon(s) at top right of display will indicate function: Vibration, Beep, Both or Off.
A Quick Check to see what function is set, is to push the MODE button while in the Calendar Clock mode. The
function that is set will respond each time you push the MODE button.
SETTING OF ALARMS AND COUNTDOWN TIMER
Press MODE button to rotate to the mode you wish to set. (TR for COUNTDOWN TIMER; A1 or A2 for ALARMS)
Press and Hold LAP/RESET button until the digits blink. While digits blink, press the START/ STOP button to
advance the blinking function to the time wanted. Press the MODE button to change from hours to minutes and
advance the time by pushing START/STOP button. For alarm settings, hour(s) and /or minute(s) can be set. For
countdown timer, seconds and/or hour(s) and minute(s) can be set. Press the LAP/RESET button when completed.
(Digits will stop blinking) In the Alarm(s) mode, the alarm indicator icon shows which alarm is activated.
To reset Alarms & Countdown Timer for a different time, repeat instructions as above.
Note: The calendar clock time must be set correctly for the alarm(s) to respond accurately.
Alarm settings are activated by the time on the calendar clock.
AUTO RELOAD COUNTDOWN TIMER
When the countdown timer reaches "0", it will automatically reload for the time that was preset. If you do not wish to
start the countdown again immediately, press the START/ STOP button twice, if the alarm is activated. Press once
to stop the countdown if the alarm is not currently activated. To restart the preset countdown at any time, press the
START/STOP button while in the TR (COUNTDOWN) mode.
HOURLY ALERT SETTING
Press the MODE button until display is in an ALARM Mode. (A1 or A2) Repeat pressing the START/STOP button until
the Hourly Chime icon shows. (Located beside the A2 icon)
Copyright: GLOBAL ASSISTIVE DEVICES, INC., Oakland Park Florida USA