GlobaLux Lighting LCS Series User manual

LCS Series
Installation Instructions
GlobaLux Lighng LLC – 2037 S. Vineyard Ave. Ontario, CA 91761 – 909-591-7605 Fax: [phone]
www.globaluxlighng.com
RIS9398
1/2
Safety Precauons
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND SAVE THEM.AS YOU MAY NEED THEM AT A LATER DATE.
1. WARNING: Failure to install and wire fixture in accordance with the Naonal Electrical Codes(NEC),all
applicable Federal, State and Local electrical codes, as well as specific ETLsafety standards for the intended
working environment(locaon/applicaon),may cause serious personal injury, death and/or property
damage. This product must be installed by a person familiar with the construcon and operaon of the
product and the hazards involved.
2. CAUTION:TURN OFF POWER FROM THE MAIN CIRCUIT BEFORE INSTALLING FIXTURE. Make sure fixture is
grounded per Naonal Electrical Codes (NEC).
3. IMPORTANT NOTE: The safeguards and instrucons appearing on this page, are not meant to cover all
possible condions and situaons that may occur. It may be understood that common sense, cauons, and
care are factors which cannot be built into any product. The person(s) installing, operang and responsible
for the light fixture，must execute these factors.
4. WARNING: Risk of fire and electrical shock. Most dwellings built before 1985 have supply wires rated 60°Ｃ.
Consult a qualified electrician before installing. If supply wires are located within 3 inches of the ballast, use
wires rated at least 90°Ｃ
TURN OFF POWDER FROM THE MAIN CIRCUIT BEFORE INSTALLING FIXTURE.
1. To help prevent the possibility of electrical shock, the use for rubber sole shoes is recommended.
2. Exercise care, use work gloves when handling the fixture to avoid cuts or abrasions.
3. Press channel and remove channel cover. Inside you will find the lampholder(s).
4. Install fixture: Locate ceiling joints and screw in fixtures using wood screws of ap-propriate length (screws
not included). Use toggle bolts for drywall mounng.
5. Electrical Connecons: Connect green/or bare copper wire to the green ground wire of fixture. (Ground
wire must be properly aached or unit may not work). If quick connector not provided: Connect the white
supply wire to the white fixture wire, cover them with a wire nut/or twist together and cover really well
with Electrical tape. Connect the black supplier wire to the black fixture wire, cover them with a wire If
quick connector provided: Plug the Line wire to black hole in quick connector. Plug the Neutral wire to
white hole in quick connector. Tips: Try to pull the wire out to test if it’s ghten enough.
Assembly Instrucons
NEEDED TOOLS
Safety Glasses
Ruler/Tape Measure
Flat Blade Screwdriver
Phillips Screwdriver
Adjustable Wrench
Drill
3/16” Drill Bit
3/32” Drill Bit
Pliers

Hoist installaon diagram:
sling chain
Lamp holder
Lens
Channel Cover
LED Module
Housing Channel
Self-tapping screw
Neutral
Ground
Green
Hot
WAGO
White
P2
Black
Black (5) Luminaire Disconnect
Black
120V~277V
SERVICE
Black
White
Ground Wire
Ground Wire
WIRE CONNECTOR
White White
Driver
WIRE CONNECTOR
WIRE CONNECTOR
Purple
Gray
Dimming +
Dimming -
1-10V
LED Module
+
-
+
-
L
N
1-10V
Gray
V-
Purple
V+
Dimming
Black (5) Luminaire Disconnect
Black
120V~277V
SERVICE
Black
White
Ground Wire
Ground Wire
WIRE CONNECTOR
White White
Driver
LED Module
+
-
+
-
L
N
Non dimming wiring diagram:
Dimming wiring diagram:
Installaon Instrucons
GlobaLux Lighng LLC – 2037 S. Vineyard Ave. Ontario, CA 91761 – 909-591-7605 Fax: [phone]
www.globaluxlighng.com
RIS9398
2/2
LED Strip Light
6. Place Channel Cover back on Housing Channel. Then place the lens on the channel cover.
7. Turn power on.
Installaon diagram: